EPOX MVP4F Manual de usuario

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 1.0

August 9, 1999

MVP4F

ISA/PCI Motherboard with Onboard AGP

VGA, PCI Audio, PCI IDE and Super

Multi-I/O

FeaturesMVP4F

Page 2

FEATURES

MVP4F Features:

•Intel Pentium®Processor, Pentium Processor with MMX technology,

AMD K6/K6-2/K6 III, Cyrix 6x86MX/MII,IDT C6/Winchip, and Rise mp6

series operating at 133 ~ 500MHz with 321 ZIF socket 7provides

scalability to accept faster Processors in the future.

•Designed with VIA MVP4 AGPset.

•Supports up to 256 MB of DRAM (minimum of 8 MB) on board,

You can use 168-pin DIMM x 2.

•Supports (2) 32 bit PCI slots, (1) AMR Slot and provides (2) independent

high performance PCI IDE interfaces capable of supporting PIO Mode 3/4

and Ultra DMA 33/66 devices. The MVP4F supports (2) PCI Bus Master

slots and a jumperless PCI INT# control scheme which reduces configura-

tion confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

•Designed with lntegrated Multi I/O: (1) floppy port, (1) parallel port

(EPP,ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com

please visit our Technical Support section for the latest updates)

•MVP4F utilizes a Lithium battery which provides environmental

protection and longer battery life.

• Software power-down when using Windows®95/98.

FeaturesMVP4F

Page 3

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

•Resume by Alarm - Allows your system to turn on at a preselected time.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports USDM software to offer motherboard various status.

•Built-in WOL (Wake On LAN) Connector.

• Built-in Sound Blaster Compatible/DirectSound AC97 Audio.

• Built-in AGP 2D/3D Graphics Accelerator.

InstallationMVP4F

Page 4

Figure 1

MVP4F Detailed Layout

InstallationMVP4F

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers

System Memory Configuration

Device Connectors

Configure Jumpers

We design this motherboard with the fastest jumpers to make your install fast and

easy.

Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation.

1WS suB kcolC

1234

NOzHM66

NOzHM57

NONOzHM38

NONOzHM09

NONOzHM59

NONONOzHM001

NONONOzHM501

NONONOzHM511

1WS UPC

reilpitluM

6CTDI/xiryC/DMA

UPC

reilpitluM

2pihCniWTDI

567

NOX2

NONOX5.2

NOX3

X5.3

NONOX4

NONONOX5.4

NONOX533.2

NOX5.566.2

JP2: CPU Vcore Voltage Selection

SW1: CPU Speed Selection

2PJerocVUPC

7-1V0.2

8-2V2.2

9-3V4.2

01-4V8.2

11-5V9.2

21-6V2.3

SW1

2.0V

2.2V

2.4V

2.8V

2.9V

3.2V

JP2

InstallationMVP4F

Page 6

* Reserved

CPUTypeSW1CPU

Bus

Clock

CPU

Multiplier

Pentium/MMX

AMDK6/K6-2/K6III

IDT-C6

Cyrix/IBM

6x86MX/MIIIDTWinchip 2Rise MP61234567

166MHzPR200ONONON66MHz

2.5X

PR233ONONON75MHz

PR266233MHzONONONON83MHz

PR300*PR333ONONONON95MHz

250MHzPR366300MHz*PR366ONONONONON100MHz

200MHzPR266200MHzONON66MHz

PR300225MHzONON75MHz

250MHzPR333266MhzONONON83MHz

PR400*PR380ONONON95MHz

300MHz*PR433*PR400ONONONON100MHz

233MHzPR300233MHzON66MHz

3.5X

PR333ON75MHz

*PR400ONON83MHz

333MHz*PR466*PR433ONON95MHz

350MHz*PR500*PR466ONONON100MHz

266MHz*PR333266MHzONONON66MHz

*PR400ONONON75MHz

333MHz*PR466ONONONON83MHz

380MHz*PR533ONONONON95MHz

400MHz*PR550ONONONONON100MHz

300MHzONONONON66MHz4.5X

450MHzONONONONONON100MHz

333MHzONONON66MHz

5X475MHzONONONON95MHz

*500MHz266MHzONONONONON100MHz

366MHzONON66MHz5.5X

*550MHz300MHzONONONON100MHz

WOL(Wakup OnLAN)Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

InstallationMVP4F

Page 7

System Memory Configuration

Memory Layout

The MVP4F supports (2) 168-pin DIMMs (Dual In-line Memory Module).

The DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using

yromeMlatoT 1MMID )1/0knaB( 2MMID )3/2knaB(

BM821= mumixaM

*MARDS/ODE ,BM46,BM23,BM61,BM8 1XBM821 enoN

BM652= mumixaM

*MARDS/ODE ,BM46,BM23,BM61,BM8 1XBM821

DIMM 1

DIMM 2

Bank 0/1

Bank 2/3 -Synchronous

-EDO

Figure 2

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

* We recommend to use PC100 Memory Module for bus speed between

66MHz and 100MHz.

Table 1

InstallationMVP4F

Page 8

Device Connectors

Please install the motherboard into the chassis.

PS/2 Mouse

PS/2

KEYBOARD

COM1VGA1

parallel port

Speaker

Joystick/Midi

USB port

Line_in

MIC

Figure 6

J2:Chassis Panel Connector

• Power LED, Speaker, Reset

J3:Power_ON/OFF, Turbo LED, HDD LED, IR Connector

J4:CPU Fan Power

• A plug-in for the CPU Fan Power

J6:Chassis Fan Power

• A plug-in for the chassis Fan Power

J7:WOL (Wake On LAN) Connector

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD-ROM Audio_in Connector

MODEM1: Telephony Connector

• Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem)

InstallationMVP4F

Page 9

Device Connectors(continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker3. GND

2. N/C4. GND

Reset - Closed to restart system.

Power LED - Power LED connector

1. Power LED(+)4. NC

2. N/C5. GND

3. GND

(This is connected to the power button on the case. Using the

Soft-Off by Pwr-BTTN feature, you can choose either Instant

Off (turns system off immediately), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off).

When the system is in 4 sec delay mode, there is a special feature

to make the system to go into suspend mode when the button is

pressed momentarily.)

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard

disks is activate

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Power On/Off

Tabla de contenidos

Otros manuales de Placa madre de EPOX

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario