Extreme Networks Alpine 3804 Manual
Modem String Configuration for Remote Access
This document is intended to provide the necessary steps for adding a modem for remote access.
Required Equipment:
• Modem
• Modem power supply
• RJ-11 phone patch cable
• 9-pin male-to-25-pin female serial cable
• Analog phone line
• AC power source
Generic Hardware Configuration
Warning
– When attempting to connect a modem to a BlackDiamond MSM console port, make sure to plug the
external modem into the console port not the modem port. The MSM modem port does not function with
external modems attached.
Connection to the console port is used for direct local management. The console port
Settings are configured as follows:
• Baud Rate: 9600
• Data Bits: 8
• Stop Bit: 1
• Parity: None
• Flow Control: XON/XOFF
For best results, an AT initialization string should be customized for the modem. This can be obtained from the
modem documentation or the modem manufacturer.
The modem must be attached to the Extreme box to do the following:
• Raise DCD (Data Carrier Detect) when a call comes in (typically &C1)
• Ignore DTR/DTR Override (typically &D0)
• Use XON/XOFF software flow control (typically &K2 or &K4. &F2 on some USRs)
• Answer on the first ring (typically S0=1)
>>>
Laptop Computer
US Robotics 33.6 External Faxmodem model 839
or Hayes Accura 336 Fax Modem
AC Power Supply RJ-11 Telephone
Patch Cable 9-pin Male-to-
25-pin Female
Serial Cable
Remote Dial-up Connection
Depending on what type of modem you have, it may be necessary to lock down the DTE speed to 9600. Some
modems require a special AT command or dipswitch setting to lock the DTE speed. Check the manual for
your modem.
US Robotics 33.6 external fax/modem model 839
Modem-specific configuration parameters:
• Connect modem to PC/laptop, launch terminal session.
• Enter the following command string (fixes serial port speed and writes new config to default memory
location): AT&B1&W
• Turn off and disconnect the modem.
• Change the dip switches to the following:
1 – Down* DTR override
2 – Up Verbal result codes
3 – Up Suppress result codes
4 – Down No echo, offline commands
5 – Up Auto answer on first ring
6 – Up Carrier detect normal
7 – Down Load NVRAM defaults
8 – Up Dumb mode
*Down correlates to the underside of the modem chassis. Up correlates to the top of the chassis.
• Reconnect equipment according to the diagram above.
Hayes Accura 336 fax/modem
Modem-specific configuration parameters:
• Connect modem to PC/laptop, launch terminal session.
• Enter the first command string: AT&F&C1&D0S37=9S0=1&W
Parameter Explanation
&F – Clear previous configuration by setting modem to factory default
&C1 – Normal CD Operations
&D0 – DTR Over-ride
S37=9
S0=1 – Set auto answer to first ring
&W – Write configuration to memory
• Enter the second command string: ATQ1&W
Parameter Explanation
Q1 – Suppress Result Codes
&W – Write additional parameter to memory
• Turn off and disconnect the modem.
– Reconnect equipment according to the diagram above.
Verified Modem Init Strings
Dynalink Model 1456ER2
The string is: AT&F&C1S37=9S0=2Q1&D0&W
&F – Restore to factory default
&C1 – Carrier detect set to normal
S37=9 – Other than PC connection
S0=2 – Auto answer after 2 rings
&D0 – DTR ignored. Allows operation with DTE that does not provide DTR.
&W – Write config to memory
Hayes Accura 56K Model 4703US
The string is: AT&C1&D0&K4S0=1&W
&C1 – Carrier detect set to normal
&D0 – DTR ignored. Allows operation with DTE that does not provide DTR.
&K4 – Use XON/XOFF flow control
S0=1 – Auto answer after 1 ring
&W – Write config to memory
US Robotics Courier V.Everything 33.6/28.8
The string is: AT&F2&C1&D0S0=1&W
&F2 – Load Software Flow Control template settings
&C1 – Carrier detect set to normal
&D0 – DTR ignored. Allows operation with DTE that does not provide DTR.
S0=1 – Auto answer after 1 ring
&W – Write config to memory
Dip Switch Settings
Dip Position Purpose
1 ON DTR Always On
2 OFF Verbal Result Codes
3 OFF Suppress Result Codes
4 OFF Echo Offline Commands
5 OFF Auto Answer ON RING
6 OFF NORMAL CARRIER DETECT
7 OFF DISPLAY ALL RESULT CODES
8 ON ENABLE AT COMMAND SET
9 ON NO DISCONNECT WITH +++
10 OFF LOAD NVRAM DEFAULTS
Contact your Extreme Technical Support representative and record the dial-in number for the analog line.
Contacting the ExtremeWorks Technical Assistance Center (TAC)
For additional assistance, please contact your local ExtremeWorks TAC.
Americas TAC (Corporate TAC)
Web site: www.extremenetworks.com/support/techsupport.asp
E-mail: support@extremenetworks.com
Toll free: 1-800-998-2408
Direct phone: 408-579-2826
3585 Monroe Street
Santa Clara, CA 95051
EMEA (Europe, Middle East & Asia) TAC
E-mail: support@extremenetworks.com
Direct phone: +31-30-8005000
Kernkade 2
Lageweide Ind. Park
3542 CH Utrecht
The Netherlands
Japan TAC
E-mail: support-j@extremenetworks.co.jp
Direct phone: +81-3-5842-4020
17F Sumitomo Korakuen Building
1-4-1 Koishikawa
Bunkyo-ku, Tokyo 112-002, Japan
>>>
© 2001 Extreme Networks, Inc. All rights reserved. Extreme Networks, BlackDiamond, Ethernet Everywhere, Extreme Ethernet Everywhere, ExtremeWare,
Summit, ServiceWatch and the color purple are registered trademarks of Extreme Networks, Inc. in certain jurisdictions. Alpine, Alpine 3804, Alpine 3808,
BlackDiamond 6808, BlackDiamond 6816, Extreme Standby Router Protocol, ESRP, Summit1i, Summit5i, Summit7i, Summit24, Summit48, Summit48i,
SummitGbX, SummitRPS, Epicenter, Extreme Velocity, the BlackDiamond logo, the Alpine logo, the Summit logo, the ExtremeWorks logo and the Extreme
Networks logo are trademarks of Extreme Networks, Inc., which may be registered or pending registration in certain jurisdictions. Extreme Turbodrive, the
Extreme Turbodrive logo, ExtremeWorks, ExtremeWorks Professional Services and Go Purple are service marks of Extreme Networks, Inc., which may be
registered or pending registration in certain jurisdictions. All other registered trademarks, trademarks and service marks are property of their respective
owners. Specifications are subject to change without notice. L-UG-MSC-111 Rev. November 2001
www.extremenetworks.com
3585 Monroe Street Santa Clara, CA 95051-1450 Phone 408.579.2800 Fax 408.579.3000
Otros manuales para Alpine 3804
4
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Cambiar de Extreme Networks
Extreme Networks
Extreme Networks 8720 Manual
Extreme Networks
Extreme Networks Alpine 3802 Manual
Extreme Networks
Extreme Networks BlackDiamond 10808 Manual de usuario
Extreme Networks
Extreme Networks Summit X440 Series Manual de usuario
Extreme Networks
Extreme Networks ExtremeSwitching SLX 9150 Manual
Extreme Networks
Extreme Networks BlackDiamond X8 Series Instrucciones de montaje
Extreme Networks
Extreme Networks 7720 Manual de usuario
Extreme Networks
Extreme Networks BlackDiamond 8800 Series Manual
Extreme Networks
Extreme Networks Extreme Management Center NMS-A-25 Manual de usuario
Extreme Networks
Extreme Networks X460-G2 Series Manual de usuario
Extreme Networks
Extreme Networks ExtremeSwitching 5320 Series Manual
Extreme Networks
Extreme Networks Summit 200-24 Manual de usuario
Extreme Networks
Extreme Networks Extreme Switching 3500 Series Manual de usuario
Extreme Networks
Extreme Networks BlackDiamond 10K Series Manual de usuario
Extreme Networks
Extreme Networks Summit X450a-24tDC Manual
Extreme Networks
Extreme Networks Summit X250e-24p Manual de usuario
Extreme Networks
Extreme Networks ExtremeSwitching SLX 9030 Series Manual
Extreme Networks
Extreme Networks ExtremeSwitching VDX 6740 Manual
Extreme Networks
Extreme Networks Summit X150 Series Manual
Extreme Networks
Extreme Networks Summit X620-16x Manual de usuario
