EverFocus NeVio EAN900 Manual de usuario

EAN900

Installation Guide

Release: Jun. 2009 Ver. A

EAN900

This installation guide provides instructions for installing the EAN900 IP Camera. For

all other aspects of using this product, please refer to EAN900 User’s Manual, which

is available on the CD included in this package.

Installation steps

1. Confirm that all of the accessories have been supplied with the network camera

from the list below.

2. Confirm that your PC answers to the minimum computer requirements listed

below.

3. Setting up the hardware connection. Please see “Setting Up the Hardware

Connection” on page 4.

4. Network Connection. 3 typical types of network connection. Please see “Network

Connection” on page 7.

5. Set an IP address. Please see “Assign IP address” on page 9.

Package Contents

- Network camera (x1)

- Accessory packet (x1)

zC adaptor mount ring

zSD card cover bracket + 1 screw

zFixing block (fixes to back panel for holding power cable) + 2 screws

zHexagon wrench

EAN900

- Power adaptor (x1)

- Printed Installation Guide (x1)

- Software APs including user’s manual CD (x1)

Minimum Computer Requirements

-CPU: PC Pentium IV (2.0 GHz or higher) / AMD Athlon (or higher)

-VGA card: 32 MB min. 16.7 million colours, with DirectX9.0c support

-Memory: 512 MB RAM min., 1 GB HD space or above

Additional HD space depends on required local storage of video files,

100 Mbps network card

-Screen Resolution: 1024 x 768 pixels or higher, 32-bit pixel color resolution

-Operating system: Windows XP, service pack 3 or higher

-Software: DirectX9,0c, Internet Explorer 6.0 or higher

Note: Please connect to Microsoft’s Web Site for downloading.

For example: (This web site may change without notices.)

http://www.microsoft.com/downloads

EAN900

1. Setting Up the Hardware Connection

1. Mount a lens to the camera. (Megapixel lens recommended for high image

quality.)

2. Connect the EAN900 Network Camera to a PC with a Cat.5 cable.

○,1SD card: Slot to insert SD card.

○,2Video output: Loop through connection to the video signal from the Video In

connector. Terminated with a coaxial/BNC connector.

Note: 1. To see the image of video output, user must press Reset button for

about 35 seconds until the image is showed.

2. When switching to network video output, the camera power must be

○,

○

EAN900

re-plugged.

○,3Ethernet RJ-45 port: Connect to LAN via this standard RJ-45 connector.

Optional: This socket can also be used to power via PoE (Power over

Ethernet)

Yellow indicator light: On means 100Mbps, Off means 10Mbps.

Green indicator light: On means link, flicking means active, Off means link

fail.

○,4Reset: Loading factory default configuration by pressing the button, which is

inside this hole. Please insert the keen-edged device to the hole for 10 seconds.

○,5Power LED: There are five kinds of LED flash mode. The cycle of LED

flash is one second. The duration of each single bit is 0.1 second. LED display is

represented by number 0 & 1; 0 means light on, 1 means light off.

System Status LED Flash mode

Power ON 1111111111

Power OFF 0000000000

SD card formatting 1101100000

SD card is inserted 0111111111

Firmware updating 0101010101

○,6Alarm: Connect to Alarm In/Out device.

○,7RS485 (+-): Functionality reserved.

○,8GND: Ground pin.

○,9Power 12VDC: Connect with power adaptor.

○,10 Audio In: 3.5mm stereo socket for line-in signal.

○,11 Audio Out: It can be connected to an active speaker with a built-in amplifier

or a pair of headphones. A 3.5mm audio connector must be used for the audio out.

○,12 Microphone: A built-in microphone used to receive audio message.

○,13 Internal sensor: Day/Night switch sensor.

○,14 Auto iris lens connector

This connector is used to connect with the auto iris lens by a 4 pin male connector

Pin1 Pin2 Pin3 Pin4

DirectDrive Cnt- Cnt+ Drv+ Drv-

3. Power on the EAN900 via plug in the Adapter or via PoE (Power over

Ethernet).

3 2

EAN900

1.1 Terminal Connector Schematic Diagram

Terminal connector schematic diagram

EAN900

2. Network Connection

This section tells you how to do different types of network connections to IP cameras.

a. Router or LAN connection

This is the most common connection that allows multiples PC to see IP cameras/

video servers in pre-existing LAN through a router.

By doing port forwarding, you can view camera outside of internal LAN on internet.



b. Direct High Speed Connection

Direct High Speed Connection connect camera directly to modem without a router.

You need to assign the IP address you obtain from internet service provider to IP

camera/ Encoder. To access the camera, just type http:// IP address of your internet

provider. If you have a dynamic IP address, this connection does not work for you.

EAN900

c. One to one connection from PC to IP camera

You can connect directly without switch. However, only the PC connecting to camera

can view the IP camera.





EAN900

3. Assign IPAddress

Please install IP utility software from CD before you go through the following

process. Please note the following procedures are an example according to EAN900

default values. These values may vary with your network system. Please consult your

ISP or network administrators for more detail of network setting reference.

IP utility (in supplied CD) is a recommended tool to assign IP address. The default

network setting is DHCP. Once login to EAN900, you can change TCP/IP setting for

your own environment.

1. Active IP Utility.

2. Click “Find Devices” button.

This helps to automatically obtain the EAN900 network configuration details including

Mac Address, Machine Name, Machine Type, IP Type, Subnet Mask, Gateway Address,

DNS1Address, and DNS2Address.

EAN900

3. The IP address of EAN900 will be automatically detected and shown in the

window. Tick the selected EAN900.

4. If you want to manually change the IP setting, YOU MUST CLICK “LOGIN”. You

will be asked to enter “User ID” and “Password”. This is a security measure of

configuration setting, in order to modify those network configurations of EAN900.

EAN900 administrator can only do the setting. Therefore only who has admin

authority could modify these settings. The ID & password must be the admin user and

be sent to the device when you click "Set configuration". If the ID and password do

not belong to an admin user, then setting will be discarded.

NOTE: Default User ID is “user1” and default password is “11111111”.

Otros manuales para NeVio EAN900

Tabla de contenidos

Otros manuales de Cámara de seguridad de EverFocus

EverFocus

EverFocus EZ760 Manual del propietario

EverFocus

EverFocus ED310e Manual de usuario

EverFocus

EverFocus ED300 Series Manual de usuario

EverFocus

EverFocus 288 Series Manual de usuario

EverFocus

EverFocus EPN4122 Manual de usuario

EverFocus

EverFocus EHD150 Manual de usuario

EverFocus

EverFocus ECD900F Manual de usuario

EverFocus

EverFocus EBD331e Manual de usuario

EverFocus

EverFocus Day / Night Speed Dome Camera EPTZ 100 Guía

EverFocus

EverFocus POLESTAR EHN7260 Manual de usuario

EverFocus

EverFocus EM-500NHP1 Manual de usuario

EverFocus

EverFocus Speed Dome EPTZ1000 Manual de usuario

EverFocus

EverFocus EPTZ3000 Manual de usuario

EverFocus

EverFocus EHD650 Manual de usuario

EverFocus

EverFocus Speed Dome EPTZ500 Manual de usuario

EverFocus

EverFocus EHH5241 Manual del propietario

EverFocus

EverFocus ED350 Manual de usuario

EverFocus

EverFocus EQ200E Manual de usuario

EverFocus

EverFocus M105-DE100-002 Manual de usuario

EverFocus

EverFocus EQH5200 Manual de usuario

EverFocus

EverFocus EMW990F Manual de usuario

EverFocus

EverFocus EZ610 Instrucciones de instalación

EverFocus

EverFocus EB200/E12 Manual de usuario

EverFocus

EverFocus Weatherproof Long Range IR Camera 235E Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario