Extech Instruments Oyster Series Manual de usuario

USER GUIDE

pH/mV/Temperature Meter

Model OYSTER-10

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

Introduction

Congratulations on your purchase of Extech's Oyster Series splash-proof meter. This microprocessor-

based device with tactile buttons simultaneously displays pH or mV and Temperature (oC/oF

selectable).

The device can store 25 labeled readings for recall at a later time. The Oyster 10 is battery operated,

portable, and includes a hinged display that can be adjusted to any viewing angle. In addition, the

neck-strap offers hands-free operation.

Advanced features include diagnostic displays, MIN/MAX readings, audible alerts, 5-point buffer

recognition, & Auto/Manual temperature compensation.

This instrument is shipped fully tested and calibrated and, with proper use, will provide years of reliable

service. Please visit the Extech Instruments website (www.extech.com) to check for the latest version

of this User Guide. Extech Instruments is an ISO-9001 certified company.

Meter Description

1. LCD Display

2. Battery compartment (9V battery)

3. Function buttons (Power, Up/Down, Max/Min, pH/mV, Store/Recall)

4. AC Adapter input (117VAC)

5. RTD Temperature probe input (3.5mm phono jack)

6. BNC style pH/mV electrode input

7. Neck-strap loop (2)

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

pH Overview

pH is a unit of measure (ranging from 0 to 14pH) indicating the degree of acidity or alkalinity of a

solution. pH tests are the most commonly performed measurements in water quality testing, using

the hydrogen ion activity of a solution to determine acidity or alkalinity. Solutions with a pH less than

7 are considered acidic, solutions with a pH higher than 7 are known as bases, and solutions with a

pH of exactly 7 are considered neutral.

The pH scale is logarithmic, so, for example, if sample A is 1 pH less than Sample B, this means

that Sample A is 10 times more acidic then Sample B. A difference of 1 pH represents a ten-fold

difference in acidity.

ORP/REDOX Overview

ORP stands for Oxidation Reduction Potential and represents the oxidizing or reducing nature of a

solution. The overall “reactive” tendency of a solution can be determined from ORP measurements.

ORP testing is becoming more common in waste-water and water treatment measurement

regimens. The unit of measurement for ORP is mV.

Calibration and Operation

pH Calibration (ORP does not require calibration)

Before accurate measurements can be made, it is necessary to perform a 3-point calibration of the

meter with its electrode. Calibrate to a pH 7 buffer first, followed by a pH 4 (or 1.68) buffer and then

a pH 10 (or pH 12.45) buffer. The meter automatically recognizes the buffers listed in the table

below and calibrates itself to the buffer’s pH value.

1. Connect the pH electrode to the meter’s BNC connector input.

2. Open the top half of the meter to an appropriate viewing position.

3. Power the meter with the POWER/CAL button.

4. Place the electrode into a buffer solution.

5. Press and hold the CAL key until the CAL display icon appears.

6. During calibration, ‘CAL’ is shown on the display followed by ‘SA’ (saved).

7. When calibration is complete, the meter automatically displays ‘END’ and returns to the normal

operation mode. Repeat steps 1-5 as necessary. Note that it is not necessary to turn the meter

off and then back on again to calibrate each reference.

Error Message Note: The meter will display ‘E13’ if a calibration step fails. Try the calibration again

if ‘E13’ is displayed. The most common reason for the error is inaccurate or stale buffer solutions.

pH reading Range of measurement

1.68 0.00 to 1.68

4.00 1.68 to 6.50

7.00 6.50 to 7.50

10.00 7.50 to 12.45

12.45 12.45 to 14.00

Electrode note: Since pH electrodes can vary in performance, this meter displays an electrode’s

slope in %. For example, if two electrodes (one new and one moderately used) are calibrated in the

same pH 4 solution they’ll both display pH 4 on the meter. This is because the meter will accept one

pH value for a range of measurement values as shown in the table above (in this case, any reading

between 1.68pH and 6.50pH will be accepted as 4pH calibration). The meter then displays the

slope % for the electrode under test. If the slope % is below 75% or above 125%, the electrode

must be replaced. A slope of 100% is ideal.

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

pH Measurement and Temperature Compensation

1. Use the pH/mV button to select the pH mode. The unit of measure appears on the LCD.

2. Connect the pH electrode to the meter and place the sensor end in the solution under test.

3. For automatic temperature compensation, connect the temperature probe to the meter (display

will read ATC) and place the sensor end in the solution about 1/3 of the way below the solution

surface. The temperature reading of the solution appears on the bottom of the LCD. When the

temperature of a sample differs from a buffer solution temperature, allow enough time for the

electrode to stabilize to the sample's temperature.

4. For manual temperature compensation, a temperature sensor is not connected to the meter.

(MANUAL is displayed). A manual thermometer will be needed to determine the solution

temperature first.

Adjust the meter’s temperature display with the up/down buttons so that the displayed

temperature matches the temperature of the solution.

5. To change the unit of measure for temperature (C to F or F to C), turn the unit OFF then

complete the following steps. Press and continue to hold the pH/mV button and then press and

hold the Power button. Release the pH/mV button first then release the power button. The LCD

reflects the unit of measure.

6. Read the pH measurement on the main display. An out of range reading is indicated by dashes

( ----- ).

7. When the test is complete, unplug the electrode and rinse it in distilled water.

8. Place approx. 1 ml of pH 4 solution in the wetting cap before replacing it.

mV (ORP) Measurements

1. Note that calibration is not required for mV (ORP) measurements.

2. Use the pH/mV button to select the mV mode. The display will reflect the unit of measure.

3. Remove the wetting cap from the ORP electrode and connect the cable via the BNC meter

connection.

4. Rinse the ORP electrode and place it into a sample solution. When the LCD stabilizes it will

read the redox potential of the sample in millivolts.

5. When sampling is complete, unplug and rinse the electrode. Place a small portion (1ml) of

distilled water in the wetting cap. Place the cap over the electrode.

25-Reading Measurement Storage

1. Press the STORE/RECALL button to store the current reading. Press each time a reading is to

be stored.

2. If an attempt is made to store more than 25 readings, the stored readings (starting with the first

reading) will be overwritten.

3. To recall readings, press and hold the STORE/RECALL button until the ‘RECALL’ icon appears

on the LCD. Use the up/down arrow buttons to scroll through the stored readings. Note that

‘NULL’ is displayed if there are no readings in memory.

4. To exit this mode, press and hold the STORE/RECALL button until the ‘RECALL’ icon

disappears.

5. To clear the contents of the memory press and hold the up and the down arrow buttons while

powering the meter on until the ‘CLr’ icon appears on the LCD. All 25 locations will be erased.

Note: Readings are stored in non-volatile memory (saved when the meter is turned off).

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

MAX/MIN Display

1. The meter memorizes the highest (MAX) and lowest (MIN) readings when prompted.

2. Press and hold the MAX/MIN button until both the MAX and MIN icons appear on the LCD. The

meter will now begin keeping track of the MIN and MAX readings.

3. To view MAX/MIN values, press the MAX/MIN button again; the meter automatically displays the

highest and lowest readings in succession and then returns to the MAX/MIN recording mode.

4. To exit the MAX/MIN mode, press and hold the MAX/MIN button until the MAX and MIN icons

disappear.

5. To clear the MAX/MIN memory, cycle the meter power.

External Temperature Offset Adjustment

The Offset Adjustment is used to fine tune the temperature reading of the external temperature

probe. This procedure is for the external probe only when ATC is active.

1. Place the temperature probe into a known temperature and note any temperature reading error.

2. Simultaneously Press and Release the ▲and ▼buttons, 0.0 will appear on the LCD

temperature reading

3. .Press the ▲or ▼button to set the display equal to the error value determined in step 1.

4. Press the STORE button to save the offset value into memory,

5. Test the temperature probe in the know temperature source to verify the correction was proper

and the adjustment made in the correct direction.

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

pH Electrode Model 60120B Operation

The Following information applies to the Epoxy Body, Sealed Reference Combination pH Electrode

Model 60120B.

Electrode Considerations

1. The 60120B pH electrode is recessed in the polymer body allowing it to rest against the bottom

of a beaker without damaging the glass bulb. This eliminates the need for electrode holders and

allows the probe to be used as a stirring rod. This sealed reference design eliminates the need

for adding filling solutions (minimizing "dry-out") and can be used in up to 100 psig systems

without external pressurization.

2. The Electrode should remain in its bottle or cap until used.

3. If bubbles are seen in the bulb area, hold the electrode by its cap and shake downwards until

bubbles disappear.

4. To improve speed of response, vigorously stir the electrode in the sample, buffer, or rinse

solution.

5. After exposure to a sample, buffer, or rinse solution, shake the electrode with a snap motion to

remove residual drops of solution.

6. Use part of the sample/buffer to be tested next as a rinse solution whenever possible.

7. When calibrating, use a buffer as close as possible to the expected pH of the sample.

8. Keep buffers and samples at the same temperature to avoid temperature effects.

9. pH readings stabilize at various rates; allow time for readings to stabilize.

10. Electrodes deteriorate over time. If accuracy falls to 10% (slope), the electrode should be

cleaned. If no improvement is observed, replace the electrode.

Electrode Calibration and Cleaning

Refer to the earlier section ‘Calibration and Operation’ for calibration details. Refer to the section

below ‘Maintenance and Troubleshooting’ for details on electrode cleaning.

Electrode Storage

The electrode can be stored in the soaker bottle or wetting cap. For the storage bottle, slide the

cover onto the electrode, replace the O-ring, and insert electrode into the bottle firmly tightening the

cap. Ensure that the bottle or cap is filled with a pH 4 buffer solution.

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

Specifications

Range (Resolution) Accuracy

mV ± 1000 mV DC (1 mV) + 2mV

Temperature 32.0 to 212.0oF (0.0 to 99.9oC) + 0.8oF (0.5oC)

pH 0.00 to 14.00pH (0.01pH) + 0.02pH

Temperature Compensation 32 to 212oF (0-100oC) AUTO or MANUAL modes

Power 9 volt battery or optional AC adapter

Display Dual LCD display for simultaneous pH or mV and

temperature readings. LCD viewing angle: 90oto 180o

Over-range Indication Displays " ---- "

Power 9 volt battery or optional AC adapter

Auto Power OFF After 10 minutes of inactivity

Low Battery Indication Battery icon appears on LCD

Operating Temperature 41ºF to 104ºF (5ºC to 40ºC)

Storage Temperature - 4oF to 140oF (-20oC to 60oC)

Operating Humidity Max 80% up to 87ºF (31ºC) decreasing linearly to 50% at

104ºF (40ºC)

Storage Humidity <80%

Operating Altitude 7000ft. (2000meters) maximum

Dimensions / Weight 3.75 x 4.25 x 2" (96 x 108 x 45mm) / 12 oz (340g)

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

Maintenance and Troubleshooting

Electrode Cleaning

The type of electrode coating that occurs over time will determine the cleaning method. Soft

coatings can be removed by vigorous stirring or by using a squirt bottle. Organic chemical coating

(hard coatings) should be chemically removed. Only in extreme cases should the bulb be cleaned

mechanically.

Battery Replacement

Install a new battery when the low battery indicator appears on the LCD.

1. Open the calibrator’s lid as far as possible.

2. Open the battery compartment using a coin at the arrow indicator.

3. Replace the battery and close the cover.

Battery Safety Reminders

Please dispose of batteries responsibly; always observe local, state, and federal regulations

with regard to battery disposal.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

Troubleshooting the Meter

Meters are the least likely cause of pH measurement problems. To rule out the meter check the

following:

1. Check the 9V battery and replace it if necessary.

2. When using the AC adaptor for power, check that the line cord is firmly connected to the meter.

3. Replace the existing electrode connector with optional BNC shorting plug (shorts the ground

ring to the center pin of the meter’s BNC jack) and check the following:

a) Set the measurement mode to pH. The LCD reading should be stable.

b) Adjust the calibration control for an LCD reading of 7.00.

c) Change to the mV measurement mode. The LCD should read 0 mV.

d) Note that an out of range reading is indicated by dashes ( -------).

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

Troubleshooting an Electrode Problem

Symptom Cause Recommended Solution

Long response time or

reading drift

Clogged Junction Soak in 4.07 M Potassium Chloride (KCl)

@ 60oC for 30 minutes. Replace

electrode if necessary.

Strong Alkaline measurement Soak in 0.1 M HCL overnight

Deteriorated Gel layer of pH

sensing membrane

Replace electrode

Protein coating on electrode

surface

Soak in 1 gm Pepsin dissolved in 100ml

of 0.1 m HCL for 30 mins. or as needed

Oil, paint, dyes, suspended

solids on sensor

Rinse electrode alternately with materials

solvent (briefly) then a buffer 7.00

Organic solvents are coating

sensor

Organic mole fraction has to be less than

50% to assure reasonable readings. Limit

time of measurement. Keep probe in the

7.0 buffer between readings.

Dehydrated membrane Read solution for dry bulb below

Dry Bulb Long term storage without

wetting

Soak electrode tip in wetting cap filled

with 1ml 7.00 buffer for 24 to 48 hours

Static Charge Wiping electrodes Rinse electrode in 7.0 buffer and blot. Do

no wipe electrode.

Same readings in

different buffers and

samples

Cracked or broken bulb Replace electrode. Use bulb guard. Avoid

plunging electrode to bottom of container

and spinning bars. A wetting cap will

protect bulb between measurements.

Erratic LCD display Samples have low ionic

strength (lacks salt); e.g.

distilled, de-ionized, boiled,

lake water (high pressure)

For each 50 ml of sample add 1 drop

(50uL) of SAT.KCL No alteration in pH

will occur by inert KCL.

www.calcert.com sales@calcert.com1.888.610.7664 0

Oyster10-en-US_v2.3 9/15

Warranty

FLIRSystems,Inc.warrantsthisExtechInstrumentsbranddevicetobefreeofdefectsinpartsandworkmanshipforoneyear

fromdateofshipment(asixmonthlimitedwarrantyappliestosensorsandcables).Ifitshouldbecomenecessarytoreturnthe

instrumentforserviceduringorbeyondthewarrantyperiod,contacttheCustomerServiceDepartmentforauthorization.Visit

thewebsitewww.extech.comforcontactinformation.AReturnAuthorization(RA)numbermustbeissuedbeforeanyproductis

returned.Thesenderisresponsibleforshippingcharges,freight,insuranceandproperpackagingtopreventdamageintransit.

Thiswarrantydoesnotapplytodefectsresultingfromactionoftheusersuchasmisuse,improperwiring,operationoutsideof

specification,impropermaintenanceorrepair,orunauthorizedmodification.FLIRSystems,Inc.specificallydisclaimsanyimplied

warrantiesormerchantabilityorfitnessforaspecificpurposeandwillnotbeliableforanydirect,indirect,incidentalor

consequentialdamages.FLIR’stotalliabilityislimitedtorepairorreplacementoftheproduct.Thewarrantysetforthaboveis

inclusiveandnootherwarranty,whetherwrittenororal,isexpressedorimplied.

Calibration,Repair,andCustomerCareServices

FLIRSystems,Inc.offersrepairandcalibrationservicesfortheExtechInstrumentsproductswesell.NIST

certificationformostproductsisalsoprovided.CalltheCustomerServiceDepartmentforinformationon

calibrationservicesavailableforthisproduct.Annualcalibrationsshouldbeperformedtoverifymeter

performanceandaccuracy.Technicalsupportandgeneralcustomerserviceisalsoprovided,refertothe

contactinformationprovidedbelow.



Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

www.extech.com

SupportLines:U.S.(877)439‐8324;International:+1(603)324‐7800

TechnicalSupport:Option3;E‐mail:[email protected]

Repair&Returns:Option4;E‐mail:[email protected]

Productspecificationsaresubjecttochangewithoutnotice

Pleasevisitourwebsiteforthemostup‐to‐dateinformation

www.extech.com

FLIRCommercialSystems,Inc.,9TownsendWest,Nashua,NH03063USA

ISO9001Certified

www.calcert.com sales@calcert.com1.888.610.7664 0

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Extech Instruments

Extech Instruments

Extech Instruments 461750 Manual de usuario

Extech Instruments

Extech Instruments CO220 Manual de usuario

Extech Instruments

Extech Instruments UV505 Manual de usuario

Extech Instruments

Extech Instruments EC600 Manual de usuario

Extech Instruments

Extech Instruments CO230 Manual de usuario

Extech Instruments

Extech Instruments PH100 Manual de usuario

Extech Instruments

Extech Instruments HD450 Manual de usuario

Extech Instruments

Extech Instruments HD350 Manual de usuario

Extech Instruments

Extech Instruments EMF510 Manual de usuario

Extech Instruments

Extech Instruments DT300 Manual de usuario

Extech Instruments

Extech Instruments 380950 Manual de usuario

Extech Instruments

Extech Instruments HD700 Manual de usuario

Extech Instruments

Extech Instruments EC170 Manual de usuario

Extech Instruments

Extech Instruments MO230 Manual de usuario

Extech Instruments

Extech Instruments 461893 Manual de usuario

Extech Instruments

Extech Instruments 407768 Manual de usuario

Extech Instruments

Extech Instruments 475040 Manual de usuario

Extech Instruments

Extech Instruments EX622 Manual de usuario

Extech Instruments

Extech Instruments RH305 Manual de usuario

Extech Instruments

Extech Instruments 42265 Manual de usuario

Extech Instruments

Extech Instruments MO270 Manual de usuario

Extech Instruments

Extech Instruments 475055 Manual de usuario

Extech Instruments

Extech Instruments LT40 Manual de usuario

Extech Instruments

Extech Instruments RPM40 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario