ESAB Aristo Mig C3000i Manual de usuario

Aristo®, Origo™

Instruction manual

0459 825 301 GB 20180918 Valid for: serial no. 039-, 209-xxx-xxxx

Mig C3000i

TABLE OF CONTENTS

0459 825 301 © ESAB AB 2018

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 7

2.1 Equipment ............................................................................................... 7

2.2 Control panel .......................................................................................... 7

3TECHNICAL DATA ...................................................................................... 8

4INSTALLATION............................................................................................ 10

4.1 Lifting instruction ................................................................................... 10

4.2 Location................................................................................................... 10

4.3 Mains power supply ............................................................................... 10

5OPERATION ................................................................................................ 12

5.1 Connections and control devices ......................................................... 14

5.2 Fan control .............................................................................................. 14

5.3 Overheating protection .......................................................................... 14

5.4 Welding without gas............................................................................... 15

5.5 Wire feed pressure ................................................................................. 15

5.6 Replacing and inserting wire................................................................. 16

5.7 Changing feed rollers............................................................................. 16

6MAINTENANCE........................................................................................... 17

6.1 Inspection and cleaning......................................................................... 17

7TROUBLESHOOTING ................................................................................. 18

8ORDERING SPARE PARTS ........................................................................ 19

DIAGRAM ............................................................................................................ 20

ORDERING NUMBERS....................................................................................... 22

WEAR PARTS...................................................................................................... 23

ACCESSORIES ................................................................................................... 25

Rights reserved to alter specifications without notice.

1 SAFETY

0459 825 301 -4- © ESAB AB 2018

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0459 825 301 -5- © ESAB AB 2018

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0459 825 301 -6- © ESAB AB 2018

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be

potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations,

due to conducted as well as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on

Waste Electrical and Electronic Equipment and its

implementation in accordance with national law,

electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling

facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0459 825 301 -7- © ESAB AB 2018

2 INTRODUCTION

Mig C3000i is a welding power source intended for MIG/MAG welding with solid wire made

of steel, stainless steel, aluminium as well as cored wire with or without shielding gas. It is

also possible to weld with coated electrodes (MMA welding).

The power sources comes in different variants, see chapter "ORDERING NUMBERS".

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

The welding power source is supplied with:

• Instruction manual for the welding power source

• Instruction manual in english for the control panel

• Decal with recommended wear parts

• 5 metre return cable

2.2 Control panel

The welding power source is supplied with one of the following control panels:

With knobs for setting the voltage and wire feed speed

/ current. Other settings by pushbuttons, with text

indication on the display panel.

A Mig C3000i power source equipped with a U6 control

panel also enables TIG welding.

MA24 With knobs for setting the voltage / QSet™ and wire

feed speed / current. Other settings by pushbuttons.

Detailed descriptions of the control panels can be found in separate Instruction manual.

Instruction manuals in other languages can be downloaded from the Internet: www.esab.com

3 TECHNICAL DATA

0459 825 301 -8- © ESAB AB 2018

3 TECHNICAL DATA

Mig C3000i

Mains voltage 400 V ±10 %, 3 ~ 50/60 Hz

Mains supply Ssc min 1.4 MVA

Primary current

Imax MIG/MAG 17 A

Imax MMA 18 A

Imax TIG 3) 14 A

No-load power demand when in the

energy-saving mode, 6.5 min. after welding

30 W

Setting range

MIG/MAG 16A/14.8V - 300A/29.0V

MMA 16A/20.6V - 300A/32.0V

TIG 3) 4A/10.2V - 300A/22.0V

Permissible load at MIG/MAG

35 % duty cycle 300 A / 29 V

60 % duty cycle 240 A / 26 V

100 % duty cycle 200 A / 24 V

Permissible load at MMA

30 % duty cycle 300 A / 32 V

60 % duty cycle 230 A / 29.2 V

100 % duty cycle 190 A / 27.6 V

Permissible load at TIG 3)

35 % duty cycle 300 A / 22 V

60 % duty cycle 240 A / 19.6 V

100 % duty cycle 200 A / 18 V

Power factor at maximum current

MIG/MAG 0.90

MMA 0.87

TIG 3) 0.89

Efficiency at maximum current

MIG/MAG 82.3 %

MMA 85.7 %

TIG 3) 75.9 %

Open-circuit voltage U0max

MIG/MAG without VRD function 1) 70 - 80 V

MMA without VRD function 1) 57 - 67 V

VRD function deactivated 2) 60 V

VRD function activated 2) < 35 V

3 TECHNICAL DATA

0459 825 301 -9- © ESAB AB 2018

Mig C3000i

Operating temperature -10 to +40°C

Constant A-weighed sound pressure < 70 db

Dimensions l × w × h 652 x 412 x 423 mm

Weight 43 kg

Insulation class transformer H

Enclosure class IP23

Application class

Torch connection EURO

Wire feed speed 0.8 - 25.0 m/min

Max. diameter wire bobbin 300 mm

Wire dimension

Fe

Ss

Al

Cored wire



0.6 - 1.2 mm

1.0 - 1.2 mm

0.8 - 1.2 mm

Shielding gas

max pressure

All types intended for MIG/MAG welding

5 bar

Motor current Imax 3.5 A

1) Valid for power sources without VRD specification on the rating plate.

2) Valid for power sources with VRD specification on the rating plate. The VRD function is

explained in the instructions for the control panel, if the panel has that function.

3) Valid for a power source controlled from a U6 control panel

Mains supply, Ssc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

0459 825 301 - 10 - © ESAB AB 2018

4 INSTALLATION

The installation must be carried out by a professional.

NOTE!

Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit power is

greater than or equal to Sscmin at the interface point between the user's supply and

the public system. It is the responsibility of the installer or user of the equipment to

ensure, by consultation with the distribution network operator if necessary, that the

equipment is connected only to a supply with a short-circuit power greater than or

equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.

4.1 Lifting instruction

4.2 Location

Position the welding power source such that its cooling air inlets and outlets are not

obstructed.

4.3 Mains power supply

 Check that the welding power source is connected to the correct

mains power supply voltage, and that it is protected by the correct

fuse size. A protective earth connection must be made in

accordance with regulations.

Rating plate with supply connection data



Otros manuales para Aristo Mig C3000i

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB EMP 205ic AC/DC Manual de usuario

ESAB

ESAB ESABMig C420 Manual de usuario

ESAB

ESAB ARC250i Manual de usuario

ESAB

ESAB Caddy Tig 1500i VRD Manual de usuario

ESAB

ESAB 100i Manual de usuario

ESAB

ESAB ST-21M Manual de usuario

ESAB

ESAB Caddyt Tig 150i Manual de usuario

ESAB

ESAB CIGWELD CutSkill 60 Manual de usuario

ESAB

ESAB Buddy Arc 200 Manual de usuario

ESAB

ESAB EPP-360 Manual de usuario

ESAB

ESAB Aristo 300 Manual de usuario

ESAB

ESAB Aristo Mig 5000iw WeldCloud Manual de usuario

ESAB

ESAB Origo Arc 458T Guía

ESAB

ESAB Origo Mig L305 Manual de usuario

ESAB

ESAB Aristo Tig 4000iw Manual de usuario

ESAB

ESAB LAW 420 Manual de usuario

ESAB

ESAB HandyPlasma 550 Guía de configuración

ESAB

ESAB Warrior 350i MV CC Manual de usuario

ESAB

ESAB PCM-1125 Manual de usuario

ESAB

ESAB Origo Tig 3001i Manual de usuario

ESAB

ESAB Origo Mig 4002cw Manual de usuario

ESAB

ESAB Warrior Feed 304 Manual de usuario

ESAB

ESAB MIG400iCCCV Manual de usuario

ESAB

ESAB Rustler EM 201C Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario