EOS 94 3742 Guía de instalación

Druck Nr. 29343125en/ 50.06

Assembly instructions and

instructions for use

Infrared Heating Foils

MADE INGERMANY

2GB

Caution!

If you suffer from any type of

skin disease or notice any changes

consult a physician under all

circumstances.

Importantnotes:

Theheatingfoilsposeafirehazardwhen

not installed properly. Please read these

installation instructions thoroughly. Pay

particular attention to the dimensions

specifiedandthefollowinginstructions:

lThe infrared heating foils are designed for

connectionto230V50Hzoveraninfrared

control unit.

lInstall and connect the infrared control unit

according to the connection schematic.

lBefore putting the foils into operation with

the control unit, ensure that all plug

connectors are connected so they cannot

loosen.

lObserve regulations in EU 60335-2-53

(VDE 0700 Part 53) inside the infrared

booth.

lInstall only the number of heating foils in

the infrared heat booth specified for the

booth size.

lUse one of the control units specified

below for control of the infrared radiators.

Install this control unit on the infrared heat

booth as specified in the installation

instructions for the control unit.

lInstall the heating foils in the booth to

achieve uniform heat radiation all around

for the person in the booth.

lThe infrared heating foils are not suitable

for installation in the booth ceiling and

should not be installed there.

lNote that the energy is output primarily in

the form of infrared radiation.

lThe infrared heating foils are equipped

with a silicone connection cable with

three-pin plug. Connect this plug to a

free outlet on the connector for the IR

control unit.

Whenconnectingensurethatthecircuit

breaker is secured against

unintentionalactuation.

lOn a standard basis five infrared heating

foils can be connected to this plug-in

distribution.Donotexceedthemaximum

power of 3500 W.

It is most practical to attach the plug

connector to the ceiling of the booth.

lNever cut open heating foils open or in

two.Operateonlyinthefixeddimensions

available.

lThis device has not been designed for

being used by persons (including

children) that are physically or mentally

handicapped or have sensory

disabilities. Moreover, it is not allowed

to use this device without sufficient

experience and/or knowledge, unless

these persons will be supervised by

persons responsible for their security

or in case they have been instructed

how to use this device.

lChildren are to be supervised in order to

make sure that they do not play with this

device.

Design and installation of IR foils (heating mats):

Polyester foil / Polyester foil with aluminum

heating element, heavy-metal free,

excessive temperature thermostat at upper

end of foil in silicone housing

Switch-off point = 120 °C

Switch-on point = 110 °C

40 mm wide edge without heating filaments

all the way around for fastening foil.

Channeled

boards on

outside

Insulation

Channeled

boards on

inside

Heat radiation

Layout

Operating principle

Provide for opening for

silicone housing for

excessive temperature

thermostat

Heating area

of foil

40 mm wide

fastening

edge all the

way around

The IR heating foils are intended only for

installation in the infrared heat booth and

should be operated only in combination

with a control unit.

Any other type of use invalidates the

guarantee.

Example of arrangement

Outer wall

Inner shell

recommanded

inner wall

dept < 12mm

component-frame

IR Heating foil

Caution!

4GB

Caution! Never drive fastening

elements (staples, pins, nails or

screws) through the aluminum

heating filaments

If the heating filament is interrupted, the

heating foil no longer heats up!

When installing the silicone housing always

ensure that the protective thermostat points

up.

Never screw in screws in the area of the

heating foils during final installation.

Caution! Observe maximum

switchingpowerforcontrolunit.

Electricalconnection

Feedline

Control unit Plug IR heating foils

max. 3500 W distribution

650 W

550 W

Take appropriate measures for pull relief on

the feed lines for the foils (cable clamps). Plug

theconnectionplugsfortheIRheatingfoilsinto

the distribution block on the control unit.

When installing route the connection leads

through the empty conduit or take other

suitable measures to prevent damage.

Usethecontrolunit60IR,48IRor EMOTEC

HIC75.

Start-up

Start up with the associated control unit.

Note that this heating system has a certain

"time delay". It is first necessary for the foils

to heat up the channeled boards in front,

before they can radiate heat into the booth.

Itisquitepossible for the temperature at the

surface of the wood on the inside of the

booth to be higher than the room

temperature inside the booth.

Theprimaryeffectoftheinfraredheatbooth

is its capability of radiating (infrared) heat to

humans; the heat resulting in the room is a

secondary, ancillary effect, which is,

however, experienced as pleasant and

does not have any negative effect on the

treatment.

Please observe, that the IR heat booth is

notasaunawithtypicalhot/coldtreatments

and that the temperatures present in a

sauna cannot be achieved!

Possible connection schematic

Guarantee

Theguaranteeistakenoveraccordingtothelegal

regulations at present.

Manufacturer’s warrenty

- The period of warrenty starts from the date of

purchase and lasts up to 2years for commercial

use and 3 years for private use.

- Alwaysincludethecompletedwarrentycertificate

when returning equipment.

- The warrenty expires for appliances which have

been modified without manufacturer’s explicit

agreement.

- Damages caused by incorrect operation or

handlingthroughnon-authorizedpersonsarenot

covered under the terms of warranty.

- In the event of a claim, please indicate the serial

number as well as the article code number and

type name with expressive description of the

fault.

- This warrenty covers damaged parts but no

defects due to wear and tear.

Incase of complaint please returnthe equipment in

its original packaging or other suitable packaging

(caution:dangeroftransportdamage)toourservice

department.

Always include the completed warrenty certificate

when returning equipment.

Possibleshipping costsarisingfromthetransport

to and from point of repair cannot be borne by us.

Outside of Germany please contact your special-

ist dealer in case of warranty claims. Direct

warranty processing with our service department

is in this case not possible.

Equipment start-up date:

Stampandsignatureoftheauthorizedelectrician:

Service address:

EOS-Werke Günther GmbH

Adolf-Weiß-Straße 43

35759 Driedorf, Germany

Tel. +49 (0)2775 82-240

Fax +49 (0)2775 82-455

[email protected]

www.eos-werke.de

Technical data:

Voltage: 230 V 50Hz

Type 1 Art.No.: 94 3742

Output: 650 W

Dimensions foil: 1700 x 800 mm

Dimensions heating

surface: 1620 x 720 mm

Type 2 Art.No.: 94 3743

Output: 550 W

Dimensions foil:: 1450 x 800 mm

Dimensions heating

surface: 1370 x 720 mm

Type 3 Art.No.: 94 3744

Output: 450 W

Dimensions foil: 1600 x 600 mm

Dimensions heating

surface: 1520 x 520 mm

Type 4 Art.No.: 94 3745

Output: 350 W

Dimensions foil: 1250 x 600 mm

Dimensions heating

surface: 1170 x 520 mm

Type 5 Art.No.: 94 3835

Output: 275 W

Dimensions foil: 1600 x 400 mm

Dimensions heating

surface: 1520 x 320 mm

Type 6 Art.No.: 94 3891

Output: 90 W

Dimensions foil: 600 x 300 mm

Dimensions heating

surface: 520 x 220 mm

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de EOS

EOS

EOS SteamTec Premium Manual de usuario

EOS

EOS IRS 35 RHK Guía de planificación

EOS

EOS EOS Selection Manual de usuario

EOS

EOS Cubo Guía de planificación

EOS

EOS Moment W Guía de planificación

EOS

EOS Bi-O Mat U Guía de planificación

EOS

EOS 43.HB Guía de planificación

EOS

EOS 43.FN Guía de planificación

EOS

EOS Mega Manual de usuario

EOS

EOS 38.AS Guía de instalación

EOS

EOS Bi-O Thermat Guía de planificación

EOS

EOS Majesty Manual de usuario

EOS

EOS M3 Guía de planificación

EOS

EOS Finnrock 94.5664 Manual de usuario

EOS

EOS Stativ Terra Vita II Manual de usuario

EOS

EOS Mega S HD Manual de usuario

EOS

EOS Vitae Compact Guía del usuario

EOS

EOS Edge Control Manual de usuario

EOS

EOS Bi-O Invisio Guía de planificación

EOS

EOS Filius Control Guía del usuario

EOS

EOS Skiff Manual de usuario

EOS

EOS Zeus Manual de usuario

EOS

EOS Cubo 2 Guía del usuario

EOS

EOS IRS 30 Keramik Guía de planificación

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario