Endress+Hauser ITEMP PCP TMT 121 Manual de usuario

BA 156R/24/ae/08.03

51006707 iTEMP®PCP TMT 121

Temperature DIN rail transmitter

Operating instructions

Temperature DIN rail transmitter

2Endress+Hauser

Safety message

Instructions and procedures in the operating instructions may require special precau-

tions to ensure the safety of the personnel performing the operations. Information that

potentially raises safety issues is indicated by safety pictograms and symbols. Please

refer to the safety messages before performing an operation preceded by pictograms

and symbols, see chapter 1.5.

Though the information provided herein is believed to be accurate, be advised that the

information contained herein is NOT a guarantee of satisfactory results. Specifically, this

information is neither a warranty nor guarantee, expressed or implied, regarding

performance; merchantability, fitness, or other matter with respect to the products; and

recommendation for the use of the product / process information in conflict with any

patent. Please note that the manufacturer reserves the right to change and / or improve

the product design and specifications without notice.

#Warning!

Failure to follow these installation guidelines could result in death or serious

injury.

– Make sure only qualified personnel perform the installation.

Explosions could result in death or serious injury.

– Do not remove the connection head cover in explosive atmospheres when the circuit

is live.

– Configuration of the transmitter is not permitted in a hazardous area, make sure the

transmitter setup is done before the transmitter will be installed in hazardous area.

– Verify that the operating atmosphere of the transmitter is consistent with the appro-

priate hazardous locations certifications.

– All connection head covers must be fully engaged to meet explosion-proof require-

ments.

Process leaks could result in death or serious injury.

– Do not remove the thermowell while in operation.

– Install and tighten thermowells and sensors before applying pressure.

Electrical shock could cause death or serious injury.

– Use extreme caution when making contact with the leads and terminals.

Brief overview

Using the following short form instructions you can commission your system easily and

swiftly:

Safety notes Page 4

➪

Installation Page 7

➪

Wiring Page 10

➪

Display and operating elements

Preparing the communication with PC configuration software

Page 12

➪

Instrument configuration (including a description of the unit

functions)

A complete description of all the functions as well as a detailed

overview of the functionality can be found in this chapter.

Page 13

Temperature DIN rail transmitter Endress+Hauser

Endress+Hauser 3

Table of contents

1 Safety notes. . . . . . . . . . . . . . . . . . . . . 4

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Installation, commissioning and operation . . . 4

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . 5

1.4 Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5 Safety pictograms and symbols . . . . . . . . . . . 5

2 Identification. . . . . . . . . . . . . . . . . . . . 6

2.1 Unit identification . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Delivery contents . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Registered trademarks . . . . . . . . . . . . . . . . . . 7

3 Installation . . . . . . . . . . . . . . . . . . . . . 7

3.1 Installation conditions . . . . . . . . . . . . . . . . . . . 7

3.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 10

4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.2 Measurement unit connection . . . . . . . . . . . . 10

4.3 Ground the Transmitter . . . . . . . . . . . . . . . . . 11

5 Operation. . . . . . . . . . . . . . . . . . . . . . 12

5.1 Communication . . . . . . . . . . . . . . . . . . . . . . . 12

6 Commissioning. . . . . . . . . . . . . . . . . 13

6.1 Installation and function check . . . . . . . . . . . 13

6.2 Switch on the device . . . . . . . . . . . . . . . . . . . 13

6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Maintenance . . . . . . . . . . . . . . . . . . . 16

8 Accessories . . . . . . . . . . . . . . . . . . . . 16

9 Trouble-shooting . . . . . . . . . . . . . . . 17

9.1 Trouble-shooting instructions . . . . . . . . . . . . 17

9.2 Application errors without messages . . . . . . 17

9.3 Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

9.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

9.5 Software history . . . . . . . . . . . . . . . . . . . . . . . 19

10 Technical Data . . . . . . . . . . . . . . . . 20

10.1 Function and system design . . . . . . . . . . . . 20

10.2 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

10.3 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

10.4 Power supply . . . . . . . . . . . . . . . . . . . . . . . . 22

10.5 Performance characteristics . . . . . . . . . . . . . 22

10.6 Installation conditions . . . . . . . . . . . . . . . . . . 23

10.7 Environmental conditions . . . . . . . . . . . . . . . 23

10.8 Mechanical construction . . . . . . . . . . . . . . . 24

10.9 Human interface . . . . . . . . . . . . . . . . . . . . . . 25

10.10 Certificates and approvals . . . . . . . . . . . . . . 25

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Safety notes Temperature DIN rail transmitter

4Endress+Hauser

1Safetynotes

Safe and secure operation of the DIN rail transmitter can only be guaranteed if the

operating instructions and all safety notes are read, understood and followed.

1.1 Designated use

•The unit is a universal, presettable temperature DIN rail transmitter for resistance

thermometer (RTD), thermocouple (TC) as well as resistance and voltage sensors.

The unit is constructed for mounting on a DIN rail.

•The manufacturer cannot be held responsible for damage caused by misuse of the

unit.

•Separate Ex documentation is part of this operating manual, for measurement sys-

tems in hazardous areas. The installation conditions and connection values indicated

in these instructions must be followed!

1.2 Installation, commissioning and operation

The unit is constructed using the most up-to-date production equipment and complies

to the safety requirements of the local guidelines. The temperature transmitter is fully

factory tested according to the specifications indicated on the order. However, if it is

installed incorrectly or is misused, certain application dangers can occur. Installation

and wiring of the unit must only be done by trained, skilled personnel who are

authorized to do so by the plant operator. This skilled staff must have read and

understood these instructions and must follow them to the letter. The plant operator

must make sure that the measurement system has been correctly wired to the

connection schematics.

Electrical temperature sensors such as RTD's and thermocouples produce low-level

signals proportional to their sensed temperature. The temperature transmitter converts

the low-level sensor signal to a standard 4 to 20 mA DC signal that is relatively

insensitive to lead length and electrical noise. This current signal is then transmitted to

the control room via two wires.

The transmitter needs to be commissioned before installation in a hazardous area.

Configuration of the device in explosion area is not allowed. Make sure the instruments

in the loop are installed in accordance with intrinsically safe or non-incendive field wiring

practices before connecting in an explosive atmosphere.

The transmitter electronics module is permanently sealed within the housing, resisting

moisture and corrosive damage. Verify that the operating atmosphere of the transmitter

is consistent with the appropriate hazardous locations certifications.

#Warning!

Electrical shock could cause death or serious injury. If the sensor is installed in a high

voltage environment and a fault or installation error occurs, high voltage may be present

on the transmitter leads and terminals.

Temperature DIN rail transmitter Safety notes

Endress+Hauser 5

1.3 Operational safety

Hazardous areas

When installing the unit in a hazardous area, the national safety requirements must be

met. Make sure that all personnel are trained in these areas. Strict compliance with

installation instructions and ratings as stated in this documentation is mandatory.

The measuring device complies with the general safety requirements in accordance

with IEC61010, the EMC requirements of IEC61326 and NAMUR recommendation NE21

and NE43.

Technical advancement

The manufacturer reserves the right to modify technical data without prior notice. Your

distributor can supply you with current information and updates to these Operating

Instructions.

1.4 Returns

Please follow the Return Authorization Policy at the end of these instructions. Due to its

construction, the transmitter cannot be repaired. When disposing of the transmitter,

please take note of the local disposal regulations.

1.5 Safety pictograms and symbols

Safe and reliable operation of this unit can only be guaranteed if the safety notes and

warnings in these operating instructions are followed. The safety notes in these

instructions are highlighted using the following symbols.

!Note!

This icon indicates activities and actions that, if not followed correctly, could have an

indirect influence on the unit operation or could lead to an unforeseen unit reaction.

"Caution!

This icon indicates activities and actions that, if not followed correctly, could lead to

faulty device operation or even damage to the unit.

#Warning!

This icon indicates activities and actions that, if not followed correctly, could lead to

personal injury, a safety risk or even total damage to the unit.

120

Explosion protected, type examined operating equipment!

If one of these icons is on the device’s nameplate, the device can be used in hazardous

areas.

-Hazardous area!

This symbol identifies the hazardous area in the diagrams in these Operating

Instructions.

– Devices that are used in hazardous areas or cables for such devices must have the

corresponding type of protection.

.Safe area (non-hazardous areas)!

This symbol identifies the non-hazardous area in the diagrams in these Operating

Instructions.

– Devices in non-hazardous areas must also be certified if connection cables run

through a hazardous area.

Identification Temperature DIN rail transmitter

6Endress+Hauser

2 Identification

2.1 Unit identification

2.1.1 Legend plate

Compare the legend plates on the DIN rail transmitter with the following figures:

Fig. 1: Example: DIN rail transmitter legend plate

Fig. 2: Identification for hazardous area use (example, only on FM certified units)

CE Mark, declaration of conformity 4

The devices are designed to meet state-of-the-art safety requirements, have been

tested, and left the factory in a condition in which they are safe to operate. The devices

comply with the applicable standards and regulations in accordance with IEC61010

"Protection Measures for Electrical Equipment for Measurement, Control, Regulation

and Laboratory Procedures" and with the EMC requirements of IEC61326.The

measuring system described in these Operating Instructions thus complies with the

statutory requirements of the EC Directives. The manufacturer confirms successful

testing of the device by affixing to it the CE mark.

UL recognized component to UL 3111-1

GL German Lloyd marine approval

GL Type Approval for temperature measurements in hazardous locations on GL

Classed Vessels, Marine and Offshore Installations.

Temperature DIN rail transmitter Installation

Endress+Hauser 7

2.2 Delivery contents

The delivery contents of the temperature DIN rail transmitter are as follows:

•Temperature DIN rail transmitter

•Operating instructions

•Control drawing for use in hazardous areas

!Note!

Please take note of the DIN rail transmitter accessories (Configuration Kit) in chapter 8

"Accessories".

2.3 Registered trademarks

•iTEMP®and ReadWin®2000

are registered trademarks of Endress+Hauser Wetzer GmbH + Co. KG, Nesselwang,

Germany

3 Installation

3.1 Installation conditions

•When installing and operating the unit, please take note of the allowable ambient

temperature (see chapter 10 "Technical Data").

•When using the unit in a hazardous area, the limits indicated in the certification must

be adhered to (see control drawing).

3.1.1 Dimensions

The DIN rail transmitter dimensions can be found in chapter 10 "Technical data".

3.1.2 Installation point

Installation on DIN rail according to EN 50 022-35, e.g. in control panel.

3.1.3 Installation angle

There are no limits as to the angle of installation.

Installation Temperature DIN rail transmitter

8Endress+Hauser

3.2 Installation

3.2.1 Typical North American installation

For installation, proceed as follows:

•Attach the TMT 121 transmitter to a suitable rail or panel.

•Attach thermowell (1) to pipe or process container wall. Install and tighten the ther-

mowell before applying process pressure.

•Attach necessary extension nipples and adapters (3) to the thermowell (1). Seal the

nipple and adapter threads with silicone tape.

•Screw the sensor (2) into the thermowell (1). Install drain seals if required for harsh

environments or to satisfy code requirements.

•Screw the connection head (4) to the sensor assembly.

•Attach the sensor lead wires to the connection head terminals.

•Connect sensor wires from the terminals inside the head to the TMT 121 transmitter

(5).

•Install and tighten the connection head cover. Enclosure covers must be completely

engaged to meet explosion-proof area requirements.

Fig. 3: Installation of DIN rail TMT 121 transmitter.

1 thermowell

2 sensor

3 extension nipples and adapters

4 connection head

5 TMT 121 transmitter

Temperature DIN rail transmitter Installation

Endress+Hauser 9

3.2.2 Typical European installation

For installation, proceed as follows:

•Attach the TMT 121 transmitter to a suitable rail or panel.

•Attach thermowell to pipe or process container wall. Install and tighten the thermowell

before applying any pressure.

•Attach and connect appropriate lengths of sensor lead wire from the connection head

to the sensor terminal block.

•Tighten the connection head cover. Enclosure covers must be completely engaged in

order to meet explosion-proof area requirements.

•Run the sensor lead wires from the sensor assembly to the TMT 121 transmitter.

•Attach the sensor wires to the TMT 121 transmitter.

Fig. 4: Installing the TMT 121 DIN rail transmitter

Wiring Temperature DIN rail transmitter

10 Endress+Hauser

4Wiring

4.1 Overview

Terminal layout

Fig. 5: DIN rail transmitter wiring

4.2 Measurement unit connection

"Caution!

•Switch off power supply before opening the housing cover. Do not install or connect

the unit to power supply. If this is not followed parts of the electronic circuit will be

damaged.

•If the device has not been grounded as a result of the housing being installed, we

recommend grounding it via one of the ground screws.

•Sensors:

Connect the sensor cables to the respective DIN rail transmitter terminals (Terminals

3 to 6) by following the wiring diagram .

•Output signal and power supply:

Connect the cable wires from the power supply to terminal 1 and 2 according to the

wiring diagram. For convenient installation, the connection is designed as a

removable plug, so the connection can be made on the terminals, then plug in the

connection socket to the transmitter housing.

!Note!

The screws on the terminals must be screwed in tightly.

•PC configuration (SETUP socket):

Connect the SETUP connection cable (see Fig. 5).

Tabla de contenidos

Otros manuales de Transmisor de Endress+Hauser

Endress+Hauser

Endress+Hauser iTEMP TMT84 Manual de usuario

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser easytemp TSM 470 G Manual de usuario

Endress+Hauser

Endress+Hauser CM14 Manual de usuario

Endress+Hauser

Endress+Hauser Liquisys M CLM223 Manual de usuario

Endress+Hauser

Endress+Hauser FHX50 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser tmt142 Manual de usuario

Endress+Hauser

Endress+Hauser HART iTEMP TMT182B Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT125 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline 500 digital HART Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser RMA42 Especificaciones técnicas

Endress+Hauser

Endress+Hauser iTEMP TMT71 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT71 Instrucciones de instalación

Endress+Hauser

Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 Manual de usuario

Endress+Hauser

Endress+Hauser Mycom S CPM 153 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manual de usuario

Endress+Hauser

Endress+Hauser CM14 Manual de usuario

Endress+Hauser

Endress+Hauser Liquisys M CUM 223 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Instrucciones de funcionamiento e instalación

Endress+Hauser

Endress+Hauser iTEMP TMT84 Especificaciones técnicas

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Endress+Hauser iTEMP PCP TMT 121 Manual de usuario

Manuales populares de Transmisor de otras marcas