Endress+Hauser ITEMP Pt TMT180 Manual de usuario

BA163R/24/ae/07.06

51006606

Operating instructions

iTEMP®Pt TMT180

Temperature head transmitter

Safety message TMT180

2Endress+Hauser

Safety message

Instructions and procedures in the operating instructions may require special precautions to ensure

the safety of the personnel performing the operations. Information that potentially raises safety

issues is indicated by safety pictograms and symbols. Please refer to the safety messages before

performing an operation preceded by pictograms and symbols, see chapter 1.5.

Though the information provided herein is believed to be accurate, be advised that the information

contained herein is NOT a guarantee of satisfactory results. Specifically, this information is neither

a warranty nor guarantee, expressed or implied, regarding performance; merchantability, fitness, or

other matter with respect to the products; and recommendation for the use of the product / process

information in conflict with any patent. Please note that the manufacturer reserves the right to

change and / or improve the product design and specifications without notice.

#Warning!

Failure to follow these installation guidelines could result in death or serious injury.

– Make sure only qualified personnel perform the installation.

Process leaks could result in death or serious injury.

– Do not remove the thermowell while in operation.

– Install and tighten thermowells and sensors before applying pressure.

Electrical shock could cause death or serious injury.

– Use extreme caution when making contact with the leads and terminals.

Brief overview

Using the following short form instructions you can commission your system easily and swiftly:

Safety notes →Page 4

⇓

Installation →Page 7

⇓

Wiring →Page 10

⇓

Display and operating elements

Preparing the communication with PC configuration software

→Page 12

⇓

Instrument configuration (including a description of the unit

functions)

A complete description of all the functions as well as a detailed overview of

the functionality can be found in this chapter.

→Page 13

TMT180 Table of contents

Endress+Hauser 3

Table of contents

1 Safety notes . . . . . . . . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning and operation . . . . . . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5 Safety pictograms and symbols . . . . . . . . . . . . . . . . . 5

2 Identification . . . . . . . . . . . . . . . . . . . . 6

2.1 Unit identification . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 7

3 Installation . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 10

4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.2 Measurement unit connection . . . . . . . . . . . . . . . . 10

4.3 Potential grounding . . . . . . . . . . . . . . . . . . . . . . . . 11

4.4 Ground the Transmitter . . . . . . . . . . . . . . . . . . . . . 11

5 Operation . . . . . . . . . . . . . . . . . . . . . . 12

5.1 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Commissioning. . . . . . . . . . . . . . . . . . 13

6.1 Installation and function check . . . . . . . . . . . . . . . 13

6.2 Switch on the device . . . . . . . . . . . . . . . . . . . . . . . 13

6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Maintenance. . . . . . . . . . . . . . . . . . . . 15

8 Accessories. . . . . . . . . . . . . . . . . . . . . 15

9 Trouble-shooting . . . . . . . . . . . . . . . . 16

9.1 Trouble-shooting instructions . . . . . . . . . . . . . . . . 16

9.2 Application errors without messages . . . . . . . . . . . 16

9.3 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

9.4 Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

9.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

9.6 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . 17

10 Technical Data . . . . . . . . . . . . . . . . . . 18

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Safety notes TMT180

4Endress+Hauser

1 Safety notes

Safe and secure operation of the head transmitter can only be guaranteed if the operating

instructions and all safety notes are read, understood and followed.

1.1 Designated use

• The unit is a universal, presettable temperature head transmitter for resistance thermometer

(RTD). The unit is constructed for mounting in a connection head (DIN form B) or field housing.

• The manufacturer cannot be held responsible for damage caused by misuse of the unit.

1.2 Installation, commissioning and operation

The unit is constructed using the most up-to-date production equipment and complies to the safety

requirements of the local guidelines. The temperature transmitter is fully factory tested according to

the specifications indicated on the order. However, if it is installed incorrectly or is misused, certain

application dangers can occur. Installation, wiring and maintenance of the unit must only be done

by trained, skilled personnel who are authorized to do so by the plant operator. This skilled staff

must have read and understood these instructions and must follow them to the letter. The plant

operator must make sure that the measurement system has been correctly wired to the connection

schematics.

Electrical temperature sensors such as RTD's produce low-level signals proportional to their sensed

temperature. The temperature transmitter converts the low-level sensor signal to a standard 4 to 20

mA DC signal that is relatively insensitive to lead length and electrical noise. This current signal is

then transmitted to the control room via two wires.

The transmitter electronics module is permanently sealed within the housing, resisting moisture and

corrosive damage. Verify that the operating atmosphere of the transmitter is consistent with the

appropriate hazardous locations certifications.

#Warning!

Electrical shock could cause death or serious injury. If the sensor is installed in a high voltage

environment and a fault or installation error occurs, high voltage may be present on the transmitter

leads and terminals.

Temperature Effects

The transmitter will operate within specifications for ambient temperatures between -40 and

185 °F (-40 and 85 °C). Heat from the process is transferred from the thermowell to the transmitter

housing. If the expected process temperature is near or beyond specification limits, consider the use

of additional thermowell lagging, and extension nipple, or a remote mounting configuration to

isolate the transmitter from the process.

TMT180 Safety notes

Endress+Hauser 5

1.3 Operational safety

The measuring device complies with the general safety requirements in accordance with IEC61010,

the EMC requirements of IEC61326 and NAMUR recommendation NE21 and NE43.

Technical advancement

The manufacturer reserves the right to modify technical data without prior notice. Your distributor

can supply you with current information and updates to these Operating Instructions.

1.4 Returns

Please follow the Return Authorization Policy.

1.5 Safety pictograms and symbols

Safe and reliable operation of this unit can only be guaranteed if the safety notes and warnings in

these operating instructions are followed. The safety notes in these instructions are highlighted

using the following symbols.

!Note!

This icon indicates activities and actions that, if not followed correctly, could have an indirect

influence on the unit operation or could lead to an unforeseen unit reaction.

"Caution!

This icon indicates activities and actions that, if not followed correctly, could lead to faulty device

operation or even damage to the unit.

#Warning!

This icon indicates activities and actions that, if not followed correctly, could lead to personal injury,

a safety risk or even total damage to the unit.

120

Explosion protected, type examined operating equipment!

If one of these icons is on the device’s nameplate, the device can be used in hazardous areas.

-Hazardous area!

This symbol identifies the hazardous area in the diagrams in these Operating Instructions.

– Devices that are used in hazardous areas or cables for such devices must have the corresponding

type of protection.

.Safe area (non-hazardous areas)!

This symbol identifies the non-hazardous area in the diagrams in these Operating Instructions.

– Devices in non-hazardous areas must also be certified if connection cables run through a

hazardous area.

Identification TMT180

6Endress+Hauser

2 Identification

2.1 Unit identification

2.1.1 Legend plate

Compare the legend plates on the head transmitter with the following figures:

Fig. 1: Example: Head transmitter legend plate

Fig. 2: Order code with configuration (example) - K = Standard model, North America region

CE Mark, declaration of conformity 4

The devices are designed to meet state-of-the-art safety requirements, have been tested, and left the

factory in a condition in which they are safe to operate. The devices comply with the applicable

standards and regulations in accordance with IEC61010 "Protection Measures for Electrical

Equipment for Measurement, Control, Regulation and Laboratory Procedures" and with the EMC

requirements of IEC61326.The measuring system described in these Operating Instructions thus

complies with the statutory requirements of the EC Directives. The manufacturer confirms

successful testing of the device by affixing to it the CE mark.

UL recognized component to UL 3111-1 â

CSA GP approved

GL German Lloyd marine approval Ó

GL Type Approval for temperature measurements in hazardous locations on GL Classed Vessels,

Marine and Offshore Installations.

TMT180 Installation

Endress+Hauser 7

2.2 Delivery contents

The delivery contents of the temperature head transmitter are as follows:

• Temperature head transmitter

• Installation screws, installation springs and E-rings

• Operating instructions

!Note!

Please take note of the head transmitter accessories in chapter 8 "Accessories".

2.3 Registered trademarks

•iTEMP

®and ReadWin®2000

are registered trademarks of Endress+Hauser Wetzer GmbH + Co. KG, Nesselwang, Germany

3 Installation

3.1 Installation conditions

• When installing and operating the unit, please take note of the allowable ambient temperature

(see chapter 10 "Technical Data").

3.1.1 Dimensions

The head transmitter dimensions can be found in chapter 10 "Technical data".

3.1.2 Installation point

• Sensor connection head to DIN 43 729 Form B

• Field housing

3.1.3 Installation angle

There are no limits as to the angle of installation.

Installation TMT180

8Endress+Hauser

3.2 Installation

3.2.1 Typical European installation

For installation, proceed as follows:

Installing in a sensor connection head to DIN 43 729 Form B (see Fig. 3)

• Feed the sensor inset cables (Pos. 5) through the central hole in the head transmitter (Pos. 4).

• Place the installation springs (Pos. 3) onto the screws (Pos. 2).

• Feed the installation screws (Pos. 2) through the holes in the head transmitter and the holes in

the sensor inset (Pos. 5). Fix both screws using the E-rings (Pos. 6).

• Position the head transmitter in the connection head in such a way that the current output

terminals (terminal 1 and 2) are towards the cable entry gland (Pos. 7).

• Fix the head transmitter (Pos. 4) and sensor inset (Pos. 5) into the connection head.

Installation in a field housing (see Fig. 4)

• Feed the installation screws (Pos. 2) with installation springs (Pos. 3) through the holes in the

head transmitter (Pos. 4). Fix these using the E-rings (Pos. 5).

• Screw the head transmitter into the field housing using a screwdriver.

"Caution!

In order to avoid damaging the head transmitter, do not over-tighten the installation screws.

Fig. 3: Installation of head transmitter into a Form B

sensor connection head.

Fig. 4: Installation of head transmitter into field

housing.

TMT180 Installation

Endress+Hauser 9

3.2.2 Typical North American installation

Industrial thermocouple or RTD assembly with head transmitter (see Fig. 5)

• Attach the thermowell (Pos. 1) to the pipe or process container wall. Install and tighten

thermowells before applying process pressure.

• Attach necessary extension nipples and adapters (Pos. 3) to the thermowell. Seal the nipple and

adapter threads with silicone tape.

• Install drain seals if required for severe environments or to satisfy code requirements.

• Feed the installation screws (Pos. 6) through the holes in the head transmitter (Pos. 7).

• Position the head transmitter assembly in the transmitter housing (Pos. 4) in such a way that the

current output terminals (terminal 1 and 2) are towards the conduit.

• Screw the head transmitter assembly (Pos. 5) into the the transmitter housing (Pos. 4) using a

screwdriver. Max.torque ¾ pound-feet (1 Nm).

• Feed the sensor inset cables through the conduit of the transmitter housing and the central hole

in the head transmitter.

• Attach the transmitter housing (Pos. 4) with built-in head transmitter assembly to the nipples and

adapters (Pos. 3). Seal adapter threads with silicone tape.

"Caution!

In order to avoid damaging the head transmitter, do not over-tighten the installation screws.

"Caution!

Pull the field wiring leads through the conduit into the transmitter housing. Attach the sensor and

power leads to the head transmitter. Avoid contact with other terminals.

"Caution!

Install and tighten the transmitter housing cover. Enclosure covers must be fully engaged to meet

explosion-proof requirements.

Fig. 5: Installing the head transmitter - Head transmitter assembly

Pos. 1: Thermowell

Pos. 2: Measuring inset

Pos. 3: Extension neck

Pos. 4: Transmitter housing

Pos. 5: Head transmitter assembly

Pos. 6: Installation screws

Pos. 7: Head transmitter

Wiring TMT180

10 Endress+Hauser

4 Wiring

4.1 Overview

Terminal layout

Fig. 6: Head transmitter wiring

4.2 Measurement unit connection

"Caution!

• Switch off power supply before opening the housing cover. Do not install or connect the unit to

power supply. If this is not followed parts of the electronic circuit will be damaged.

• If the device has not been grounded as a result of the housing being installed, we recommend

grounding it via one of the ground screws.

•Sensors:

Connect the sensor cables to the respective head transmitter terminals (Terminals 3 to 6) by

following the wiring diagram (see Fig. 6).

•Output signal and power supply:

Open the cable gland on the sensor head or field housing. Feed the cable through the opening in

the cable gland and then connect the cable cores to terminals 1 and 2 according to the wiring

diagram (see Fig. 6).

•PC configuration (SETUP socket):

Open the flap on the SETUP socket (see Fig. 6) and connect the SETUP connection cable.

Fig. 7: Connection to PC for configuration

Tabla de contenidos

Otros manuales de Transmisor de Endress+Hauser

Endress+Hauser

Endress+Hauser iTEMP TMT31 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 digital PROFIBUS DP Especificaciones técnicas

Endress+Hauser

Endress+Hauser HART Flowmeter Proline 400 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar M PMD55 Manual de usuario

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT82 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 300 Modbus RS485 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Instrucciones de funcionamiento e instalación

Endress+Hauser

Endress+Hauser cerabar S PROFIBUS-PA Manual de usuario

Endress+Hauser

Endress+Hauser RMA42 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar S FMD76 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual

Endress+Hauser

Endress+Hauser tmt142 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Cerabar M Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 PROFIBUS PA Especificaciones técnicas

Endress+Hauser

Endress+Hauser mycom COM 121 Manual de usuario

Endress+Hauser

Endress+Hauser CM14 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 digital Modbus RS485 Especificaciones técnicas

Endress+Hauser

Endress+Hauser CUM 740 Manual de usuario

Endress+Hauser

Endress+Hauser TMD1000 Manual de usuario

Endress+Hauser

Endress+Hauser Liquisys M COM 223 F Manual de usuario

Endress+Hauser

Endress+Hauser AT1000 AT1 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Endress+Hauser iTEMP Pt TMT180 Manual de usuario

Manuales populares de Transmisor de otras marcas