Epson S5U1C63000P Manual de usuario

MF1408-01a

CMOS 4-BIT SINGLE CHIP MICROCOMPUTER

(S1C63 Family Peripheral Circuit Board)

S5U1C63000P

Manual

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko

Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any

liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or

circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such

as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there

is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright

infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic

products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from

the Ministry of International Trade and Industry or other approval from another government agency.

MS-DOS, Windows, Windows 95, Windows 98 and Windows NT are registered trademarks of Microsoft Corporation, U.S.A.

PC-DOS, PC/AT, PS/2, VGA, EGA and IBM are registered trademarks of International Business Machines Corporation, U.S.A.

NEC PC-9800 Series and NEC are registered trademarks of NEC Corporation.

All other product names mentioned herein are trademarks and/or registered trademarks of their respective owners.

New configuration of product number

Starting April 1, 2001, the configuration of product number descriptions will be changed as listed

below. To order from April 1, 2001 please use these product numbers. For further information, please

contact Epson sales representative.

Devices

S1 C63158 F0A01

Packing specification

Specification

Package (D: die form; F: QFP)

Model number

Model name (C: microcomputer, digital products)

Product classification (S1: semiconductor)

Development tools

S5U1 C63000 A1 1

Packing specification

Version (1: Version 1)

Tool type (A1: Assembler Package)

Corresponding model number

(63000: common to S1C63 Family)

Tool classification (C: microcomputer use)

Product classification

(S5U1: development tool for semiconductor products)

CONTENTS

S5U1C63000P MANUAL EPSON i

(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)

S5U1C63000P Manual (S1C63 Family Peripheral Circuit Board)

This manual describes how to use the S1C63 Family Peripheral Circuit Board (S5U1C63000P). This circuit

board is used to provide emulation functions when it is installed in the ICE (S5U1C63000H1/

S5U1C63000H2), a debugging tool for the 4-bit Single Chip Microcomputer S1C63 Family.

This manual describes only the common specifications of the S1C63 Family Peripheral Circuit Board

(S5U1C63000P), so refer to the S5U1C63000P Manual (Peripheral Circuit Board for S1C63xxx) for the model

dependent specifications. For details on ICE functions and how to operate the debugger, refer to the

separately prepared manuals.

Contents

CHAPTER 1INTRODUCTION____________________________________________ 1

1.1 Outline of S5U1C63000P .............................................................................1

1.2 Components of S5U1C63000P .....................................................................1

1.3 External View of S5U1C63000P................................................................... 1

CHAPTER 2SETTING UPTHE S5U1C63000P _____________________________ 2

2.1 Installing the S5U1C63000P in the ICE (S5U1C63000H1/S5U1C63000H2) ....... 2

2.2 Downloading Cricuit Data 1 – when new ICE (S5U1C63000H2) is used .............. 3

2.3 Downloading Cricuit Data 2 – when previous ICE (S5U1C63000H1) is used ....... 3

CHAPTER 3PRODUCT SPECIFICATIONS ___________________________________ 4

CHAPTER 1: INTRODUCTION

S5U1C63000P MANUAL EPSON 1

(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)

CHAPTER 1INTRODUCTION

1.1 Outline of S5U1C63000P

The S5U1C63000P provides on a board all the peripheral circuits of S1C63 Family microcomputers other

than the core CPU. By installing this board in the ICE (S5U1C63000H1/S5U1C63000H2) you can use it to

emulate each model in the S1C63 Family. This board contains a programmable gate array (FPGA) and

supports each model by downloading the circuit data from the host PC to the FPGAvia the ICE.

1.2 Components of S5U1C63000P

After unpacking your S5U1C63000P package, check to see that all of the following components are

included.

(1) S5U1C63000P main unit.............................................................................................. 1 board

(2) I/O cable (80-pin/40-pin ×2 flat type) .................................................................... 1 pair

(3) I/O cable (100-pin/50-pin ×2 flat type) .................................................................. 1 pair

(4) Connector for connecting to target system (40-pin)............................................... 2 pieces

(5) Connector for connecting to target system (50-pin)............................................... 2 pieces

(6) Warranty card ............................................................................................................... 1 card

(7) User registration card .................................................................................................. 1 card

(8) Precautions on Using the S5U1C63000P Peripheral Circuit Board ..................... 1 sheet

(9) S5U1C63000P Manual (S1C63 Family Peripheral Circuit Board) ........................ 1 copy

1.3 ExternalView of S5U1C63000P

VSVD

VC5

PRG

CLK

RESET

IOSEL2

XC4062XLA

VLCD

Fig. 1.3.1 External view of S5U1C63000P

CHAPTER 2: SETTING UP THE S5U1C63000P

2EPSON S5U1C63000P MANUAL

(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)

CHAPTER 2SETTING UPTHE S5U1C63000P

2.1 Installing the S5U1C63000P in the ICE (S5U1C63000H1/S5U1C63000H2)

(1) Unfasten the screws located on the left and right sides of the front panel of the ICE (S5U1C63000H1/

S5U1C63000H2) by turning them counterclockwise, then remove the front panel.

(2) Insert the S5U1C63000P board into the ICE along the its uppermost guide rails until the tip of the board

touches the back of the ICE. If some other board is mounted on the uppermost guide rails, remove that

board by using the jig supplied with the ICE before you insert the S5U1C63000P board (see Figure 2.1.3).

(3) Once the S5U1C63000P board has been inserted almost fully into the ICE, secure it in position by

using the jig supplied with the ICE (see Figure 2.1.2).

(4) When the above is done, replace the front panel.

(1), (4)

(2)

(3)

S5U1C63000P board

Fig. 2.1.1 Installing the S5U1C63000P board in the ICE (S5U1C63000H1/S5U1C63000H2)

•Installing the S5U1C63000P board

Set the jig included with the ICE into position as

shown in Figure 2.1.2. Using this jig as a lever,

push it toward the inside of the board evenly on

the left and right sides. After confirming that the

S5U1C63000P board has been firmly fitted into the

internal slot of the ICE, remove the jig.

•Dismounting the S5U1C63000P board

Set the jig included with the ICE into position as

shown in Figure 2.1.3. Using this jig as a lever,

push it toward the outside of the board evenly on

the left and right sides. After confirming that the

S5U1C63000P board has been dismounted from

the backboard connector, pull the S5U1C63000P

board out of the ICE.

S5U1C63000P board

Fig. 2.1.2

Installing the S5U1C63000P board

Fig. 2.1.3

Dismounting the S5U1C63000P board

CHAPTER 2: SETTING UP THE S5U1C63000P

S5U1C63000P MANUAL EPSON 3

(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)

2.2 Downloading Circuit Data 1 – when new ICE (S5U1C63000H2) is used

This board (S5U1C63000P) comes with the FPGAthat contains factory inspection data, therefore the

circuit data for the model to be used should be downloaded. The following explains the downloading

procedure.

1) Remove the ICE top cover and then set the DIP switch "IOSEL2" on this board to the "E" position.

2) Connect the ICE to the host PC. Then turn the host PC and ICE on.

3) Invoke the debugger included in the assembler package (ver. 5 or later). For how to use the ICE and

debugger, refer to the manuals supplied with the ICE and assembler package.

4) Download the circuit data file (.mot) corresponding to the model by entering the following commands

in the command window.

>XFER (erase all)

>XFWR <file name> (download the specified file)*

>XFCP <file name> (compare the specified file and downloaded data)

∗The downloading takes about 15 minutes.

5) Terminate the debugger and then turn the ICE off.

6) Set the DIP switch "IOSEL2" on this board to the "D" position.

7) Turn the ICE on and invoke the debugger again. Debugging can be started here.

2.3 Downloading Circuit Data 2 – when previous ICE (S5U1C63000H1) is used

The standard ICE (S5U1C63000H1, previous model) did not support the circuit data download function

for this board. To use the download function, update the ICE firmware according to the following

procedure.

1) Set the baud rate of the ICE to 9600 bps. Refer to the manual supplied with the ICE for setting the DIP

switch.

2) Connect the ICE to the host PC and then start up the host PC in DOS. When Windows is running,

restart in DOS mode.

Note: Do not use the DOS prompt of Windows.

3) Turn the ICE on.

4) Configure the RS232C parameters for the host PC as follows:

C:\>MODE COM1:9600,n,8,1,p (9600 bps, 8-bit data, 1 stop bit, no parity)

5) Copy the following files included in the assembler package (ver. 5 or later) to a directory on the hard disk.

tm63.exe, ice63.com, i63com.o, i63par

6) Move to the directory in Step 5, run the TM63. TM63 enters command ready status after invocation,

enter a command as follows:

________

C:\>tm63 xat

TM63 start on IBM PC

TM63 start V01.01

________________________________

>dlf ice63.com i63com.o i63par 0b

...

7) Enter "q" to terminate TM63 after the prompt mark is displayed.

8) The ICE firmware is now updated. Turn the ICE off and then download the circuit data by the proce-

dure described in Section 2.2.

CHAPTER 3: PRODUCT SPECIFICATIONS

4EPSON S5U1C63000P MANUAL

(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)

CHAPTER 3PRODUCT SPECIFICATIONS

The specifications of the S5U1C63000P are listed below.

S5U1C63000P

Dimension: 254 mm (wide) ×144.8 mm (depth) ×13 mm (height) (including screws)

Weight: Approx. 300 g

Power supply: DC 5 V ± 5%, less than 1 A (supplied from ICE main unit)

I/O connection cable (80-pin)

S5U1C63000P connector: KEL8830E-080-170L

Cable connector (80-pin): KEL8822E-080-171

Cable connector (40-pin): 3M7940-6500SC 1 pair

Cable: 40-pin flat cable 1 pair

Interface: CMOS interface (3.3 V)

Length: Approx. 40 cm

I/O connection cable (100-pin)

S5U1C63000P connector: KEL8830E-100-170L

Cable connector (100-pin): KEL8822E-100-171

Cable connector (50-pin): 3M7950-6500SC 1 pair

Cable: 50-pin flat cable 1 pair

Interface: CMOS interface (3.3 V)

Length: Approx. 40 cm

Accessories

40-pin connector for connecting to target system:

3M3432-6002LCSC ×2

50-pin connector for connecting to target system:

3M3433-6002LCSC ×2

Tabla de contenidos

Otros manuales de Hardware de computadora de Epson

Epson

Epson S5U1C62000A Manual de usuario

Epson

Epson DisplayPort ELPIF03 Manual de usuario

Epson

Epson S1C63616 Manual de usuario

Epson

Epson C11CA31121 Manual de usuario

Epson

Epson S1C88655 Manual de usuario

Epson

Epson S1C63666 Manual de usuario

Epson

Epson E0C6011 Manual de usuario

Epson

Epson DNUB-E1 Manual de usuario

Epson

Epson S5U13U00P00C100 USB 2.0 Manual de usuario

Epson

Epson Discproducer PP-50BD Manual de usuario

Epson

Epson UB-S01 Manual de usuario

Epson

Epson OT-WL02 Manual de uso y cuidado

Epson

Epson PP-100 III Manual de usuario

Epson

Epson E0C6001 Manual de usuario

Epson

Epson S5U1C62N51E1 Manual de usuario

Epson

Epson S5U1C17001C Manual de usuario

Epson

Epson E0C6006 Manual de usuario

Epson

Epson S1C60N03 Manual de usuario

Epson

Epson C32C824151 - UB E02 Print Server Manual de uso y cuidado

Epson

Epson S1C88 Series Manual de usuario

Epson

Epson UB-E04 Manual de usuario

Epson

Epson S1C63000 Manual de usuario

Epson

Epson S5U1C60N15E Manual de usuario

Epson

Epson S1C88650 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario