ESAB RS 400x Manual de usuario

RS 400x

Instruction manual

Welding Power Source

RS 400x

Instruction manual

For

Installation, Operation & General maintenance

SAFETY

Precautions for installation

Beware of electric shock!

Install grounding device according to application standard.

Do not touch live parts with naked skin, wet gloves or wet clothes.

Be sure you are insulated from ground and work piece.

Cover the cover plate of the machine before power on to avoid an

electric shock.

Confirm the safety of your working position.

Beware of fire hazard!

Please install the machine on non-combustible materials to avoid

a fire.

Make ensure there are no inflammables near the welding position

to avoid a fire.

Beware of explosion!

Do not install the machine in an environment with explosive gas

to avoid an explosion.

Replacing the components can be dangerous.

Only professionals can replace the components of the machine.

Make sure the connecting wires inside the machine are correctly connected after replacing the

PCBs, and then the machine can be run. Otherwise, there is a risk of damage to property.

Make sure there are no foreign bodies such as wire leads, screws, gaskets and metal bars

falling into the machine inside when replacing the components.

Carrying or moving the machine can be dangerous.

Cut the input power off via the switching box before moving the welding machine.

The handle can only be used for moving the welding machine by hand in short distance, and

it cannot be used for lifting. Otherwise, personal injury or property damage may be caused by

a drop.

Make sure that the flying rings are tightened, and that the machine enclosure and cover are

fixed when moving the welding machine with a crane,

Two lifting belts should be used when lifting the welding machine, and the angle formed by the

lifting belt and the vertical should be smaller than 15°.

Do not apply any stress on the operation panel and cover when moving the welding machine.

Otherwise, personal injury or property damage may be caused by a drop.

Do not install and run the welding machine when the machine is damaged or lacks any

components. Otherwise, fire hazard or personal injury may be caused.

Precautions for operation

Smoke-may be harmful to your health!

Keep your head away from the smoke to avoid inhalation of waste

gas in welding.

Keep the working environment well ventilated with exhaust or

ventilation equipment when welding.

Arc radiation-may hurt your eyes and burn your skin!

Use proper welding mask and wear protective clothing to protect

your eyes and body.

Use proper mask or curtain to protect onlooker from being injured.

Magnetic field can make cardiac pacemaker a bit wonky.

People with cardiac pacemaker should consult the doctor before

carrying out welding.

Stay away from the welding source to reduce the effect of magnetic

field.

Improper use and operation may result in a fire or an explosion.

Welding spark may result in a fire, so please make ensure there are

no inflammables near the welding position, and pay attention to fire

safety.

Ensure there is fire extinguisher nearby, and make sure someone

has been trained to operate the fire extinguisher.

Do not weld closed container.

Do not use this machine for pipe thawing.

Hot work piece can cause severe scald.

Do not touch hot work piece with bare hands.

Cool the welding torch for a while after continuously working.

Excessive noise does great harm to people’s hearing.

Wear ear covers or other hearing protectors when welding.

Give warning to onlooker that noise may be potentially hazardous to

hearing.

Moving parts may injure your body.

Please keep away from moving parts (like fan).

Each door, panel, cover, baffle plate, and protective device the like

should be closed and located correctly.

Seek professional support when trouble strikes.

When trouble strikes in installation and operation, please inspect

according to related contents in this manual.

If you still cannot understand fully, or you still cannot solve the

problem, please contact the service center to obtain professional

support.

TABLE OF CONTENTS

1. GENERAL DESCRIPTION..........................................................................7

Technical parameters ................................................................................

2. INSTALLATION AND CONNECTION ..........................................................8

Installation requirements............................................................................

Electrical connection..................................................................................

3. OPERATION...........................................................................................9-10

Panel functions of RS 400x ......................................................................

Rear Panel.................................................................................................

Output Terminals .......................................................................................

Work after welding.....................................................................................

4. MAINTENANCE ...................................................................................11-13

Daily maintenance.....................................................................................

Periodic check...........................................................................................

5. TROUBLESHOOTING...............................................................................14

6. WIRING DIAGRAM....................................................................................15

7. SPARES LISTAND EXPLODED DIAGRAM ........................................16-18

7 | P a g e

Specifications / Technical Data RS 400x

General Description

The RS 400X is thyristor based MMA welding machine. This unit uses 3~Phase

415V, 50 Hz AC power input supply. This machine is suitable for rutile and basic

electrodes. It can weld carbon steel, stainless steel.

It's main parts include: main transformer, three phase thyristor rectifier, control

PCB and inductance.

Description

Specification

Model

RS 400x

Input power V

415

Frequency Hz

Rated input current A

Rated input capacitance KVA

19.5

No-load voltage V

Rated working voltage V

MMA welding current A

50-400

Welding current（10min）A

60%@400

100% duty cycle A

310

Insulation class

Enclosure protection IP

21S

Cooling type

Fan cooled

Dimension L×W×H mm

705*420*790

Weight kg

130

8 | P a g e

INSTALLATION AND CONNECTION

Installation Requirements

1) Environment requirements

a) Do not install the machine at places with excessive dusts and metal powders.

b) Do not install the machine at places with corrosive or explosive gas.

c) The temperature of the working environment should be between -10℃and 40℃.

d) Do not carry out welding with the welding machine placed on a platform with a pitch

greater than 15°.

e) The machine should be installed in a well-ventilated place with humidity of 90% or less

and without water condense.

f) Pay attention to the wind at the welding site, and use wind deflector if necessary.

Otherwise, the welding process will be affected.

2) Installation space requirements

The welding machine should be at least 20cm away from the walls, and there should

be at least 30cm between them when two machines are installed side by side. Please refer

to the table below to determine the installation position of the welding machine.

Table 2-1: Reserved space when installing the welding machine

Machine part

Front

Top

Left

Right

Rear

Reserved space

≥20cm

≥10cm

≥20cm

Electrical connection

•High voltage danger from power source! Consult a qualified electrician for

proper installation of receptacle. This welder must be grounded while in use to

protect the operator from electrical shock.

• Do not remove grounding prong or alter the plug in any way. Do not use any

adapters between the welder’s power cord and the power source receptacle.

Make sure the POWER switch is OFF when connecting your welder’s power

cord to a properly grounded 3 phase 415 VAC, 50Hz, power supply.

9 | P a g e

OPERATION

Panel functions of RS 400x

1. Arc force adjusting knob

2. Digital display for output Amp

3. Output Current adjusting knob

4. Digital display for output Volt

5. Thermal protection indicator

6. Power input indicator

7. Output current range selecting switch

8. Main Power Switch

9. Remote control selecting switch

10. Remote control connector socket

10 | P a g e

Rear panel

Connect input cable with size >=10mm2.

Output Terminals

Work after welding

1) Cut off the power of the welding machine 3~5min after the welding work is

finished, so as to cool the internal part of the machine.

2) Turn off the air switch on the welding machine first and then switch off the

power in the switching box when shutting off the power.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB ESP-50 Manual de usuario

ESAB

ESAB R-50 Series Manual de usuario

ESAB

ESAB Heliarc 283i AC/DC Manual de usuario

ESAB

ESAB Caddy Tig 1500i VRD Manual de usuario

ESAB

ESAB Aristo WeldCloud Mig U5000i Manual de usuario

ESAB

ESAB MIGMATIC 250 Manual de usuario

ESAB

ESAB CoolMidi 1800 Manual de usuario

ESAB

ESAB Cutmaster 60 Manual de usuario

ESAB

ESAB LTH 161 Manual de usuario

ESAB

ESAB Caddy Mig C160i Manual de usuario

ESAB

ESAB ESABMig 325 Manual de usuario

ESAB

ESAB Buddy Arc 200 Manual de usuario

ESAB

ESAB Renegade ET 300i Manual de usuario

ESAB

ESAB Fabricator EM 400i Manual de usuario

ESAB

ESAB Caddy Arc 251i Manual de usuario

ESAB

ESAB PLASMAWELD 202 Manual de usuario

ESAB

ESAB POWERCUT-1250 Guía de configuración

ESAB

ESAB Warrior 750i CC/CV Manual de usuario

ESAB

ESAB Multimaster 260 Manual de usuario

ESAB

ESAB Origo Mig C420 PRO Manual de usuario

ESAB

ESAB Caddy Arc 251i Manual de usuario

ESAB

ESAB MultiPower 460 Pulse Manual de usuario

ESAB

ESAB ARC400i Manual de usuario

ESAB

ESAB Caddy 130 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario