EPOX PP6-NF Manual de usuario

TRADEMARK

All products and company names are

trademarks or registered trademarks of

their respective holders.

The specification is subject to change without notice.

PP6-NF

ISA PCI

MotherBoard

with Onboard PCI IDE and Super Multi-I/O.

82440FX PCIset

-THIS PAGE INTENTIONALLY LEFT BLANK-

Contents

page

Chapter 1 - Introduction ................................................ 1-1

1-1 Pentium Pro Processor Overview .................................1-1

1-2 Specification.................................................................1-2

Chapter 2 - Hardware Design......................................... 2-1

2-1 Motherboard Layout .....................................................2-1

PP6-NF Board Layout...................................................2-2

System Block Diagram .................................................2-3

2-2 Connectors and Jumpers ...............................................2-4

2-3 System Memory Configuration .....................................2-7

2-4 Integrated PCI Bridge...................................................2-9

Chapter 3 - ATX Form-Factor Overview....................... 3-1

Chapter 4 - Award BIOS SETUP................................... 4-1

4-1 Standard CMOS Setup .................................................4-2

4-3 BIOS Features Setup ....................................................4-2

4-3 Chipset Features Setup .................................................4-6

4-4 Power Management Setup ............................................4-8

4-5 PNP/PCI Configuration ................................................4-10

4-6 Integated Peripherals....................................................4-12

4-7 Load Setup Defaults .....................................................4-14

4-8 Change Supervisor or User password............................4-15

4-9 IDE HDD Auto Detection.............................................4-16

4-10 HDD Low Level Format ...............................................4-18

4-11 Save & Exit Setup ........................................................4-18

4-11 Exit Without Saving .....................................................4-18

Chapter 5-Onboard Technical Information................... 5-1

5-1 I/O & Memory Map.....................................................5-1

5-2 Time & DMA Channels Map .......................................5-2

5-3 Interrupt Map...............................................................5-2

5-4 RTC & CMOS RAM Map ............................................5-3

Appendix A: Post Codes...................................................................5-4

Appendix B: I/O Connector .............................................................5-8

The "LOAD SETUP DEFAULTS"function loads the system default data directly

from ROM and initializes associated hardware properly. This function will be

necessary when you accept this motherboard, or the system CMOS data is corrupted.

LOAD SETUP DEFAULT

NOTE :

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

Load SETUP Default (Y/N)? Y

STANDARD CMOS SETUP SUPERVISOR PASSWORD

BIOS FEATURES SETUP USER PASSWORD

CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION

POWER MANAGEMENT SETUP HDD LOW LEVEL FORMAT

PNP/PCI CONFIGURA ETUP

INTEGRATED PERIPH SAVING

LOAD SETUP DEFAULTS

ESC: QUIT :SELECT ITEM

F10:Save & Exit Setup (Shift)F2 :Change Color

Load Setup Defaults Except Standard COMS SETUP

Introduction 1-1

Chapter 1

Introduction

The PP6-NF motherboard is a high performance system hardware

based on Intel Pentium Pro processor and is equipped with four PCI slots,

four standard ISA slots, Super Multi-I/O controller and dual ports PCI-

IDE connectors for the future expansion. The hardware dimension is Full

ATX form factor with four layer design technology.

1-1 Pentium Pro Processer Overview

The Intel Pentium Pro Processor is the 6th generation in the Intel

386TM, Intel 486TM, and Pentium family of processors. The Pentium Pro

Processor has several key features such as 12-stage superpipeline architec-

ture, Built-in 256KB/512KB cache, Out of order execution, dynamic

branch prediction & speculative execution and a pipestage time 33 percent

less than the Pentium Processor, which helps achieve a higer clock rate

on any given Process. It will be superpipelined for high clock speed from

150MHz up to 233MHz. The Pentium Pro Processor was used to the

Dynamic Execution that is the combination of improved branch predic-

tion, speculative execution and data flow analysis that enables the Pentium

Pro processor to deliver its superior performance from CPU architecture.

The Pentium Pro Processor is a 64 bit processor with RISC technology. It

requires 32-bit applications (like Microsoft Windows NT and OS/2) to

optimize its capabilities and performances. The Pentium Pro processor

delivers best value for businesses moving to 32-bit computing when useing

the 32-bit Operating System and Applications.

1-2 PP6-NF

1-2 Specification

Intel 82440FX PCIset chipset.

Intel Pentium Pro Processor operating at133 ~ 233 MHz with 387 ZIF

socket 8 is scalable to accept faster Processors in the future. The Pentium

Pro Processor is the next in the Intel386TM, Intel486TM, and Pentium family

of processor. The second Level Cache (L2), controller are some of the

components that existed in the Pentium Pro Processor.

Onboard VRM supports full line Pentium Pro CPU.(need No VRM in

Header 8)

Supports up to 768 MegaBytes DRAM(minimum of 8 MB) on board(72

Pin SIMM x 6, and BIOS auto FP DRAM, EDO and Burst EDO DRAM

detection and configuration.(Refer to Chapter 2-3 System Memory

Configuration)

Supports four 16 bits ISA slots, four 32 bits PCI slots, and provides two

independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3 and Mode 4 devices. The PP6-NF supports four PCI Bus

Masters and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI I/O controller card(s).

Supports ATAPI (e.g.CD-ROM) devices on both IDE interfaces.

Supports 1 floppy port, 1 parallel port (EPP,ECP port), and 2 serial ports

(16550 Fast UART compatible).

Supports aPS/2 style mouse and a PS/2 style AT keyboard connectors.

Supports Award Plug & Play BIOS . The BIOS is stored in Flash EPROM

form. It provides better upgradeability for the system.

Supports CPU Hardware sleep and SMM (System Management Mode).

PP6-NF utilizes Lithium battery which provides environmental protection

and longer life time.

Supports the USB connector for the future.

Supports ATX power Supply Connectors.

Supports PWR/ON Switch when ATX power Supply is plugged

Four Layer design technology and 245mm x 305mm full ATX form

factor.

Hardware Design 2-1

Chapter 2

Hardware design

2-1 Motherboard Layout

The PP6-NFis designed with Intel 82440FX PCIset chipset which is developed

by INTEL Corporation to fully support Pentium Pro Processor PCI/ISA system.

The Intel 82440FX PCIset chipset provides increased integration and improved

performance designs. The chipset provides an integrated IDE controller with two

high performance IDE interfaces for up to four IDE devices (hard devices, CD-

ROM device, etc). The SMC 37C669 Super I/O controller provides the standard PC

I/O function: floppy interface, two 16 Byte FIFO serial ports and EPP/ECP capable

parallel port. The PP6-NF layout is shown in nexts page ( Figure 1-1 ) for user's

reference. Care must be taken when inserting memory modules, inserting Pentium

Pro processor CPU or even plugging PCI card into associated slots to avoid

damaging any circuits or sockets on board. A right fan and heatsink fan is strongly

recommended when installing Pentium Pro processor due to possible overheat.

The PP6-NFsupports minimum of 8MB of System Memory and maximum of

768MB while L2 Cache and cache controller included in Pentium Pro Processor

CPU.

The PP6-NFsupports standard Fast Page, EDO (Extended Data Out or Hyper

Page Mode) or Burst EDO DRAM.The PP6-NFprovides six 72-pins SIMM

sites for memory expansion. The socket support 1M x 32(4MB), 2M x 32(8MB),

4M x 32(16MB), 8M x 32(32MB) 16MB x 32(64MB), and 32MB x 32(128MB)

single-sided or double-sided memory modules. The memory timing requires 70 nS

Fast page devices or 60 nS EDO DRAM. Memory parity generation and checking

or ECC(Error Checking and Correction) are supported(DRAM Modules may be

parity (x 72)or non-parity(x 64)or ECC(x 72). The BIOS will automaticlly detect

which DRAM has installed in SIMM sites.

The PP6-NF supports Onboard two PCI IDE connectors, and detects IDE

harddisk type by BIOS utility automatically.

The PP6-NF supports Award Plug & Play BIOS for the ISA and PCI cards. The

BIOS can be located in Flash EPROM. The advantage of having Flash EPROM is

much easier to replace BIOS code if necessary.

The PP6-NF's motherboard layout and system block diagram are shown in

Figure 1-1, 1-2.

2-2 PP6-NF

PCI#1

PCI#2

PCI#3

PCI#4

BANK0 BANK1

Intel

Socket 7

BIOS

RTC

RES

JP5

JP4

JP3

JP2

J817

SMC

37C669

JP15JP14

BANK2

ATX Power Conn.

JP13

JP10

JP6

J10

U18

U21

U31

U39

J17

J15 J16

Q4Q3

Figure 1-1

PP6-NF Layout

JP1

KEYLOCK

J5 J6J1

SPK.R TBLEDPWRON

PS/2

MOUSE

K/B

CONN.

PRINTER

CONN.

COM2

FDD CONN.

Primary IDE

Secendary IDE

USB CONN.

Socket 8

J7J4J2

SLEEPHD-LEDG-LED

82442FX

Intel

82441FX

Intel

Keyboard BIOS COM1

SIMM 6

SIMM 5

SIMM 4

SIMM 3

SIMM 2

SIMM 1

+ +J3 +

JP16

82371SB

Hardware Design 2-3

Processor

Family

DBX

Data Bus

Acceleraror

208PQFP

PIIX3

I/O Bridge

208 PQFP

PD[15:0]

CONTROL

IDE HDD

Graphics

Port_A

Port_B

><MD[63:0]>

<MPE[7:0]

PMC

PCI Bridge

and memory

controller

208 PQFP

BIOS

Flash EPROM KBC

8042

RTC

IDE CD-ROM

Universal Serial Bus

Figure 1-2 System Block Diagram

PCI Slots

ISA Slots

HOST BUS

PCI BUS

MAIN MEMORY

MA[11:0]

CONTROL

2-4 PP6-NF

1.Power LED(+)

2.N/C

3.GND

4.Keylock

5.GND

Speaker - connect to the system's speaker for beeping

1.Speaker

2.N/C

3.GND

4.GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

Sleep/Resume switch : Closed to enter sleep mode

A keystrobe or mouse movement (mouse driver exists). The

system will instantly "wake up".

Power Saving LED indicator - LED ON when system is in any

saving mode

IDE LED indicator - LED ON when Onboard PCI IDE

Harddisks activate

J1 KeyLock - Keyboard lock switch & Power LED connector

JP1 The system power ON/OFF switch for ATX power supply.

Use a mometary switch which is normally open. The system power

will be on when pushing the switch close and releasing immedi-

ately.

2-2ConnectorsandJumpers

This section describes all of the connectors and jumpers equipped in the motherboard.

Please refer to Figure 1-1 for actual location of each connector and jumper. The

following jumpers will be show graphically such as to connect pin 1&2 and to

connect pins 2&3. Jumpers with two pins will be shown as for open and for

close.

Tabla de contenidos

Otros manuales de Placa madre de EPOX

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario