ESAB Fabricator EM 401i Manual de usuario

Fabricator EM 401i,

Fabricator EM 501i

Instruction manual

0446 455 001  GB  20210630

Valid for: Serial number:

OP110YY-XXXXXX

TABLE OF CONTENTS

0446 455 001 -3- © ESAB AB 2021

1 SAFETY ...................................................................................................................................... 4

1.1 Meaning of symbols .................................................................................................... 4

1.2 Safety precautions ...................................................................................................... 4

2 INTRODUCTION ......................................................................................................................... 7

2.1 Equipment.................................................................................................................... 7

3 TECHNICAL DATA ..................................................................................................................... 8

4 INSTALLATION........................................................................................................................... 11

4.1 Location........................................................................................................................ 11

4.2 Lifting instructions ...................................................................................................... 11

4.3 Mains supply................................................................................................................ 12

5 OPERATION ............................................................................................................................... 14

5.1 Connections and control devices .............................................................................. 14

5.2 Welding control mode................................................................................................. 17

5.3 Connection of welding and return cable ................................................................... 19

5.4 Symbols and functions ............................................................................................... 20

5.5 Thermal protection ...................................................................................................... 20

5.6 Fan control ................................................................................................................... 20

5.7 Usage of the cooling unit............................................................................................ 21

5.8 Coolant connection .................................................................................................... 21

5.9 Coolant pressure controller ...................................................................................... 21

6 MAINTENANCE.......................................................................................................................... 22

6.1 Maintenance................................................................................................................. 22

6.2 Routine maintenance .................................................................................................. 22

6.3 Power source ............................................................................................................... 22

6.4 Cooling unit.................................................................................................................. 24

6.5 Filling the coolant........................................................................................................ 24

7 TROUBLESHOOTING ................................................................................................................ 25

8 ORDERING SPARE PARTS ....................................................................................................... 28

ORDERING NUMBERS ......................................................................................................................... 29

BLOCK DIAGRAM................................................................................................................................. 30

ACCESSORIES ..................................................................................................................................... 31

1  SAFETY

0446 455 001 -4- © ESAB AB 2021

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate, serious

personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual and follow

all labels, employer´s safety practices and Safety Data Sheets

(SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be observed

in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equipment.

Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the

operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

• its operation

• location of emergency stops

• its function

• relevant safety precautions

• welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

• no unauthorised person is stationed within the working area of the

equipment when it is started up

• no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

• be suitable for the purpose

• be free from drafts

4. Personal safety equipment:

• Always wear recommended personal safety equipment, such as safety

glasses, flame-proof clothing, safety gloves

• Do not wear loose-fitting items, such as scarves, bracelets, rings, etc.,

which could become trapped or cause burns

5. General precautions:

• Make sure the return cable is connected securely

• Work on high voltage equipment may only be carried out by a

qualified electrician

1  SAFETY

0446 455 001 -5- © ESAB AB 2021

• Appropriate fire extinguishing equipment must be clearly marked and

close at hand

• Lubrication and maintenance must not be carried out on the equipment

during operation

WARNING!

Wire feeders are intended to be used with power sources in MIG/MAG mode only.

If used in any other welding mode, such as MMA, the welding cable between wire feeder and

power source must be disconnected, or else the wire feeder becomes live or energized.

If equipped with ESAB cooler

Use ESAB approved coolant only. Non-approved coolant might damage the equipment and jeopardize

product safety. In case of such damage, all warranty undertakings from ESAB cease to apply.

Recommended ESAB coolant ordering number: 0465720002.

For ordering information, see the "ACCESSORIES" chapter in the instruction manual.

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions when

welding and cutting.

ELECTRIC SHOCK - Can kill

• Do not touch live electrical parts or electrodes with bare skin, wet gloves

or wet clothing

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side

of your body. Secure them with tape when possible. Do not

place your body between the torch and work cables. Never coil

the torch or work cable around your body. Keep welding power

source and cables as far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible

to the area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing

• Protect bystanders with suitable screens or curtains

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1  SAFETY

0446 455 001 -6- © ESAB AB 2021

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby

• Do not use on closed containers.

HOT SURFACE - Parts can burn

• Do not touch parts bare handed.

• Allow cooling period before working on equipment.

• To handle hot parts, use proper tools and/or insulated welding gloves to

prevent burns.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

CAUTION!

Class A equipment is not intended for use in residential locations

where the electrical power is provided by the public low-voltage

supply system. There may be potential difficulties in ensuring

electromagnetic compatibility of class A equipment in those

locations, due to conducted as well as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation in

accordance with national law, electrical and/or electronic equipment

that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment for

purchase. For ordering information contact your local ESAB dealer or visit us on our website.

2  INTRODUCTION

0446 455 001 -7- © ESAB AB 2021

2 INTRODUCTION

The Fabricator EM 401i and Fabricator EM 501i are welding power sources intended for MIG/MAG

welding, welding with powder filled cored wire (FCAW-S) and welding with coated electrodes (MMA).

The power sources are intended for use with the following wire feed units:

• Fabricator Feed 304

• Fabricator Feed 304w

EM 401i and EM 501i are available with a built-in cooling unit to support liquid cooled torches.

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of this manual.

2.1 Equipment

The power source is supplied with:

• 5m return cable with earth clamp

• Instruction manual

3  TECHNICAL DATA

0446 455 001 -8- © ESAB AB 2021

3 TECHNICAL DATA

FabricatorEM 401i / EM 401i with cooling unit

Mains voltage 380-415V ±10%, 50/60Hz

Mains supply Sscmin 1.9MVA

Primary current I max 380V 400V 415V

MIG/MAG 28 A 27A 25A

MMA 29 A 28A 26A

Setting range (DC)

MIG/MAG 30A/15.5V-400A/34.0V

MMA 30A/21.2 V-400A/36.0V

Permissible load at MIG/MAG

60% duty cycle 400 A/34.0 V

100% duty cycle 310 A/29.5 V

Permissible load at MMA

60% duty cycle 400 A/36.0 V

100% duty cycle 310 A/32.4 V

Power factor at maximum current 0.91

Maximum input power at idle mode <35 W

Efficiency at maximum current 86%

Open-circuit voltage 65.0V

Recommended wire 0.8 -1.2 mm

Operating temperature -10 to +40°C (14 to 104 °F)

Transportation temperature -40 to +70 °C (-40 to 158 °F)

Dimensions l × w × h 1035×500×1015mm (40.7×19.6×39.9in.)

Weight

Weight without cooling unit 102.0 kg (225 lbs)

Weight with cooling unit without coolant 107.5 kg (237 lbs)

Weight with cooling unit with coolant 111.5 kg (246 lbs)

Insulation class H

Enclosure class IP 23

Application class

FabricatorEM 501i with cooling unit

Mains voltage 380-415V ±10%, 50/60Hz

Mains supply Sscmin 6.2MVA

Primary current I max 380V 400V 415V

MIG/MAG 39 A 37A 36A

MMA 41 A 38A 37A

Setting range (DC)

3  TECHNICAL DATA

0446 455 001 -9- © ESAB AB 2021

FabricatorEM 501i with cooling unit

MIG/MAG 30A/15.5V-500A/39.0V

MMA 30A/21.2 V-500A/40.0V

Permissible load at MIG/MAG

60% duty cycle 500 A/39.0 V

100% duty cycle 390 A/33.5 V

Permissible load at MMA

60% duty cycle 500 A/40.0 V

100% duty cycle 390 A/35.6 V

Power factor at maximum current 0.91

Maximum input power at idle mode <35W

Efficiency at maximum current 87%

Open-circuit voltage 78.0V

Recommended wire 1.0-1.6 mm

Operating temperature -10 to +40°C (14 to 104 °F)

Transportation temperature -40 to +70 °C (-40 to 158 °F)

Dimensions l × w × h 1035×500×1015mm (40.7×19.6×39.9in.)

Weight

Weight with cooling unit without coolant 111.5 kg (246 lbs)

Weight with cooling unit with coolant 115.5 kg (255 lbs)

Insulation class H

Enclosure class IP 23

Application class

Cooling unit (500A - 60% duty cycle) Only for power sources with cooling units

Cooling power 1 kW at 25°C ambient temperature

Coolant ESABs ready mixed coolant

Coolant quantity 4.5 l

Maximum water flow 1.8 l/min

Maximum pressure lift for torch Qmax 66.7 PSI (4.6 bar)

Mains supply, Ssc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at a

certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration by solid

objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

3  TECHNICAL DATA

0446 455 001 - 10 - © ESAB AB 2021

Application class

The symbol indicates that the power source is designed for use in areas with increased electrical

hazard.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB Aristo Mig C3000i Manual de usuario

ESAB

ESAB ESP-50 Manual de usuario

ESAB

ESAB LHJ 750 Guía

ESAB

ESAB PowerCut 1600 Manual de usuario

ESAB

ESAB WeldCloud Mobile Manual de usuario

ESAB

ESAB MIGMASTER 250 Manual de usuario

ESAB

ESAB EM 215ic Manual de usuario

ESAB

ESAB Powercut 650 Manual de usuario

ESAB

ESAB LPH 120 Manual de usuario

ESAB

ESAB EAS IV Manual de usuario

ESAB

ESAB RS 400x Manual de usuario

ESAB

ESAB Caddy Mig C200i Manual de usuario

ESAB

ESAB ARC300i Manual de usuario

ESAB

ESAB PCM-1125 Manual de usuario

ESAB

ESAB Rogue ES 180i Manual de usuario

ESAB

ESAB ESABMig 325 Manual de usuario

ESAB

ESAB Origo Tig 3000i Manual de usuario

ESAB

ESAB EMP 205ic AC/DC Manual de usuario

ESAB

ESAB LUA 400 Manual de usuario

ESAB

ESAB Aristo Mig U5000i 400 V Manual de usuario

ESAB

ESAB Plasmarc EPP-450 Manual de usuario

ESAB

ESAB TAF 1251 Manual de usuario

ESAB

ESAB MEK 4 Manual de usuario

ESAB

ESAB ESABMig C420 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario