Extreme Networks X460-G2 Series Manual de instalación y operación

Part Number: 120889-00 Rev. 01

Summit X460-G2 Series Switches

Installation Note

Pre-installation Requirements

Before you install the Summit X460-G2 series switch, read the information in “Safety Information” on

page 2.

The following items are provide with the Summit X670 series switch:

●Mounting brackets

●Eight M3 screws to secure the mounting brackets to the switch

To install the switch in a rack, you need the following additional tools and equipment:

●Four rack mounting screws to match your equipment rack

●Screwdriver to fit the rack mounting screws

●AC power cord that is suitable for the current rating of this product (See “Selecting AC Power

Supply Cords” on page 4.

Required Tools

The following items are provided with the Summit X460-G2 series switch:

●Two rack mounting brackets adaptable for either a front-mount or mid-mount installation

●Twelve screws for attaching the brackets to the switch enclosure

●For DC models, spade terminal and M4 screw with captive washer for grounding the switch

You need the following additional tools and materials to install the switch in a rack:

●#1 Phillips screwdriver

●Four rack mounting screws to match your equipment rack

●Screwdriver to fit the rack mounting screws

●#14 AWG stranded copper cable for grounding the switch (DC powered models)

●ESD-preventive wrist strap for installing optional ports at the back of the switch

Installing the Switch

Summit X460-G2 Series Switches Installation Note

Installing the Switch

1On each side of the switch, place a mounting bracket over the mounting holes.

2Insert the provided screws and tighten them securely (Figure 1).

Figure 1: Attaching a Mounting Bracket

3Slide the switch into the rack (Figure 2).

Figure 2: Installing the Switch in the Rack

4Insert and tighten rack-mounting screws to secure the switch to the rack.

5Connect the power cable to the AC input power connector on the back of the switch.

6Connect the other end of the power cable to an AC power socket.

Safety Information

WARNING!

Read the safety information in this section before you install Extreme Networks products. Failure to follow

this safety information can lead to personal injury or damage to the equipment.

SH_262

Maintenance Safety

Summit X460-G2 Series Switches Installation Note

Only trained service personnel should perform service to Extreme Networks switches and components.

Trained service personnel have read all related installation manuals, have the technical training and

experience necessary to be aware of the hazards to which they are exposed in performing a task, and

are aware of measures to minimize the danger to themselves or other persons.

WARNING!

This is a Class A product. In a residential environment this product may cause radio interference, in which

case the user may be required to take adequate measures.

Considerations Before Installing

●The system is designed to operate in a typical Telco environment that is environmentally controlled.

Choose an indoor area that has the following characteristics:

- Temperature-controlled and humidity-controlled, to ensure that the maximum ambient room

temperature shall not exceed the temperature specified in the product data sheet

- Clean and free from airborne materials that can conduct electricity

- Well ventilated and away from sources of heat, including direct sunlight

- Away from sources of vibration or physical shock

- Isolated from strong electromagnetic fields produced by electrical devices

- Secured, enclosed, and restricted-access, ensuring that only trained and qualified service

personnel have access to the equipment

●Establish at least 3 inches clearance on all sides for effective ventilation. Do not obstruct air intake

vents or ventilation grills on the front, side, or rear panel. Locate the system away from heat sources.

●Make sure that your equipment is placed in an area that accommodates the product specifications

for power consumption and component heat dissipation.

●Make sure that your power supplies meet the site power or AC power requirements of all network

equipment.

Maintenance Safety

●Use only original accessories or components that are approved for use with this system.

Failure to follow these instructions may damage the equipment or violate required safety and

EMC regulations.

●The chassis cover should be removed only by Extreme Networks personnel. This system contains no

customer-serviceable components. Repairs to the system must be performed by an Extreme

Networks factory service technician.

●Disconnect all power cords before working near power supplies, unless a maintenance procedure

instructs you to do otherwise.

●Replace a power cord immediately if it shows any signs of damage.

●When you work with optical devices or other modular accessories, wear an ESD-preventive wrist

strap to reduce the risk of electronic damage to the equipment. Connect the other end of the strap to

an appropriate grounding point on the equipment rack. Leave the ESD-preventive wrist strap

Maintenance Safety

Summit X460-G2 Series Switches Installation Note

permanently attached to the equipment rack so that it is always available when you need to handle

ESD-sensitive components.

●Install all cables in a manner that avoids strain. Use tie wraps or other strain relief devices.

General Safety Precautions

●Do not try to lift objects that you think are too heavy for you.

●When you install equipment in a rack, load heavier devices in the lower half of the rack first to

avoid making the rack top-heavy.

●For Summit desktop equipment installations, do not place a monitor or other heavy objects on top of

the equipment. The chassis cover is not designed to support weight.

●Use only tools and equipment that are in perfect condition. Do not use equipment with

visible damage.

●Route cables in a manner that prevents possible damage to the cables and avoids causing accidents,

such as tripping.

Selecting AC Power Supply Cords

Extreme Networks does not include AC power input cords in the product box. To purchase a power

cord for your product and for your specific country, contact your local Extreme Networks Channel

Account Manager or Sales Manager, or purchase a cord from your local supplier.

To locate a Sales Manager or Partner in your region visit:

http://www.extremenetworks.com/how-to-buy/how-to-buy.aspx

Power cords that are used with AC-powered Summit X460-G2 series switches must meet the

following requirements:

●The power cord must be agency-certified for the country of use.

●The power cord must have an IEC320-C13 connector for connection to the switch or external power

supply.

●The power cord must have an appropriately rated and approved wall plug applicable to the country

of installation.

●For cords up to 6 feet (2 m) long, the wire size must be 18 AWG (.75 mm2) minimum; over 6 feet, the

minimum wire size is 16 AWG (1.0 mm2).

Connecting Power

For the specific ratings and input power requirements of each switch model, see the data sheet for the

Summit X460-G2 series switches at http://www.extremenetworks.com.

WARNING!

Be sure to satisfy the requirements listed in this section when you connect all Extreme Networks

equipment to power.

Maintenance Safety

Summit X460-G2 Series Switches Installation Note

AC powered Summit X460-G2 switches

When you connect equipment to power:

●Plug power cords only into properly grounded electrical outlets to help prevent electrical shock and

to comply with international safety standards.

●Use only power cords that are certified for use within the country of use. Do not attempt to modify

AC power cords.

●Make sure the voltage and frequency of your power outlet match the system electrical ratings for the

equipment. The building and/or power source must provide overload protection.

●Use a surge suppressor, line conditioner, or uninterruptible power supply to protect the system from

momentary increases or decreases in electrical power.

●Summit X460-G2 series switches do not have switches for turning the unit on and off. Remove the

wall plug from the electrical outlet to disconnect the power from a Summit X460-G2 series switch.

Make sure that this connection is near the equipment and is easily accessible for quick disconnect.

WARNING!

Make sure that the source outlet is properly grounded according to the country’s local electrical

requirements before plugging the AC supply power cord into a power supply.

Cable Routing for LAN Systems

The Summit X460-G2 series switches meet the requirements for LAN system equipment. LAN systems

are designed only for intra-building installations; that is, cable runs between devices must be in the

same building as the connected units.

Fiber Optic Ports—Optical Safety

The following safety warnings apply to all optical devices used in Extreme Networks equipment that

are removable or directly installed in an I/O module or chassis system. Such devices include but are

not limited to gigabit interface converters (GBICs), small form factor pluggable (SFP) modules (or

mini-GBICs), XENPAK transceivers, and XFP laser optic modules.

WARNING!

Laser optic modules become very hot after prolonged use. Be careful when you remove a laser optic

module from the chassis or option card. If the laser optic module is too hot to touch, disengage the laser optic

module and allow it to cool before removing it completely.

WARNING!

When you work with laser optic modules, always take the precautions listed below to avoid exposure to

hazardous radiation.

Battery Replacement and Disposal

Summit X460-G2 Series Switches Installation Note

●Never look at the transmit LED/laser through a magnifying device while the laser is powered on.

●Never look directly at a fiber port on the switch or at the ends of a fiber cable when they are

powered on.

●Invisible laser radiation can occur when the connectors are open. Avoid direct eye exposure to the

beam when optical connections are unplugged.

●Never alter, modify, or change an optical device in any way other than suggested in this

document.

Battery Replacement and Disposal

Batteries included with Extreme products are encapsulated and must be replaced only by qualified

Extreme Service personnel. Contact your Extreme Networks Service personnel for product replacement.

Do not attempt to replace the battery. If these instructions are disregarded and replacement of these

batteries is attempted, the following guidelines must be followed to avoid danger of explosion:

●Replace with the same or equivalent battery type as recommended by the battery manufacturer.

●Dispose of the battery in accordance with the battery manufacturer’s recommendation.

Battery Warning — Taiwan

WARNING!

Disconnect Device Requirement

WARNING!

A readily accessible disconnect device shall be incorporated in the building installation wiring.

Un dispositif de déconnexion facilement accessible doit être incorporé dans l'installation électrique du bâtiment.

Fiber Optic Ports and Optical Safety

Summit X460-G2 Series Switches Installation Note

Fiber Optic Ports and Optical Safety

The following safety warnings apply to all optical devices used in Extreme Networks equipment that

are removable or directly installed in an I/O module or chassis system. Such devices include but are not

limited to gigabit interface converters (GBICs), small form factor pluggable (SFP) modules (or

mini-GBICs), QSFP+ modules, XENPAK transceivers, and XFP laser optic modules.

WARNING!

Laser optic modules become very hot after prolonged use. Take care when removing a laser optic module

from the module or option card. If the laser optic module is too hot to touch, disengage the laser optic module and

allow it to cool before removing it completely.

WARNING!

When working with laser optic modules, always take the precautions listed below to avoid exposure to

hazardous radiation.

●Never look at the transmit LED/laser through a magnifying device while the transmit LED is

powered on.

●Never look directly at a fiber port on the switch or at the ends of a fiber cable when they are

powered on.

●Invisible laser radiation can occur when the connectors are open. Avoid direct eye exposure to the

beam when optical connections are unplugged.

●Never alter, modify, or change an optical device in any way other than suggested in this

document.

GBIC, SFP (Mini-GBIC), QSFP+, XENPAK, and XFP Regulatory

Compliance

Extreme Networks pluggable optical modules and direct-attach cables meet the following regulatory

requirements:

●Class 1 or Class 1M Laser Product

●EN60825-1:2007 2nd Ed. or later, European standard

●FCC 21 CFR Chapter 1, Subchapter J in accordance with FDA & CDRH requirements

●Application of CE Mark in accordance with 2004/108/EEC EMC Directive and the 2006/95/EC Low

Voltage Directives

●UL and/or CSA registered component for North America

●47 CFR Part 15, Class A when installed into Extreme products

Canada Warnings

Summit X460-G2 Series Switches Installation Note

Canada Warnings

WARNING!

Disconnect all power supply cords before servicing.

Débranchez tous les cordons d'alimentation avant l'entretien.

WARNING!

A dedicated Listed circuit breaker rated at 20A is to be used for each power supply connection.

Un disjoncteurListed dédié évalué à 20A doit être utilisée pour chaque connexion d'alimentation .

WARNING!

Extreme Networks power supplies do not have switches for turning the unit on and off. Disconnect all

power cords to remove power from the device. Make sure that these connections are easily accessible.

Extreme Networks alimentations n'ont pas de contact pour mettre l'appareil sous et hors tension . Débranchez tous

les cordons d'alimentation pour couper l'alimentation de l'appareil. Assurez-vous que ces connexions sont

facilement accessibles.

NOTE

The site must have secured, enclosed, and restricted-access, ensuring that only trained and qualified

service personnel have access to the equipment.

Le site doit avoir obtenu , clos , et à accès restreint , assurant que seul un personnel formé et qualifié avoir accès à

l'équipement.

WARNING!

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Conformity Statements for EMC Class A

WARNING!

This is a Class A product. In a residential environment this product may cause radio interference, in which

case the user may be required to take appropriate measures.

Conformity Statements for EMC Class A

Summit X460-G2 Series Switches Installation Note

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case you are required to

correct the interference at your own expense.

Japan (VCCI Class A)

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a

domestic environment, radio interference may occur, in which case the user may be required to take

corrective actions.

Taiwan Warnings

Korea EMC Statement

警告:此为A级产品，在生活环境中，该产品可能造成

线电干扰。在这种情下，可能需要用户对干扰采取切

实可行的措施。

Conformity Statements for EMC Class A

Summit X460-G2 Series Switches Installation Note

Otros manuales para X460-G2 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Extreme Networks

Extreme Networks

Extreme Networks Summit Summit48si Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching VSP 7400 Series Manual

Extreme Networks

Extreme Networks ISW Series Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond 8806 Manual

Extreme Networks

Extreme Networks VSP 4900 Series Manual

Extreme Networks

Extreme Networks X460-G2 Series Manual de usuario

Extreme Networks

Extreme Networks Hubs & Switches Instrucciones de instalación

Extreme Networks

Extreme Networks Summit Summit24 Manual de usuario

Extreme Networks

Extreme Networks Summit X150 Series Manual

Extreme Networks

Extreme Networks ExtremeSwitching SLX 9540 Manual

Extreme Networks

Extreme Networks Summit X150 Series Manual de usuario

Extreme Networks

Extreme Networks 8520 Series Manual

Extreme Networks

Extreme Networks Summit WM100 Manual de usuario

Extreme Networks

Extreme Networks Summit WM3000 Series SW v5.1 Manual

Extreme Networks

Extreme Networks Alpine 3800 FM-24MFi Manual

Extreme Networks

Extreme Networks Summit X450a-24tDC Manual

Extreme Networks

Extreme Networks Summit X150 Series Manual de instalación y operación

Extreme Networks

Extreme Networks Summit X650 Series Manual de usuario

Extreme Networks

Extreme Networks Summit X670-G2-72x Manual de usuario

Extreme Networks

Extreme Networks Summit X620-16x Manual de usuario

Extreme Networks

Extreme Networks BlackDiamond 10K Series Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching SLX 9140 Manual

Extreme Networks

Extreme Networks Summit 200-24 Manual de usuario

Extreme Networks

Extreme Networks ExtremeSwitching SLX 9030 Series Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario