ESAB WeldCloud Mobile Manual de usuario
Instruction manual
0464 547 001 GB 20171106 Valid for: Serial no: 648-xxx-xxxx
WeldCloud™ Mobile
TABLE OF CONTENTS
0464 547 001 © ESAB AB 2017
1SAFETY ....................................................................................................... 4
1.1 Meaning of symbols ............................................................................... 4
1.2 Safety precautions ................................................................................. 4
2INTRODUCTION.......................................................................................... 6
2.1 Equipment ............................................................................................... 6
3TECHNICAL DATA ...................................................................................... 7
4INSTALLATION............................................................................................ 8
5OPERATION ................................................................................................ 10
5.1 Connections and control devices ......................................................... 10
5.2 Startup sequence ................................................................................... 11
6MAINTENANCE........................................................................................... 12
6.1 Inspection and cleaning......................................................................... 12
7ORDERING SPARE PARTS ........................................................................ 13
DIAGRAM ............................................................................................................. 14
ORDERING NUMBERS........................................................................................ 15
ACCESSORIES .................................................................................................... 16
Rights reserved to alter specifications without notice.
1 SAFETY
0464 547 001 -4- © ESAB AB 2017
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2 Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
1 SAFETY
0464 547 001 -5- © ESAB AB 2017
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment and its implementation
in accordance with national law, electrical and/or electronic
equipment that has reached the end of its life must be
disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
2 INTRODUCTION
0464 547 001 -6- © ESAB AB 2017
2 INTRODUCTION
WeldCloud™ Mobile enables two-way communication between the welding power source
and a remote WeldCloud™ server, either through Wi-Fi, Wired LAN or 3G. The
WeldCloud™ Mobile incorporates a GPS functionality to track the location of the welding
power source. There is also a Bluetooth interface to enable connection to a Bluetooth
device, for example a Bluetooth enabled bar code scanner.
WeldCloud™ Mobile can be used with power sources that are fitted with a W82control unit
or a PEK control panel.
2.1 Equipment
WeldCloud™ Mobile is supplied with:
• An instruction manual
• A control cable for connection to a W82control unit or to a PEK control panel
• Two Ethernet cables for connection to LAN and W82control unit or PEK control panel
Instruction manuals in other languages can be downloaded from the Internet:
www.esab.com
3 TECHNICAL DATA
0464 547 001 -7- © ESAB AB 2017
3 TECHNICAL DATA
WeldCloud™ Mobile
Supply voltage from power source through W8232-50 V AC, 50-60 Hz
Weight 2.15 kg (4.74lb)
Dimensions (l × w × h) 205 × 135 × 189 mm
(8.07×5.31×7.44in.)
Enclosure class IP23
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
4 INSTALLATION
0464 547 001 -8- © ESAB AB 2017
4 INSTALLATION
WeldCloud™ Mobile can be used with all power sources that are fitted with a W82control
unit or PEK control panel.
Install the WeldCloud™ Mobile on the W82
1. Clean the top of the W82control unit
using alcohol before assembling the
WeldCloud™ Mobile on top of it.
2. Remove the protection cover on the Dual
Lock fastener.
3. Attach the WeldCloud™ Mobile centered
on the W82control unit as indicated by
the grey area in the illustration.
Connect the WeldCloud™ Mobile
1. Make sure that all the involved equipment
is powered down.
2. Connect the control cable from the
Internal CAN on the W82control unit to
the CAN connector on the WeldCloud™
Mobile.
3. Connect the Ethernet cable from the W82
control unit to LAN port 1 on the
WeldCloud™ Mobile.
4. Optional, if not using Wi-Fi or 3G:
Connect an Ethernet cable from the LAN
connector 2 on the WeldCloud™ Mobile
to external LAN. Make sure not to clamp
the Ethernet cable with power cables or
welding cables.
For connections on WeldCloud™ Mobile,
see section OPERATION.
CAUTION!
When using WeldCloud™ Mobile on a tractor, do not use wired LAN for data
transfer. Risk for personal injury or damaged equipment.
Make sure the antenna on the WeldCloud™ Mobile is not covered or blocked.
NOTE!
The Dual Lock adhesive bonds with the surface of the W82control unit for 24
hours to gain full strength.
4 INSTALLATION
0464 547 001 -9- © ESAB AB 2017
Remove and attach the WeldCloud™ Mobile on the W82
To remove: Grab the bottom of the WeldCloud™ Mobile and pull it slowly outwards from the
W82control unit, as shown to the left in the illustration below.
To attach: Put the WeldCloud™ Mobile straight down on the W82control unit, as shown to
the right in the illustration below. Make sure that the Dual Lock fastener stems are
completely fitted.
Install WeldCloud™ Mobile with PEK
Contact your service center for guidance for the specific system configuration.
5 OPERATION
0464 547 001 - 10 - © ESAB AB 2017
5 OPERATION
5.1 Connections and control devices
1. Antenna
Combined Wi-Fi, 3G and GPS antenna to provide wireless connectivity
2. Status indicating LED
Indicates the status of WeldCloud™ Mobile
3. Power on LED
Indicates that there is power to the WeldCloud™ Mobile
4. LAN connector 2
Ethernet port 2 used for external connections
5. CAN connector, male
Used to provide power supply to WeldCloud™ Mobile and to connect the control
cable to the W82control unit or to the PEK control panel
6. CAN connector, female
Used for communication with ESAB wire feed unit
7. LAN connector 1
Ethernet port 1 used to connect to W82control unit or to PEK control panel
Otros manuales para WeldCloud Mobile
1
Tabla de contenidos
Otros manuales de Sistema de soldadura de ESAB
ESAB
ESAB Warrior Feed 304 Manual de usuario
ESAB
ESAB AristoFeed 30 Manual de usuario
ESAB
ESAB AristoPower 4600c Manual de usuario
ESAB
ESAB THERMAL DINAMICS CUTMASTER 60i Manual de usuario
ESAB
ESAB A6 Mastertrac Manual de usuario
ESAB
ESAB Origo Arc 810c Manual de usuario
ESAB
ESAB A22 POB Instrucciones de uso
ESAB
ESAB Pipeweld Orbiter Manual de usuario
ESAB
ESAB Aristo 500ix Manual de usuario
ESAB
ESAB RobustFeed AVS Manual de usuario
ESAB
ESAB RS 400x Manual de usuario
ESAB
ESAB Aristo Mig 5000i Manual de usuario
ESAB
ESAB LAW 510 Manual de usuario
ESAB
ESAB Origo Mig C170 3ph Manual de usuario
ESAB
ESAB Origo Mig 4004i A44 Manual de usuario
ESAB
ESAB CIGWELD WeldSkill 185LCD Manual de usuario
ESAB
ESAB LPH 80 Manual de usuario
ESAB
ESAB A6 DK Manual de usuario
ESAB
ESAB Caddy Series Manual de usuario
ESAB
ESAB 100i Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
Elettro
Elettro HI-MIG 3000 SYNERGIC Manual de usuario
