ESAB Aristo Mig U5000i 400 V Manual de usuario

Valid for serial no. 640--xxx--xxxx0459 291 201 GB 070920

Mig U5000i

Aristot

400 V version

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

4 TECHNICAL DATA 5.................................................

5 INSTALLATION 6....................................................

5.1 Lifting instructions 7.........................................................

5.2 Placing 7...................................................................

5.3 Mains power supply 7........................................................

5.4 Terminating resistor 8........................................................

5.5 Connection of multiple wire feed units 8........................................

6 OPERATION 10.......................................................

6.1 Connections and control devices 10............................................

6.2 Turning on the power source 11................................................

6.3 Fan control 11...............................................................

6.4 Overheating protection 11.....................................................

6.5 Cooling unit 11...............................................................

6.6 Remote control unit 12........................................................

7 MAINTENANCE 12....................................................

7.1 Daily 12.....................................................................

7.2 If necessary 12..............................................................

7.3 Every year 13................................................................

8 FAULT TRACING 14...................................................

9 ORDERING OF SPARE PARTS 14......................................

DIAGRAM 15............................................................

ORDERING NUMBER 18.................................................

SPARE PARTS LIST 19...................................................

ACCESSORIES 20.......................................................

-- 3 --

bu15d1ea

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source Mig U5000i, Mig U5000iw from serial number 620 (2006 w.20) are constructed and

tested in compliance with the standard EN 60974--1/--2 and EN 60974--10 in accordance with the re-

quirements of directive (2006/95/EC) and (2004/108/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Kent Eimbrodt

Global Director

Equipment and Automation

Laxå 2007--03--14

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

bu15d1ea

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

WARNING!

Read and understand the instruction manual before installing

or operating.

Do not use the power source for thawing frozen pipes.

WARNING!

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

-- 5 --

bu15d1ea

3 INTRODUCTION

The Mig U5000i is a MIG/MAG / TIG welding power source, which can also be used

for MMA welding.

There are two variants of the power source:

SMig U5000i without cooling unit

SMig U5000i with cooling unit.

NB: These instructions describe a Mig U5000i with a cooling unit.

The power source is intended for use with the Feed 3004 or Feed 4804 wire feed

units.

All the settings are made from the wire feed unit or control box U8.

ESAB’s accessories for the product can be found on page 20.

3.1 Equipment

The power source is supplied complete with terminating resistor, 5m return cable

and instruction manual.

4 TECHNICAL DATA

Mig U5000i

Mains voltage 400V, ±10%, 3∼50/60 Hz

Primary current

Imax MIG/MAG

Imax MMA

Imax TIG

39 A

40 A

31 A

No--load power demand when in the energy--saving mode,

6.5 min. after welding 50 W

Voltage/current range

MIG/MAG

MMA

TIG

8--60 V / 16--500 A

16-- 500 A

4 -- 500 A

Permissible load at MIG/MAG

60 % duty cycle

100% duty cycle

500 A / 39 V

400 A / 34 V

Permissible load at MMA

60 % duty cycle

100% duty cycle

500 A / 40 V

400 A / 36 V

Permissible load at TIG

60 % duty cycle

100% duty cycle

500 A / 30 V

400 A / 26 V

Power factor at maximum current 0.85

Efficiency at maximum current 86 %

Open--circuit voltage

MIG/MAG

MMA

TIG

72 -- 88 V

68 -- 80 V

72 -- 88 V

Operating temperature -- 1 0 t o + 4 0 ˚C

Transportation temperature -- 2 5 t o + 5 5 ˚C

-- 6 --

bu15d1ea

Mig U5000i

Dimensions, lxwxh

with cooling unit

625 x 394 x 496 mm

625 x 394 x 776 mm

Continual sound pressure at no--load <70db(A)

Weight

with cooling unit

69 kg

89 kg

Insulation class transformer H

Enclosure class IP 23

Application class

Cooling unit

Cooling power 2.0 kW at 40˚C temp. difference and flow1.0

l/min

Coolant 50 % water / 50% mono--ethylen glycol

Coolant quantity 5.5 l

Maximum water flow 2.0 l/min

Maximum number of water--cooled welding

guns/torches that may be connected

two MIG welding guns or

one TIG torch and one MIG welding gun

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio

interference. It is the user’s responsibility to take adequate precautions.

Note!

Connect the power source to the electricity mains with a network impedance of 0.190 ohm or lower. If the

network impedance is higher, there is a risk of flicker in the illuminators.

-- 7 --

bu15d1ea

5.1 Lifting instructions

Power source Trolley and power source Trolley2 and power source

5.2 Placing

Position the welding power source such that its cooling air inlets and outlets are not

obstructed.

5.3 Mains power supply

Check that the unit is connected to the correct mains power

supply voltage, and that it is protected by the correct fuse sizes.

A protective earth connection must be made, in accordance

with regulations.

Rating plate with supply connection data

Recommended fuse sizes and minimum cable areas

Mig U5000i 400 V 3μ50 Hz

Mains voltage 400 V

Mains cable area, mm24G6

Phase current, I RMS 31 A

Fuse

Anti--surge

Type C MCB

35 A

40 A

NB:

The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations.

They may not be applicable in other countries: make sure that the cable area and fuse sizes comply

with the relevant national regulations.

-- 8 --

bu15d1ea

5.4 Terminating resistor

In order to avoid communication interference, the ends

of the CAN bus must be fitted with terminating

resistors.

One end of the CAN bus is at the control panel, which

has an integral terminating resistor. The other end at

the power source must be fitted with the terminating

resistor, as shown on the right.

5.5 Connection of multiple wire feed units

With control unit U8 and wire feed units without control panel it is possible to manage

up to 4 wire feed units from one power source.

It is possible to choose between the following connections:

S1 TIG--torch and 1 MIG--gun (Universal power source required)

S2 MIG/MAG--guns

S1 TIG--torch and 3 MIG/--guns (Universal power source required)

S4 MIG/--guns

When welding with water--cooled MIG/--guns on all wire feed units, it is

recommended to connect a separate cooling unit for the 2 extra guns.

We recommend connecting the guns in parallel.

-- 9 --

bu15d1ea

Two wire feed units

A connection kit is required when connecting two wire feed units, see accessories on

page 20.

Four wire feed units

Two connection kits and an extra cooling unit are required when connecting four wire

feed units, see accessories on page 20.

-- 1 0 --

bu15d1ea

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

6.1 Connections and control devices

1Connection for cooling water from the TIG

torch -- RED

10 White indicating lamp -- Power supply ON

2Connection with ELP* for cooling water to

the TIG torch -- BLUE

11 Orange indicating lamp -- Overheating

3Cooling water filler 12 Connection for control cable to the wire

feed unit or to the terminating resistor

4Connection for welding current cable (+)

at MMA welding or for return cable at TIG

welding

13 Connection for gas hose

5Connection for remote control 14 Connection for welding current to the wire

feed unit

6Connection for return cable (--) or for wel-

ding current cable at TIG welding

15 Connection for cooling water to the wire

feed unit -- BLUE

7Connection for start signal from the torch. 16 Connection for cooling water from the wire

feed unit -- RED

8Connection for gas to the TIG torch

9Main power supply switch, 0 / 1 / START

* ELP = ESAB Logic Pump, see point 6.5

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB MEF 44N Manual de usuario

ESAB

ESAB LTG 410 Manual de usuario

ESAB

ESAB Aristo Arc 4000i Manual de usuario

ESAB

ESAB Origo A32 Manual de usuario

ESAB

ESAB Origo Feed 304N P4 Manual de usuario

ESAB

ESAB MIG400iCCCV Manual de usuario

ESAB

ESAB MIG-41 Manual de usuario

ESAB

ESAB EPP-200 Manual de usuario

ESAB

ESAB ESABMig 325 Manual de usuario

ESAB

ESAB Aristo YardFeed 2000 Manual de usuario

ESAB

ESAB OXWELD C-62 Manual de usuario

ESAB

ESAB LHF 250 Manual de usuario

ESAB

ESAB Rogue EM 180 Manual de usuario

ESAB

ESAB Origo Mig L305 Manual de usuario

ESAB

ESAB Powercut 650 Manual de usuario

ESAB

ESAB CIGWELD WeldSkill 185LCD Manual de usuario

ESAB

ESAB Powercut 650 Manual de usuario

ESAB

ESAB Cutmaster 120 Manual de usuario

ESAB

ESAB Origo Arc 256 Guía

ESAB

ESAB LKB 400W Manual de usuario

ESAB

ESAB Caddy Arc 151i Manual de usuario

ESAB

ESAB ES 150i PRO Manual de usuario

ESAB

ESAB ET 201i DC Manual de usuario

ESAB

ESAB Caddy 150 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario