ERNITEC ECB Series Manual de usuario

Day&Night Hi-Res Colour CCD

Camera

ZEIM-0050696G A.3

CAUTIONS -----------------------------------------------------------------------------

SYSTEM COMPONENTS ---------------------------------------------------------

PIN CONNECTIONS -----------------------------------------------------------------

PARTS NAMES & FUNCTIONS --------------------------------------------------

PUSH BUTTONS AND THEIR FUNCTIONS ----------------------------------

SETTING MENU ----------------------------------------------------------------------

SUB MENU -----------------------------------------------------------------------------

OSD FUNCTION DESCRIPTION ------------------------------------------------

SYSTEM EXTENSIONS -------------------------------------------------------------

SPECIFICATIONS ---------------------------------------------------------------------

IMPORTANT SAFETY INSTRUCTIONS

1. CAUTIONS

Do not touch the imaging surface of

sensor. Use soft cloth moistened with

alcohol to clean the surface if it is

touched accidentally.

Ensure the supply voltage is correct

as speciﬁed for the particular variant of

camera before operation.

Do not expose the camera to rain,

moisture or to temperature outside the

speciﬁed limit, without a suitable

housing.

Avoid focusing directly on the sun.

Do not attempt to service this unit

yourself unless you are authorised to

do so. Opening the camera may

expose you to dangerous voltages

or other hazards. Refer all servicing to

qualiﬁed personnel only.

3. SYSTEM CONNECTION

3.1 Basic System Connection

If connected to the mains :

THIS APPARATUS MUST BE EARTHED.

The wires on the mains lead are in

accordance with the following code :

GREEN/YELLOW ------------------Earth

BLUE ----------------------------------Neutral

BROWN ------------------------------Live

Warranty void if the S/N label on

camera is removed.

2. SYSTEM COMPONENTS

Camera -----------------------------------1

Instruction Manual ---------------------1

Lens Mounting Cap --------------------1

Hexagonal Wrench ---------------------1

AI Lens 4-pin Plug ----------------------1

NOTES OF USE

3.2 Extended System Connection

4 PIN CONNECTIONS

5. PARTS NAMES & FUNCTIONS

Lens Mount (CS Mount) :

For installation of CS Mount lenses

only.

Tripod Stand :

Application for camera mounting onto

the camera holder. Effective for general

camera tripods.

Exposure Control :

a. Auto IRIS mode (two types of lens

are appropriate for this function):

DC IRIS lens :

Set the IRIS slide switch to the DC

position and adjust the LEVEL

control on the side panel to obtain a

clear picture.

Video IRIS lens : Set the IRIS slide s

witch to the VIDEO position and

adjust the LEVEL and ALC controls

on the lens to obtain a clear picture.

b. Automatic Electronic Shutter ( AES ):

Set the IRIS slide switch to the AES

position to automatically adjust the

shutter speed according to the

subjects brightness.

V-PHASE Adjustment

When using two cameras or more, the

image on the monitor may roll vertically

when switching sources. This rolling

can be minimized by adjusting this

controller.

Function RJ-45

DATA + (RS-485)

GND

POWER(+5V) 2

DATA - (RS-485)

PREDTMSP

B/W

GND

C/L

45 78

NOTES OF USE

DC IRIS LEVEL Adjustment

If using a DC type auto-iris lens, you

will need to set the LEVEL volume.

Turn counterclockwise (L) for a darker

picture. Turn clockwise (H) for a

brighter picture.

Back-Focus Adjustment :

a. Back Focus Screw :

Loosen this screw before using the

Focus Adjustment and to maintain

correct focus afterwards ensure it is

tightened.

b. Focus Adjustment :

Adjust this dial to obtain correct

back-focus whilst using a CS mount

lens.

Menu / Set-up Buttons :

For menu access and adjustment.

Video Output Terminal (BNC) :

Used to give out the video signal.

Connected to the video input terminal

of a monitor, switcher, etc. (to be

terminated with 75 ohm impedance).

6. PUSH BUTTONS AND THEIR FUNCTIONS

Switch Name

Function / Adjustment select (UP)

Main Function

Menu access, function select

Function / Adjustment select (DOWN)

Continue to press more than 2 seconds

to access SUB MENU

Select

All dimensions by mm

Bottom Rear

Front

Side

Top

260V

AC90~

Rear

AC24V

DC12V/

SETUP PROCEDURES

7. SETTING MENU

GAIN

SYNC

GAMMA

BLC

WHITE BAL

APERTURE

PREDTMSP

STD

SHUTTER AUTO 1/50(PAL);1/60(NTSC)

1/2501/5001/10K 1/4K 1/2K 1/1K

D/N MODE AUTO B.C.GMANUAL

D/N LEVEL HIGH LOW

D/N FIL ON OFF

WIDE

INT LL

0.45 1

OFF BLC1 BLC2 BLC3 BLC4

ATW1 ATW2 AWC R:0~6 B:0~63

HIGH LOW MID

ID.

ID POS

NEXT/BACK

OFF TOP BOTTO

EXIT CANCEL DEFAULT

Default Setting

1/120(PAL);1/100(NTSC)

OFF 1/50(PAL);1/60(NTSC)

1/2501/500

1/10K 1/4K 1/2K 1/1K

1/120(PAL);1/100(NTSC)

WITH IR LAMP NO YES

SETUP PROCEDURES

8. SUB MENU

Press and hold the ↑button on the side of the camera body for about 2 seconds until the

menu appears on the monitor. The blinking area represents the option to be set.

Note :

All of functions in SUB MENU are used for connection with remote control box (Optional)

or PC Software.

SUB

001 199

Default Setting

ADDRESS

PELCO P PELCO D

PROTOCOL

1200

BIT RATE 2400 4800 9600

SOFT VER

EXIT DEFAULT

ERNITEC

LANGUAGE ENGLISH FRANCAIS GERMAN

9. OSD FUNCTION DESCRIPTION

SETTING MENU

D/N MODE :

AUTO : When set to this mode, the

camera will change to COLOUR mode

and B/W mode automatically according

to a subject's brightness.

MANUAL : When set to this mode, the

camera will remain in COLOUR or B/W

mode by MANUAL selection.

B.C.G : When set to this mode, the

camera will change to COLOUR mode

and B/W mode manually according to

a RJ-45 B,C,G commands.

D/N LEVEL :

Set up a switch-over point from B/W

mode to COLOUR mode. Use the

SELECT button to select HIGH or LOW

Under the AUTO mode, the switchover

point of brightness from COLOUR

mode to B/W is 1.5 lux.

LOW : The switchover point of

brightness from B/W to COLOUR mode

is 4.5 lux.

HIGH : The switchover point of

brightness from B/W to COLOUR

mode is 7.5 lux.

( To switch between Colour mode and

B/W mode withina short time, use this

setup.)

SETUP PROCEDURES

D/N FIL :

ON : Y-signal ﬁlter of CCD output is

narrow in B/W mode. In this position,

the horizontal resoulation is 480TV

lines.

OFF : Y-signal ﬁlter of CCD output is

wide in B/W mode. In this position, the

horizontal resoulation is 600TV lines.

(If there is horizontal noise in B/W

mode,set to ON)

SHUTTER :

Selection of shutter speed from AUTO

to 1/10K. Sequentially contains AUTO,

1/50(PAL) or 1/60(NTSC), 1/120(PAL)

or 1/100(NTSC) , 1/250, 1/500, 1/1K,

1/2K, 1/4K, 1/10K.

When the slide switch is set to :

AES Mode : Shutter will be able to

select from AUTO to 1/10K.

DC/VIDEO Mode : Shutter will be able

to select from 1/50(PAL) or 1/60(NTSC)

to 1/10K.

GAIN :

STD :Standard position, GAIN=22dB.

WIDE :High-sensitivity position,

GAIN=30dB.

SYNC :

INT : The camera is in the internal

SYNC mode.

LL : The camera is in the LineLock

Mode.Adjusting degrees by V-PHASE

control on the side panel.

GAMMA :

Selection of GAMMA curvature for

GAMMA correction. 0.45 and 1 are

able to select.

BLC :

Selection of backlight compensation

mode.

OFF : The BLC function is off.

Backlight compensation window is like

BLC1 BLC2

(Bottom-Centre Window) (Centre Window)

BLC3

(Bottom Window) (Top Window)

BLC4

WHITE BAL :

ATW1(INDOOR) :

TTL auto trace white balance algorithm

is designed to implement a perfect

colour reproduction. Colour temperature

range is 2600oK~6000oK.

ATW2(OUTDOOR) :

TTL auto trace white balance algorithm

is designed to implement a perfect

colour reproduction. Colour temperature

range is 2500oK~9500oK.

The white balance is automatically

adjusted, within 3 seconds, to

the correct colour temperature of the

environment.

MANUAL :

Manually adjust the R and B (red&blue)

values.

APERTURE :

Selection of picture sharpness (HIGH,

LOW, MID).

PREDTMSP :

(Pre-determined shutter speed)

Preset of shutter speed. When external

controler active this functon, shutter

speed will be change to preset value.

(Manually according to a RJ-45

PREDTMSP command.)

10)

11)

ID. :

16 characters Max. (alpha-numeric).

Using to name each camera.

ID POS :

OFF : No ID display.

TOP : Display the ID in the top left of

screen.

WITH IR LAMP

Use enter to get into the submenu.

Using LEFT/RIGHT button, to choose

YES or NO.

*When the environment with extra IR

lights, the ICR ﬁlter may hunt

continually. If it occurs, turning this

function YES is able to ﬁx this issue.

**The default setting is NO.

NEXT BACK :

Selection of next page and last page.

EXIT :

Save all settings and exit.

12)

13)

14)

15)

16)

SETUP PROCEDURES

CANCEL :

Reset back to original settings.

DEFAULT :

Recall factory settings.

10. SYSTEM EXTENSIONS

10.1 Connection with Remote Control

Box (Optional)

To connect this camera with Remote

Control Box to obtain more function.

(B.C.G Control, PREDTMSP, 4 Alarm-

In, 2 Alarm-Out …etc.)

10.1-1 Camera & Control Box RJ-45 Pin

deﬁne :

17)

18)

Function RJ-45

DATA + (RS-485)

GND

POWER(+5V) 2

DATA - (RS-485)

PREDTMSP

B/W

GND

C/L

45 78

10.1-2 Single Camera Installation :

COA X

CAT 5

RS-232

C/DC POWER

ADAPTOR

SETUP PROCEDURES

10.1-3 Multi-Camera Installation :

SYSTEM

MA TRIX

RS- 485

RS- 232

CA M001

CA M199

CA M002

C/DC POWER

ADAPTOR

10.2 Connection with Switcher Box (Optional)

To connect this camera with Switcher Box to obtain simple control function.

(B.C.G Control and PREDTMSP)

Rear

OFF

B/W

AUTO

C/L

MODE PREDTMSP

SETUP PROCEDURES

10.3 B.C.G & PREDTMSP Control

Function RJ-45

DATA + (RS-485)

GND

POWER(+5V)

DATA - (RS-485)

PREDTMSP

B/W

GND

C/L

45 78

B.C.G function :

When D/N MODE set to B.C.G mode, the

camera will change to COLOUR MODE and

B/W MODE manually according to a RJ-45

B.C.G commands.

Control Terminal Image

B = Pin 6 C = Pin 4 G = Pin 5

(

OFF

)

(

OFF

)

GND Auto

(

)

(

)

GND

(

OFF

)

(

)

GND Colour

(

)

(

OFF

)

GND Black and White

PDSP(PREDTMSP, Pre-determined Shutter

Speed) function :

According to a RJ-45 PDSP commands,

the shutter speed will manually change to

Pre-determined shutter speed which is set

in OSD menu.

Control Terminal PREDTMSP

Pin 3 Pin 7

(

OFF

)

GND OFF

(

)

GND ON

Note :SW1&SW2 symbolise electronic switching (PIR) or manual

switching (Voltage free contact).

10.4 Conection with PC (Optional)

RS-232

Converter

RS-485

To connect this camera with PC and control

it by PC software RS-232. This converter

is not a standard or optional accessory, but

it's easy to obtain in the market conditions.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de ERNITEC

ERNITEC

ERNITEC MERCURY SX 5TH GENERATION Manual de usuario

ERNITEC

ERNITEC Orion DX 832 IR Manual de usuario

ERNITEC

ERNITEC Hawk SX Manual de usuario

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manual de usuario

ERNITEC

ERNITEC SX Series Manual de usuario

ERNITEC

ERNITEC Orion/2 Manual de usuario

ERNITEC

ERNITEC Orion/2 Manual de usuario

ERNITEC

ERNITEC Performance Series Manual de usuario

ERNITEC

ERNITEC DS-2XM6726G0-IS/ND Manual de usuario

ERNITEC

ERNITEC MicroView MVID-03IR-E Manual de usuario

ERNITEC

ERNITEC DS-2CD6924G0-IHS Manual de usuario

ERNITEC

ERNITEC MicroView MVIC-04IR-E Manual de usuario

ERNITEC

ERNITEC Mercury SX4 series Manual de usuario

ERNITEC

ERNITEC MicroView MVIC-O4IR-E Manual de usuario

ERNITEC

ERNITEC Orion SX Series Manual de usuario

ERNITEC

ERNITEC Orion Manual de usuario

ERNITEC

ERNITEC Orion DX 3 Manual de usuario

ERNITEC

ERNITEC SX Manual de usuario

ERNITEC

ERNITEC Mercury SX32 Series Manual de usuario

ERNITEC

ERNITEC MVID-04IR-E Manual de usuario

ERNITEC

ERNITEC MicroView MVIB-01IR-E Manual de usuario

ERNITEC

ERNITEC MicroView MVIB-01IR-E Manual de usuario

ERNITEC

ERNITEC EVA 101 Manual de usuario

ERNITEC

ERNITEC Orion DX 822IR Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario