Extech Instruments PH100 Manual de usuario

USER GUIDE

ExStikTM Waterproof pH Meters

Models PH100 and PH110

Patent Pending

PH100/PH110-en-GB_v3.1 3/15

Introduction

Thank you for selecting the Extech Model PH100 and/or the model PH110 (refillable) meter. This

instrument is designed for high accuracy pH testing. This device is shipped fully tested and calibrated

and, with proper use, will provide years of reliable service. Please visit our website (www.extech.com)

to check for the latest version of this User Guide, Product Updates, Product Registration, and

Customer Support. 

PH100/PH110-en-GB_v3.1 3/15

ExStikTM Description

Front Panel Controls

1. Battery compartment cap

2. LCD Display

3. MODE / HOLD button

4. CAL / RECALL button

5. ON/OFF button

6. Electrode collar

7. Electrode (refillable)

(Electrode cap is not shown)

Display

1. Bargraph reading

2. Measurement reading

3. BAT (low battery) and

HOLD (data hold) indicators

4. Temperature display

5. Bargraph scale designations

6. Units of measure

7. Calibration indicators

8. RENEW and CAL indicators

CAUTIONS

This device is not a toy and must not reach children’s hands. It contains hazardous objects as

well as small parts that the children could swallow. In case a child swallows any of them,

please contact a physician immediately

Do not leave batteries and packing material lying around unattended; they can be dangerous

for children if they use them as toys

In case the device is going to be unused for an extended period of time, remove the batteries

to prevent them from draining

Expired or damaged batteries can cause cauterization on contact with the skin. Always, use

suitable hand gloves in such cases

See that the batteries are not short-circuited. Do not throw batteries into the fire.

PH100/PH110-en-GB_v3.1 3/15

Overview

pH Overview

pH is a unit of measure (ranging from 0 to 14pH) indicating the degree of acidity or alkalinity of a

solution. pH tests are the most commonly performed measurements in water analysis and reports

the negative log of the hydrogen ion activity of a solution which is an indicator of acidity or alkalinity.

Solutions with a pH less than 7 are considered acidic, solutions with a pH higher than 7 are known

as bases, and solutions with a pH of exactly 7 are neutral.

The pH scale is logarithmic so, for example, if sample A is 1 pH less than Sample B, this means that

Sample A is 10 times more acidic then Sample B. A difference of 1 pH represents a ten-fold

difference in acidity.

Getting Started

For new meters, remove the battery cap and then remove the battery insulating strip.

Remove the cap from the bottom of the ExStikTM to expose the electrode glass surface and

reference junction

Before first use or after extended storage, soak the electrode (with its cap removed) in a pH 4

solution for about 10 minutes

White KCL crystals may be present in the cap. These crystals will dissolve in the soak or they can

be simply rinsed with tap water

Always calibrate close to the expected measurement value

A sponge is located in the electrode protective cap. Keep this sponge soaked with a pH 4 solution

to preserve Electrode life during storage

Replacing Electrodes

The ExStikTM is shipped with an electrode attached. Electrode life is limited and is dependent on

(among other factors) frequency of use and care. If the electrode needs to be replaced, follow these

steps for removing and connecting electrodes. Note that the PH110 has a refillable electrode.

1. To remove an electrode, unscrew and completely remove the electrode retaining collar.

2. Gently rock the electrode from side to side, pulling it away from the meter, until it disconnects.

3. To attach an electrode, carefully plug the electrode into the meter socket (note that the

electrode connector is keyed, ensuring proper connection).

4. Secure the electrode in place by tightly turning the collar in place. (a rubber gasket seals the

electrode with the meter).

Automatic Electrode Recognition

When the ExStikTM is turned on, it recognizes the type of electrode that is connected and displays

the appropriate unit of measure. Attach electrode before turning the ExStikTM on.

Powering the ExStik™

If the batteries are weak, the ‘BAT’ indicator appears on the LCD. Press the ON/OFF key to turn the

ExStikTM on or off. The auto power off feature shuts the ExStikTM off automatically after 10 minutes

of inactivity to preserve battery life.

PH100/PH110-en-GB_v3.1 3/15

Operation

Overview

When the electrode is placed in a solution, the main display and bargraph indicate the pH reading

while the lower display reads temperature (readings flash until they have stabilized). The bargraph

is ‘center zero’, i.e. at pH 7 there is no display. As the pH rises, the bar moves from the center to the

right. If the pH drops, the bar moves from the center to the left.

pH Calibration (1, 2, or 3 points)

A two point calibration with a buffer of 7 plus 4 or 10 (whichever is nearest to the expected sample

value) is always recommended. A one point calibration (choose the value closest to the expected

sample value) is also valid. For best accuracy, always calibrate at the sample temperature.

1. Place the electrode into a buffer solution (4, 7, or 10) and momentarily press the CAL key. pH

7 should be calibrated first, then 4 and/or 10 pH.

2. The ExStikTM automatically recognizes the solution and calibrates itself to that value. Note: If

the solution is more than 1pH off from the 4, 7, or 10pH standard, the ExStikTM will assume an

error and abort the calibration. CAL and END will be displayed.

3. During calibration, the pH reading flashes on the main display.

4. When calibration is complete, the ExStikTM automatically displays ‘END’ and returns to normal

operation mode.

5. The appropriate circled indicator ➃,➆, or ➉will appear on the LCD when a calibration has

been completed. The calibration data is stored until a new calibration is performed.

6. For a two or three point calibration, repeat steps 1-4.

Note: Always turn the meter off and then on before calibrating to allow sufficient time to complete

the calibrations during one power cycle. If the meter auto powers off during calibration the

calibrations remain valid, but new calibrations will turn the circled indicators off.

Note: The Automatic Temperature Compensation (ATC) circuit is not active during calibration. To

ensure a more accurate calibration, make sure that the calibration buffers are at 25°C (77°F).

RESET

If the meter will not calibrate or displays a -1, reset the meter and attempt to re-calibrate.

1. Turn off the meter.

2. Remove the battery cartridge from the top of the meter.

3. Press the On/Off button for 10 seconds to bleed off all charges within the meter.

4. Re-insert the batteries and power on the meter.

5. Attempt to re-calibrate the meter.

Changing the Displayed Temperature Units

Press and hold the CAL button for approx. 3 seconds. The oC or oF icon will change first and the

numerical temperature value will change after the button is released. If the Calibration mode is

accidentally accessed ‘CAL’ appears on the LCD. Simply turn the ExStikTM off and start again.

Data Hold

Momentarily press the MODE button to freeze the current reading. The HOLD display icon will

appear along with the held reading. The held reading will also be stored in memory. Momentarily

press the MODE key to return to normal operation.

PH100/PH110-en-GB_v3.1 3/15

15-Storing Readings into Memory

1. Momentarily press the MODE button to store a reading.

The LCD will briefly display the memory location

number and then the value stored (Data Hold will

activate).

2. Momentarily press MODE again to return to normal

operation.

3. Repeat step 1 to store the next reading and so on.

4. After 15 readings are stored the ExStikTM will return to memory location 1 and start overwriting

existing data with newly stored data.

Recalling Stored Readings

Note: Check that the HOLD symbol is not displayed. If it is, exit the HOLD function by momentarily

pressing the MODE button.

1. Momentarily press the CAL button and then press the MODE button immediately after CAL is

displayed; the storage location number (1 through 15) will flash. If the CAL mode is

accidentally accessed (display flashing), press the CAL button again to exit.

2. The last reading stored will be displayed first. To advance through the stored readings,

momentarily press the MODE button. The location number is displayed first, followed by the

reading stored in that location.

3. To exit the recall mode, momentarily press the CAL button and the ExStikTM will return to

normal operation.

CAL Reminder Display

When the ExStikTM is turned on in the pH mode for the 15th time without recalibration, the ‘CAL’ icon

appears on the LCD indicating that the ExStikTM may require calibration. Some applications may

require recalibration of the electrode more frequently than others. The CAL display is simply a

reminder and will turn off when the pH electrode is recalibrated.

RENEW Display

A flashing ‘RENEW’ warning indicates that the probe may be nearing the end of its useful life. If

cleaning or recalibration does not cause the RENEW icon to disappear, replace the electrode. The

RENEW display appears when the output of the pH electrode fails a diagnostic test.

Considerations

If the unit appears to be locked (display frozen) it is possible that the Data Hold mode has been

inadvertently accessed by pressing the MODE button. Simply press the MODE button again or

turn the meter off and restart if the display appears frozen.

If the meter does latch up and no button presses revive it, remove the batteries, push the ON

button for 10 seconds and then reinsert the batteries.

Note that if the batteries are removed, any stored readings will be discarded. Also, the user

calibration data for pH will be cleared. New user pH calibration data is required. Factory

calibration data for all models will be retained, however.

PH100/PH110-en-GB_v3.1 3/15

Battery Replacement

1. Twist off the battery compartment cap

2. Replace the four (4) 2032 batteries observing polarity.

3. Replace the battery compartment cap

Never dispose of used batteries or rechargeable batteries in household waste.

As consumers, users are legally required to take used batteries to appropriate

collection sites, the retail store where the batteries were purchased, or wherever

batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-of-

life devices to a designated collection point for the disposal of electrical and electronic equipment.

Other Battery Safety Reminders

oNever dispose of batteries in a fire. Batteries may explode or leak.

oNever mix battery types. Always install new batteries of the same type.

pH Electrode Refilling (pH110/115 refillable electrode only)

The refillable electrode does not need to be detached from the body of the

ExStikTM in order to perform the refilling procedure. Refillable electrodes

(PH115) have a removable reference junction (slotted) and the word

REFILLABLE on the side of the electrode housing.

Removing the Reference Junction

The removal tool supplied with the PH113

Refill Kit is used to remove the reference

junction from the sensing surface of the

electrode. If the reference junction does not

have slots for the ‘teeth’ of the removal tool to

lock onto, the electrode is NOT refillable.

Holding the electrode upside down, unscrew

and remove the reference junction using the

removal tool.

Filling the Electrode

1. Once the reference junction is removed, fill the cavity with the refill solution supplied in

the Refill Kit.

2. Replace the reference junction using the removal/installation tool. (Spare junctions are

provided if needed).

Filling Solution

The supplied container includes 15ml of filling solution. There is enough solution for 4 to 5 refills.

Use only the supplied solution for refilling the electrode.

Refillable

pH Module

Reference junction

Junction removal tool

PH100/PH110-en-GB_v3.1 3/15

Specifications

Display Multifunction LCD with Bargraph

Operating conditions 32 to 122oF (0 to 50oC) / < 80% RH

Range and Accuracy 0.00 to 14.00 / ± 0.01pH typical

Temp. Compensation Automatic from 32 to 194oF (0 to 90oC)

Temperature Range 23 to 194oF (-5 to 90oC)

Temperature Resolution 0.1oup to 99.9 then 1othereafter

Temperature Accuracy ± 1oC/1.8oF [from -5 to 50oC (23 to 122oF)]

± 3oC/5.4oF [from 50 to 90oC (122 to 194oF)]

Measurement storage 15 tagged (numbered) readings

Power Four (4) CR2032 button batteries

Low battery indication ‘BAT’ appears on the LCD

Auto power off After 10 minutes of inactivity

Dimensions 1.4x6.8x1.6”(35.6x172.7x40.6mm); 3.85oz (110g)

Optional Accessories

Tripak buffers with 4, 7 & 10 pH capsules (6 each) plus two rinsing solutions (Part Number:

PH103)

pH 4.01 buffer, pint, (Part Number PH4-P)

pH 7.00 buffer, pint, (Part Number PH7-P)

pH 10.00 buffer, pint, (Part Number PH10-P)

Spare pH Electrode – non-refillable (Part Number: PH105)

Spare pH Electrode - refillable (Part number PH115)

Electrode Refill solution (Part number PH113)

Spare ORP electrode (Part Number: RE305)

Spare Chlorine electrode (Part Number: CL205)

Weighted base with 5 solution cups (Part Number: EX006)

Note: If the unit is to be converted for ORP or Chlorine use by attaching the proper electrode,

please visit www.extech.com to download the proper User Guide

Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments HD450 Manual de usuario

Extech Instruments

Extech Instruments Oyster 341350A-P Manual de usuario

Extech Instruments

Extech Instruments RH300 Manual de usuario

Extech Instruments

Extech Instruments CO250 Manual de usuario

Extech Instruments

Extech Instruments RPM10 Manual de usuario

Extech Instruments

Extech Instruments SDL400 Manual de usuario

Extech Instruments

Extech Instruments SDL550 Manual de usuario

Extech Instruments

Extech Instruments FHT200 Manual de usuario

Extech Instruments

Extech Instruments EC210 Manual de usuario

Extech Instruments

Extech Instruments 461891 Manual de usuario

Extech Instruments

Extech Instruments SDL800-NIST Manual de usuario

Extech Instruments

Extech Instruments 451212 Manual de usuario

Extech Instruments

Extech Instruments AN100-NIST Manual de usuario

Extech Instruments

Extech Instruments TB400 Manual de usuario

Extech Instruments

Extech Instruments 407730 Manual de usuario

Extech Instruments

Extech Instruments DT500 Manual de usuario

Extech Instruments

Extech Instruments HD755 Manual de usuario

Extech Instruments

Extech Instruments HD350 Manual de usuario

Extech Instruments

Extech Instruments SDL310 Manual de usuario

Extech Instruments

Extech Instruments RPM40 Manual de usuario

Extech Instruments

Extech Instruments PQ3450-30 Manual de usuario

Extech Instruments

Extech Instruments ExStik EC510 Manual de usuario

Extech Instruments

Extech Instruments LT300 Manual de usuario

Extech Instruments

Extech Instruments MO270 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario