F&F FW-R2P Manual de usuario

F&F Filipowski sp. j.

ul. Konstantynowska 79/81, 95-200 Pabianice

tel./fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: fif@fif.com.pl

Do not dispose of this device to thrash with other unsorted waste! In accordan-

ce with the Waste Electrical and Electronic Equipment Act any household electro-wa-

ste can be turned in free of charge and in any quan ty to a collec on point established

for this purpose, as well as to the store in the event of purchasing new equipment (as

per the old for new rule, regardless of brand). Electro-waste thrown in the trash or aban-

doned in the bosom of nature pose a threat to the environment and human health.

Wireless system

- 1 -

Description of the system

F&Wave is a family of wireless devices controlled by radio with a range of up to 100

meters*. The receivers are available in either a DIN-rail mounting version (housing 1S)

or a Ø60 flush-mounted version. The transmitters are available as handheld remo-

te controllers or as a flush-mounted version. The receivers relay control signals. The

device that receives a control signal from the transmitter will automatically send it

forward, which allows to increase the range of the remote control.

* Range of up to 100 meters in open space without any interfering factors. In building conditions and in the presence of

interference sources (power lines, transmitters, etc.) the actual range may be smaller.

FW-R2P

Dual bistable relay

- 2 -

Features of the module

Dual bistable relay;

Cooperation with remote control transmitters of the F&Wave system;

The ability to control from up to 8 transmitters;

Two local control inputs - the ability to directly control the relay using any mono-

stable buttons (for example: bell buttons);

Two independent NO output contacts with load capacity of 4 A (AC-1) each (inter-

nally connected to L);

Small enclosure size;

Screw terminals for easy installation in a Ø60 flush-mounted box;

Retransmission of commands from the transmitter - the ability to increase the

range of the remote control;

Low power consumption - low operating cost;

Built-in electronic thermal protection to prevent damage in case of excessive load

of the controller.

Installation of this device should be carried out by a qualified installer

after reading this manual. Dismantling the casing of the device will au-

tomatically void the warranty. Before starting the assembly, make sure

that the connecting wires are not live. Conditions of storage, transport

and use affect the proper operation of the device.

Description of the device

- 3 -

Control inputs do not cooperate

with backlighted buttons.

L - power supply L

N - power supply N

S1 - control input triggered with level L or N -

- channel 1

S2 - control input triggered with level L or N -

- channel 2

R1 - NO contact - channel 1

R2 - NO contact - channel 2

After proper connection, press and hold the PROG but-

ton until the circuit of the first channel will switch on and

the communication LED will go off.

To select a second channel for pairing, hold the program-

ming button again until the circuit of the second channel

switches on.

The actual maximum load depends on the na-

ture and design of the receiver.

For more information visit: www.fif.com.pl

2× 4 A/250 V (AC-1)

①

Each channel of the receiver is independently paired.

Connection

Load capacity

Pairing

- 4 -

③Correct pairing will be confirmed by temporary switching off of the output

circuit and the LED will turn on again.

To clear the list of transmitters cooperating with the receiver, press the PROG button and hold it

down for at least 10 seconds. Fast flashing of communication LED will indicate that the memory

of the controller has been cleared.

Each channel of the receiver can be paired with eight different transmit-

ters (remote buttons). Pairing with more buttons will remove the first en-

tries made.

Short press of a button switches the relay in to the opposite state.

Long press of a button (longer than 5 second) activates the relay regardless of the state, in which

the relay was previously in. This feature can be used for synchronizing a group of receivers con-

nected to the same local button. Releasing the button sets the relay in the off position.

The FW-RC4, FW-RC10 transmitters operate on the principle of a bistable switch: one

press of a button activates the relay; the second press of button deactivates the relay.

The FW-RC5 transmitter also has separate inputs ON (always ON) and OFF (always

OFF).

Press the selected button on a remote control or in

a flush-mounted transmitter.

②

Unpairing

Local buttons

Remote buttons

Due to the nature of transmission and retransmission do not use the same but-

ton in transmitter more often than every 2 seconds. Switching of the receiver

may be carried out with a short delay.

- 5 -

Transmitters Receivers Box Ø60 DIN rail

flush-mounted Single relay FW-R1P FW-R1D

FW-RC5 Double relay FW-R2P FW-R2D

remote controls Universal dimmer FW-D1P FW-D1D

FW-RC4 Roller blind controller FW-STR1P FW-STR1D

FW-RC10 Two-channel LED controller FW-LED2P FW-LED2D

Devices of the F&Wave system

We do not recommend the use of remote bistable transmitters to control

a group of receivers due to the possibility of desynchronization of the activation

state (especially when operating on larger distances and/or simultaneous use

of local buttons on the receivers).

Activation of the thermal protection is indicated by a steady pulsing of commu-

nication LED, switching off of the output circuit and the lack of its reactivation

possibility. After lowering the temperature to a safe value the output circuit will

remain switched off until restarted.

- 6 -

power supply 85÷265 V AC/DC

control input 85÷265 V AC/DC; <1 mA

power consumption

operating mode 1.00 W

standby 0.25 W

output load capacity (AC-1) 2× 4 A/250 V

radio frequency 868 MHz

working temperature -25÷65°C

terminal 2.5 mm² screw terminals

tightening torque (max) 0.4 Nm

mounting Ø60 flush-mounted box

dimensions 48×43×20 mm

ingress protection IP20

FW160415

Technical data

Compliance with the standards

PN-EN 60669, PN-EN 60950, PN-EN 55024, PN-EN 61000,

PN-ETSI EN 300 220-1, PN-ETSI EN 300 220-2,

PN-ETSI EN 301 489-1, PN-ETSI EN 301 489-3.

CE declaration of conformity is available for download at: www.fif.com.pl.

Warranty

F&F products are covered by a 24 month warranty from the date of purchase.

The warranty is effective only with a proof of purchase.

Contact your dealer or directly with us.

For more information on the procedure for submitting a warranty claim visit our web-

page: www.fif.com.pl/reklamacje

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Relé de F&F

Manuales populares de Relé de otras marcas

Shelly

Shelly Pro Series Manual de usuario

GE MVAX 11 Manual de usuario

ABB

ABB RELION REF615R Manual de usuario

Pilz

Pilz PNOZ X10 Manual del propietario

ABB

ABB SPAJ 142 C Manual de lista de piezas

Kemo Electronic

Kemo Electronic B197 Manual de usuario

Seg

Seg MRM3 Manual de usuario

Basler

Basler BE1-700C Manual de usuario

CD Automation

CD Automation REVEX 2PH 280A Manual de usuario

Ruelco

Ruelco 1S04 Manual de usuario

Basler

Basler V3E Z1P B2C1F Manual de usuario

Doepke

Doepke Dupline DSM 2 Manual de usuario

Siemens

Siemens SIRIUS 3RT1966-4D Manual de usuario

GE DGP Manual de usuario

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Manual de usuario

Siemens

Siemens SIPROTEC 4 Manual de usuario

Siemens

Siemens BD2-AK03X/FS Series Manual de usuario

Leuze

Leuze MSI-SR5B Manual de usuario