EPOX MVP4G Manual de usuario

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 6.0

September 17, 1999

MVP4G

ISA/PCI Motherboard with Onboard AGP

VGA PCI Audio, PCI IDE and Super

Multi-I/O

FeaturesMVP4G

Page 2

FEATURES

MVP4G Features:

•Intel Pentium®Processor, Pentium Processor with MMX technology, AMD

K5/K6, Cyrix 6x86L/6x86MX &idt C6 operating at 133 ~ 450 MHzwith

321 ZIF socket 7provides scalability to accept faster Processors in the

future.

•Designed with VIA MVP4 AGPset.

•Supports up to 768 Mega of DRAM (minimum of 16 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at

66MHz or 100MHz

•Supports (1) 16 bit ISA slots, (4) 32 bit PCI slots, (1)AMR and provides

(2) independent high performance PCI IDE interfaces capable of supporting PIO

Mode 3/4 and Ultra DMA 33/66 devices. The MVP4G supports (2) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configurationconfusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

•Designed with lntegrated Multi I/O: (1) floppy port, (1) parallel port (EPP,

ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released.

•MVP4G utilizes a Lithium battery which provides environmental protection

and longer battery life.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

FeaturesMVP4G

Page 3

•Resume by Alarm - Allows your system to turn on at a preselected time.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Keyboard power ON function (KBPO).

•Supports USDM software to offer motherboard various status.

•Supports the CPU and Chassis fan Auto stop in sleep mode.

•Built-in WOL (Wake On LAN)Connector.

• Built-inSoundBlaster/DirectSoundAC97Audio.

• Built-inAGP2D/3DGraphicsAccelerator.

InstallationMVP4G

Page 4

Figure 1

MVP4G Detailed Layout

PCI Slot #2

PCI Slot #3

PCI Slot #4

AMR

Battery

VIA

VT8501

VIA

VT82C686A

COM 1

USB

VGA

Parallel Port

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

PS/2 Keyboard

(Bottom)

IDE1

Secondary IDE

FDD1

Flash Memory

for BIOS

J7:WOL

Game Port

SOCKET 7

JP4

DIMM 3 Bank 2

DIMM 2 Bank 1

DIMM 1 Bank 0

CPU FAN

ISA Slot #1

PCI Slot #1

JP3

POWER_ON/OFF

SPK

Power LED

RESET

IR CONN.

Chassis FAN

JP1

COM2

USB CONN.

CD1

AUX1

IDE2

InstallationMVP4G

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers to match your hardware

Install memory chips

Device Connectors

Configure Jumpers

We design this motherboard with the fewest jumpers to make your install fast and

easy.

The following will describe all of the jumpers that you are required to set before

moving on to step 2.

Note: The jumpers as depicted as shown (Figure 1) in their correct physi-

cal orientation.

JP4KeyboardPower-ONfunction(referto thesection3-4)

JP4=1-2 -

=2-3- Disabled(Default)

Enabled

J7WOL(Wake On

LAN)

Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

JP1 = 1-2 - Run Mode (Default)

= 2-3 - Clear CMOS (momentarily)

JP1 CMOS Clear

InstallationMVP4G

Page 6

1234

SW 1 CPU

Vcore

2345

ON 1.8V

2.0V

2.1V

ONON ON

2.2V

2.3V

2.4V

3.2V

2.9V

2.8V

ONON ON ON

SW1: CPU Vcore Selection

JP3: CPU Speed Selection

XMM/muitneP 6K/5KDMA 6C-TDI

3PJ

MBI/xiryC IIM/XM68x6

reilpitluMkcolCsuB

zHM661

X5.2

zHM66002RP

zHM57332RP

zHM38662RP

zHM59003RP

zHM052zHM001663RP

ZHM002

zHM66662RP

zHM57003RP

zHM052zHM38333RP

zHM59004RP*

zHM003zHM001334RP*

zHM332

X5.3

zHM66003RP

zHM57333RP

zHM38004RP*

zHM333zHM59664RP*

zHM053zHM001005RP*

zHM662

zHM66333RP

zHM57004RP

zHM333zHM38664RP*

zHM083zHM59335RP*

zHM004zHM001055RP*

zHM003

X5.4

zHM66

zHM054zHM001

zHM333

zHM66

zHM574zHM59

zHM005zHM001

zHM663X5.5zHM66

*Reserved

InstallationMVP4G

Page 7

System Memory Configuration

Memory Layout

The MVP4G supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

•We recommend using SDRAM DIMM can not mixing

with EDO DIMM modules.

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or

125MHz (-8ns) bus speed.

• No Registered DIMM support.

Figure 2 and Table 1 show several possible memory configurations using

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

Table 1

DIMM 1

DIMM 2

Bank 0

Bank 1 -Synchronous

-EDO

DIMM 3

Bank 2

yromeMlatoT 1MMID )0knaB( 2MMID )1knaB( 3MMID )2knaB(

BM821= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 1XBM821,BM46 enoNenoN

BM652=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46 enoN

BM483=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

InstallationMVP4G

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connections

(figure 6).

J4:CPU Fan Power

• A plug-in for the CPU Fan Power

J6:Chassis Fan Power

• A plug-in for the chassis Fan Power

J7:WOL (Wake On LAN) Connector

PW1:ATX Power Connector

• 20-pin power connector

J2,J3:Chassis Panel Connector

• Power_LED, Speaker, Reset, Sleep, Turbo LED and HDD LED

IDE1:Primary IDE Connector

IDE2:Secondary IDE Connector

FDD1:Floppy Controller Connector

CD1:MITSUMI CD-ROM Audio_in

AUX1:Extra CD Audio Connector

COM2: RS232 COM2 Connector

USB CONN.: The third and fourth USB port (cable optional)

PS/2 Mouse

PS/2

KEYBOARD

COM1 VGA1

parallel port

Speaker

Joystick/Midi port

USB port

Line_in

MIC

Figure 6

InstallationMVP4G

Page 9

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either

Instant Off (turns system off immediately),or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off). When

the system is in 4 sec delay mode, we has added a special feature to

make the system go into suspend mode when the button is pressed

momentarily.

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is

activate

Power LED connector

1. Power LED(+) 4. NC

2. N/C 5. GND

3. GND

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Tabla de contenidos

Otros manuales de Placa madre de EPOX

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario