F&F PZ-829 RC Manual de usuario
- 1 -
PZ-829 RC
Fluid level control relay,
2-position
Fluid level control relays PZ-829 is devised to detect the pre-
sence of conductive liquids reaching the level of the sensor. It al-
low control MAX and MIN statues set by user of controlled fluid.
After the liquid level decreases to MIN (i.e. electrodes MIN and
COM spaced), the MIN contact is switched to position 11-12,
whereas the MAX contact remains in position 8-9. On the other
hand, when the MAX liquid level is reached (MAX and COM elec-
trodes shorted), the relay’s MIN contact will be switched to po-
sition 11-10, whereas the MAX into position 8-7.
Electrode probe connected with a cable with a wire dia-
meter of up to 1 mm² and a maximum length of 100 m.
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collecon, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.
1.Take OFF the power.
2.Put on the relay on the rail in the switchgearbox.
3.Connect power to contacts 1-2 with marks.
4.Probe connect to relay by cable <1 mm².
5.Install the probes at heights corresponding to the fluid control
levels.
6.Connect the MAX relay contact in series into the power supply
circuit of the draining device (terminals 8-7).
7.Connect the MIN relay contact in series into the power supply
circuit of the filling device (terminals 11-12).
8.Set the sensitivity with the knob.
Terminals 4-5-6 separated from the network.
Diagram
Mounting
- 3 -
Tank filling
Wiring diagram
- 4 -
Tank emptying
- 5 -
power supply 230 V AC
maximum load current (AC-1) 2×16 A
contact separated 2×NO/NC
sensitivity (adjustable) 1÷100 kΩ
contact switching delay
for MIN level 1÷2 s
for MAX level <5 s
voltage of measuring outputs 6 V
power signalling green LED
work status signalling 2× red LED
power consumption 1.1 W
working temperature -25÷50°C
terminal 2.5 mm² screw terminals (cord)
4.0 mm² screw terminals (wire)
tightening torque 0.5 Nm
dimensions 3 modules (52.5 mm)
mounting on TH-35 rail
ingress protection IP20
type of flood probe 3×PZ2
probe current 0.13 mA
sensor voltage 6 V
separation of measuring probes galvanic (transformator)
Technical data
- 6 -
F&F products are covered by a 24-month warranty from the date
of purchase. The warranty is only valid with proof of purchase.
Contact your dealer or contact us directly.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found www.fif.com.pl on the product subpage.
Warranty
CE declaration
E200527
Tabla de contenidos
Otros manuales de Relé de F&F
F&F
F&F PCS-533 Manual de usuario
F&F
F&F PK-1P Manual de usuario
F&F
F&F PK-4PZ Manual de usuario
F&F
F&F PP-1P Manual de usuario
F&F
F&F PP-1Z-LED Pico Manual de usuario
F&F
F&F BIS-411i Manual de usuario
F&F
F&F BIS-413 Manual de usuario
F&F
F&F BIS-410 Manual de usuario
F&F
F&F PCS-516UNI Manual de usuario
F&F
F&F FW-R1P Manual de usuario
F&F
F&F PK-3P Manual de usuario
F&F
F&F PCS-517.2 Manual de usuario
F&F
F&F SWITCH & ENERGY Wi-R1S1-P Manual de usuario
F&F
F&F BIS-412M 24V Manual de usuario
F&F
F&F CP-721-FPV Manual de usuario
F&F
F&F BIS-411-LED Manual de usuario
F&F
F&F BIS-416 Manual de usuario
F&F
F&F BIS-410-24V Manual de usuario
F&F
F&F BIS-411BM-LED Manual de usuario
F&F
F&F 5908312592389 Manual de usuario
