FELIXprinters Pro Series Guía de instalación y uso

How To print a vase / spiral contour

11 June 2016

Revision 2

Repetier-Host for FELIXprinters

How To print a vase / spiral contour

11 June 2016

1

FELIX Pro 1

www.FELIXprinters.com

Introduction

1Introduction

In some cases it is desired to make a watertight object. A vase for instance is a good example. There is a

feature called spiralizer contour. This function only prints the outside contour of an object, and does this in a

single spiral. So there are no distinct layers.

This tutorial shows you how to print a spiral contour in repetier-host with cura slicer.

1. Start Repetier-Host.

2. Goto slicing settings, select CuraEngine and press configuration.

How To print a vase / spiral contour

11 June 2016

2

FELIX Pro 1

www.FELIXprinters.com

Introduction

3. In the slicing settings.Select the option …

4. Press save as …, it is recommended to make a custom profile for future use. After that close the

window.

1

2

3

4

Sometimes it is necessary to cut off the bottom

of the object. Fill in the amount of mm which

need to be removed.

How To print a vase / spiral contour

11 June 2016

3

FELIX Pro 1

www.FELIXprinters.com

Introduction

5. Now load the object and make sure you selected the correct print-configuration which you just

saved. press slice. Note that it is not possible to have the spiral contour with two objects.

Sliced object:

Note the large amount of layers. This is a bug in the software. It takes almost each line segment as a

separate layer because it is not able to distinguish the layers in spiral mode.

6. Reduce the flowrate to 50% and press print

1

2

How To print a vase / spiral contour

11 June 2016

4

FELIX Pro 1

www.FELIXprinters.com

Introduction

If you are unable to continue or have any questions, you can check at the support section of our website or

you can contact us directly:

Website: www.felixprinters.com/support

Email: support@felixprinters.com

Telephone: +31 (0)30 30 31 387

Address: Zeemanlaan 15, 3401MV IJsselstein, The Netherlands

Kind regards,

FELIXprinters

1

2

Otros manuales para Pro Series

10

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Impresora 3D de FELIXprinters

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Felix 2.0 Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro L Manual de usuario

FELIXprinters

FELIXprinters Pro Series Guía de instalación y uso

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters Tec 4 Manual de usuario

FELIXprinters

FELIXprinters FELIX Pro 2 Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de funcionamiento

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters Pro Series Manual de usuario

FELIXprinters

FELIXprinters FELIX Pro 3 Touch Manual de usuario

FELIXprinters

FELIXprinters Felix Pro 1 Manual de usuario

FELIXprinters

FELIXprinters Pro 2 Touch Manual de usuario

FELIXprinters

FELIXprinters FELIX Tec 4.1 Manual de usuario

FELIXprinters

FELIXprinters Pro Series Guía de instalación y uso

FELIXprinters

FELIXprinters FELIX One Manual de usuario

FELIXprinters

FELIXprinters FELIX Pro 2 Manual de usuario

FELIXprinters

FELIXprinters Tec 4 Manual de usuario

FELIXprinters

FELIXprinters Pro Series Manual de uso y cuidado

FELIXprinters

FELIXprinters 3 Series Manual de usuario

FELIXprinters

FELIXprinters Felix Pro 1 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario