Epson M-G3 Series Manual de usuario

Rev.20181129

IMU (Inertial Measurement Unit)

IMU / USB Interface Board

(M-G3xx, M-V3xx)

Logger Software

User’s Guide

Evaluation board/kit and Development tool important notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,

or development purposes only. Do not use it for other purpose. It is not intended to meet the requirement of

design for finished product.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is not the

product for consumer. The user should use this goods properly and safely. Seiko Epson dose not assume any

responsibility and liability of any kind of damage and/or fire coursed by usage of it. User should cease to use

it when any abnormal issue occurs even during proper and safe use.

3. The part used for this evaluation board/kit or development tool is changed without any notice.

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written

permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.

Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material

or due to its application or use in any product or circuit and, further, there is no representation that this material is

applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any

intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that

anything made in accordance with this material will be free from any patent or copyright infringement of a third

party. This material or portions thereof may contain technology or the subject relating to strategic products

under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license

from the Ministry of Economy, Trade and Industry or other approval from another government agency.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective

companies.

 
IMU/USB Interface Board  SEIKO EPSON CORPORATION i
Logger Software User’s Guide (Rev.20181129) 
 
 
Table of Contents 
 
Overview ..................................................................................................................... 1
Preparation ................................................................................................................. 2
1 Requirement................................................................................................................................2
1.1 System Requirement .............................................................................................................2
1.2 Other Required Software.......................................................................................................2
2 Preparing to Use the Software..................................................................................................2
3 Installing / Uninstalling the Software .......................................................................................2
Using the Software....................................................................................................... 3
1 Starting the Software .................................................................................................................3
2 Setting..........................................................................................................................................4
2.1 Serial Port Settings................................................................................................................4
2.2 IMU Settings ..........................................................................................................................5
2.3 Log Settings...........................................................................................................................7
3 Starting / Stopping Sampling....................................................................................................8
4 Self Test .....................................................................................................................................10 
5 Exiting the Software.................................................................................................................10 
6 Display and Output Data of Attitude Angle ...........................................................................11 
7 Automatic Sampling Stop........................................................................................................12 
Log File ..................................................................................................................... 13 
1 Raw Data LOG...........................................................................................................................13 
2 Scale-Adjusted Data LOG........................................................................................................14 
3 Attitude Angle Sensor Data.....................................................................................................15 
4 Split Log File .............................................................................................................................15 
5 Note............................................................................................................................................16 
Revision History ............................................................................................................. 17 

1. Overview

IMU/USB Interface Board SEIKO EPSON CORPORATION 1

Logger Software User’s Guide (Rev.20181129)

1. Overview

The IMU logger software (“Software”) is an easy-to-use software tool running on the Windows PC designed to

collect data measured on the Inertial Measurement Unit (IMU) together with the USB Interface Board from Seiko

Epson. The Software is offered as a loan to the customers who want to use or evaluate the IMU from Seiko

EPSON.

The Software supports maximum of 6 IMUs of the same model type for the measurement.

Please do not launch multiple instances of the Software on the same PC.

For information about how to install the Software, see Chapter 2.

For information about how to use the Software, see Chapter 3.

IMU list for which this software can be used

V340PDD0

G320PDG0

G364PDC0

G364PDCA

G354PDH0

G365PDC0

G365PDF0

G370PDC0

G370PDF0

2. Preparation

IMU/USB Interface Board SEIKO EPSON CORPORATION 2

Logger Software User’s Guide (Rev.20181129)

2. Preparation

2.1 Requirement

2.1.1 System Requirement

This sub-section describes the system requirement of the Software.

•An IBM PC/AT compatible computer.

•The Software supports Windows 7 (32/64bit Edition) / Windows 10 (64bit Edition).

Other system environments are not tested by Seiko Epson.

• The required specifications for the IBM PC/AT compatible computer are as follows.

Supported OS

Windows 7 (64bit)

Windows 10 (64bit)

CPU

Recommended

2.0GHz Over

RAM

Recommended

2.0GB Over

2.1.2 Other Required Software

•The Software requires the Microsoft .Net Framework 4.5 runtime. Download and install the

Microsoft .Net Framework 4.5 runtime. Follow the Microsoft End-User License Agreement when

the .Net Framework 4.5 runtime is installed and used.

•When the USB Interface board is connected to the PC, the USB driver software from FTDI is required.

For information about the installation, see 2.2 Preparing to use the Software (2). Follow the terms of

use provided by FTDI, when using the USB driver from FTDI.

2.2 Preparing to Use the Software

(1) Fix the IMU on and connect the IMU to the USB Interface Board and then connect a USB cable

between the USB Interface Board and the PC.

(2) If the driver software (USB Serial Converter, USB Serial Port (COMx) is requested when the USB

Interface board is connected, install the driver using either of the following two methods.

•Update the driver via Windows Device Manager. (Automatic Update over the Internet is

recommended.)

•Access the FTDI website (http://www.ftdichip.com/Drivers/VCP.htm) and download the appropriate

driver for the OS you are using.

(3) If the display update of the Software is sluggish, go to Device Manager > USB Serial Port (COMx) >

Port Settings > Advanced, and change the setting of the Latency Time (msec) in BM Options from

“16” (default) to “1”. This may improve the situation.

2.3 Installing / Uninstalling the Software

Decompress the Software package under any folder and just double-click the executable file (Imulogger.exe) to

start the Software. To uninstall the Software, delete the whole decompressed folder. (Registry settings are not

used.)

3. Using the Software

IMU/USB Interface Board SEIKO EPSON CORPORATION 3

Logger Software User’s Guide (Rev.20181129)

3. Using the Software

This chapter describes basics of using the Software.

3.1 Starting the Software

Start the executable file of the Software (ImuLogger.exe).

* When this software is started for the first time or the IMU model is changed, restart the software after setting

“3.2.1 Serial port setting”.

・Example of Main Screen when the attitude angle output is not supported with IMU model.

・Example of Main Screen when the attitude angle output is supported with IMU model.

3. Using the Software

IMU/USB Interface Board SEIKO EPSON CORPORATION 4

Logger Software User’s Guide (Rev.20181129)

3.2 Setting

Start the executable file of the Software (ImuLogger.exe). Click the “Setup” tab in the upper part of the window

and click the “Config” button to open the setup window. The setup window has three tabs: one for Serial Port

settings, one for IMU settings, and one for Log settings. Click the “OK” to activate the settings and close the

window.

3.2.1 Serial Port Settings

(1) Configure the “Connect” to control the connection to each IMU. When the IMU is “checked”, the

connection is enabled.

(2) Configure the “Port”. Check the available port number for USB Serial Port (COMx) in the Device

Manager. Baud rate setting is fixed at 460800 baud.

(3) After changing the Serial Port settings, restart the Software. After restarting, the settings will

become effective.

3. Using the Software

IMU/USB Interface Board SEIKO EPSON CORPORATION 5

Logger Software User’s Guide (Rev.20181129)

3.2.2 IMU Settings

(1) In “Data Output Rate (Sps)”, specify the data output rate for the IMU. Select from the following

options. (Sps: Samples / sec)

- V340PDD： 15.625, 31.25, 62.5, 125, 250, 500, 1000 (Sps)

- Other Models：

15.625, 20, 25, 31.25, 40, 62.5, 80, 100, 125, 200, 250, 400, 500, 1000, 2000 (Sps)

(2) In “Filter TAP Number”, configure the built-in filter in the IMU. Select from the following options.

- No Filter/TAP1

- Moving Average Filter: 2, 4, 8, 16, 32, 64, 128

- Kaiser Filter (parameter=8)

Tap：32, 64, 128

Fc：50, 100, 200, 400Hz

* Although it is possible to specify “No Filter/TAP1”, this setting is not recommended.

* Please refer to the appropriate IMU data sheet for recomended Filter TAP Number of each Data Output

Rate(Sps)

* Kaiser filter is available only for G320PDG0, G364PDC0, G364PDCA, G354PDH0,

G365PDC0, G365PDF0, G370PDC0, G370PDF0.

(3) “Basic Orientation” is available only for G365PDC0, G365PDF0. When this is the case, please specify

the orientation of the IMU for X, Y and Z axis.

(4) In “Data Format”, specify the bit width of IMU output data.

- 16bit Data

- 32bit Data

* 32bit Data setting is only for G320PDG0, G364PDC0, G364PDCA, G354PDH0,

G365PDC0, G365PDF0, G370PDC0, G370PDF0.

* In case of 32bit Data setting, Maximum Data Output Rate (Sps) is 1,000 (Sps).

(5) In “Count Function”, select SamplingCount or ResetCount.

(6) The “Attitude Output” conditions are configured in “angle”.

- If “angle” is checked, it becomes enabled and active

- Select Output mode “Absolute Inclinometer Mode” or “Euler Angle Mode”

- Select “Data Format” to 16bit or 32bit for output

* Attitude Output is available only for G365PDC0, G365PDF0.

3. Using the Software

IMU/USB Interface Board SEIKO EPSON CORPORATION 6

Logger Software User’s Guide (Rev.20181129)

・Screen Image for V340PDD, G320PDG0, G364PDC0, G364PDCA, G354PDH0, G370PDC0, G370PDF0.

・Screen Image for G365PDC0, G365PDF0

3. Using the Software

IMU/USB Interface Board SEIKO EPSON CORPORATION 7

Logger Software User’s Guide (Rev.20181129)

3.2.3 Log Settings

(1) In “Folder”, specify the full path of the log folder. Click the “…” button to the right and select the log

folder in the file selection dialog box.

* Default Log folder in the software is “C:\imu_data\”

* Please select the user accessible folder for the log folder.

(2) In “Delimiter”, specify the delimiter character.

•Comma: Comma delimiter

•Tab: Tab delimiter

(3) In “Unit”, specify the data format used when the measurement data are saved.

•Digit: Raw data

•Scale: Scale-adjusted data (raw data multiplied by the scale factor)

The unit of output value can be selected from the following.

Gyro：the unit of output value “dps”or “rad/s”

Accl：the unit of output value “mG”or “m/s2”

Attitude：the unit of output value “deg”or “rad”* only for G365PDC0, G365PDF0.

(4) In “Comment”, specify the comment recorded in the beginning of the log file.

(5) In “CheckSum”, specify the logging of communication data error checking status.

(6) In “MaximumEntries”, specify the maximum sample entries per CSV “split” log file.

(7) In “MeasureControl”, specify the automatic sampling stop condition.

Set "Enable/disable automatic sampling stop" by "Termination condition" check.

The stop condition is set by time (Time) or sampling number (Count).

* The automatic sampling stop function is automatically disabled once it is executed.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Epson

Epson

Epson S 1C63 Series Manual de usuario

Epson

Epson S1C63454 Manual de usuario

Epson

Epson S1C62 Family Manual de usuario

Epson

Epson 0C88832 Manual de usuario

Epson

Epson S1D13505 Manual de usuario

Epson

Epson B80818 Series Manual de usuario

Epson

Epson UB-E04 Manual de usuario

Epson

Epson S1D15722 Series Manual de usuario

Epson

Epson S1C17704 Manual de usuario

Epson

Epson S1C63616 Manual de usuario

Epson

Epson S1V3G340 Manual de usuario

Epson

Epson S1C63666 Manual de usuario

Epson

Epson S5U1C63007P Manual de usuario

Epson

Epson C11CA31121 Manual de usuario

Epson

Epson OT-WL02 Manual de uso y cuidado

Epson

Epson S1C88655 Manual de usuario

Epson

Epson Discproducer PP-50BD Manual de usuario

Epson

Epson S1C33 Series Manual de usuario

Epson

Epson 6200A Manual de usuario

Epson

Epson S5U13U00P00C100 USB 2.0 Manual de usuario

Epson

Epson S1C88 Series Manual de usuario

Epson

Epson S5U13719P00C100 Manual de usuario

Epson

Epson S5U13C00M00C100 Manual de usuario

Epson

Epson XJack EFM288XJ Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario