Endress+Hauser CM14 Manual de usuario
Products Solutions Services
Operating Instructions
CM14
Transmitter, oxygen content
BA01033C/09/EN/02.14
71257167
Valid as of FW version:
02.00.xx
CM14 Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions .............. 4
1.1 Workplace safety .................... 4
1.2 Requirements concerning the staff ...... 4
1.3 Operational safety ................... 4
1.4 Designated use ...................... 5
1.5 Technical improvement ............... 5
1.6 Return ............................. 5
1.7 Notes on safety conventions and
icons ............................... 5
2 Identification .................... 7
2.1 Device designation ................... 7
2.2 Scope of delivery ..................... 7
2.3 Certificates and approvals ............. 8
3 Installation ...................... 9
3.1 Incoming acceptance, transport,
storage ............................. 9
3.2 Installation ......................... 9
3.3 Dimensions ......................... 9
3.4 Installation procedure ............... 10
3.5 Post-installation check ............... 10
4 Wiring .......................... 11
4.1 Connecting the transmitter ........... 12
4.2 Post-connection check ............... 13
5 Operation ...................... 14
5.1 Display and device status indicator/
LED ............................... 14
5.2 Local operation at the device .......... 14
5.3 Icons .............................. 15
5.4 Operating functions ................. 16
5.5 Hold function ...................... 16
6 Commissioning ................ 17
6.1 Installation check and switching on the
device ............................. 17
6.2 Display settings (Display menu) ....... 17
6.3 Configuration of the device (Setup
menu) ............................ 17
6.4 Extended configuration (Extended
setup menu) ....................... 18
6.5 Device diagnostics (Diagnostics menu) .21
7 Calibration ..................... 22
7.1 Definitions ......................... 23
7.2 Device functions for calibration ....... 24
8 Maintenance .................. 25
9 Accessories .................... 26
9.1 Sensors ........................... 26
10 Troubleshooting ............... 27
10.1 Troubleshooting instructions ......... 27
10.2 Diagnostic messages ................ 27
10.3 Spare parts ........................ 31
10.4 Return ............................ 31
10.5 Disposal ........................... 32
11 Technical data ................. 32
Index ................................. 40
Safety instructions CM14
4 Endress+Hauser
1 Safety instructions
Reliable and safe operation of the transmitter is guaranteed only if the user reads these
Operating Instructions and complies with the safety instructions they contain.
1.1 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
1.2 Requirements concerning the staff
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the
following requirements:
‣Trained, qualified specialists: must have a relevant qualification for this specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the instructions
in the Operating Instructions and supplementary documentation as well as in the
certificates (depending on the application)
‣Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the facility's
owner-operator
‣Following the instructions in these Operating Instructions
1.3 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
CM14 Safety instructions
Endress+Hauser 5
Environmental requirements
If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this
can damage the housing.
‣If you are unsure, please contact your Endress+Hauser Sales Center for clarification.
‣If used in an approval-related area, observe the information on the nameplate.
1.4 Designated use
The transmitter evaluates measured values of an analytical sensor and displays them on its
multicolor display. Processes can be monitored and controlled using the transmitter outputs
and limit relays. The device is equipped with a wide range of software functions for this
purpose.
• The manufacturer accepts no liability for damages resulting from incorrect use or use other
than that designated. It is not permitted to convert or modify the device in any way.
• The device is designed for installation in a panel and must only be operated in an installed
state.
1.5 Technical improvement
The manufacturer reserves the right to modify technical data without prior notice. Please
contact your sales center for information on modifications or updates to the Operating
Instructions.
1.6 Return
For a return, e.g. in case of repair, the device must be sent in protective packaging. The
original packaging offers the best protection. Repairs must only be carried out by your
supplier's service organization.
When returning the device for repair, enclose a note with a description of the problem
and the application.
1.7 Notes on safety conventions and icons
1.7.1 Warnings
!DANGER
Causes (/consequences)
Consequences of non-compliance (if applicable)
‣Corrective action
‣This symbol alerts you to a dangerous situation. Failure to avoid the situation will result in
a fatal or serious injury.
!WARNING
Causes (/consequences)
Consequences of non-compliance (if applicable)
‣Corrective action
‣This symbol alerts you to a dangerous situation. Failure to avoid the situation can result in
a fatal or serious injury.
Safety instructions CM14
6 Endress+Hauser
!CAUTION
Causes (/consequences)
Consequences of non-compliance (if applicable)
‣Corrective action
‣This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or more serious injuries.
NOTICE
Causes (/consequences)
Consequences of non-compliance (if applicable)
‣Corrective action
‣This symbol alerts you to situations which may result in damage to property.
1.7.2 Document symbols
Permitted
Indicates procedures, processes or actions that are permitted.
Preferred
Indicates procedures, processes or actions that are preferred.
Forbidden
Indicates procedures, processes or actions that are forbidden.
Additional information, tips
Reference to documentation
Reference to a page in this manual
Reference to a graphic
CM14 Identification
Endress+Hauser 7
2 Identification
2.1 Device designation
2.1.1 Nameplate
Compare the nameplate with the following diagram:
-10°C (14°F) < Ta < 60°C (140°F)
4
5
1
3
2
6
â 1
Liquiline
A0015221
1 Nameplate of the transmitter (example)
1 Device designation
2 Order code, serial number and ID number of the device
3 Power supply
4 Power consumption
5 Output values
6 Temperature range
2.2 Scope of delivery
The scope of delivery of the transmitter comprises:
• Transmitter for panel mounting
• Operating Instructions
• Fastening fixtures
Identification CM14
8 Endress+Hauser
2.3 Certificates and approvals
CE mark, Declaration of Conformity
The process display unit is designed to meet state-of-the-art safety requirements, has been
tested, and left the factory in a condition in which it is safe to operate. The device complies
with the applicable standards and regulations in accordance with EN 61 010-1 "Safety
requirements for electrical equipment for measurement, control and laboratory use".
The device described in these Operating Instructions therefore complies with the statutory
requirements of the EU Directives. The manufacturer confirms that the device has been
successfully tested by applying the CE mark.
An overview of all the certificates and approvals available is provided in the "Technical data"
section.
CM14 Installation
Endress+Hauser 9
3 Installation
3.1 Incoming acceptance, transport, storage
The permitted ambient and storage conditions must be observed. The precise specifications
can be found in Section "Technical data" (→ 32).
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Are the packaging or contents damaged?
• Is anything missing from the delivery? Compare the scope of delivery with the information
you specified in the order.
3.1.2 Transportation and storage
Note the following points:
• Pack the device so that is protected against impact for storage and transportation. The
original packaging provides optimum protection.
• The permitted storage temperature range is –40 to +85 °C (–40 to +185 °F); it is possible to
store the device in the borderline temperature ranges for a limited period (maximum 48
hours).
3.2 Installation
NOTICE
Overheating due to heat accumulation in the device
‣To avoid heat accumulation, please always make sure the device is sufficiently cooled.
If the device is operated in the upper temperature limit range, this reduces the operating
life of the display.
The transmitter is designed to be used in a panel.
The orientation is determined by the readability of the display. Connections and outputs are
fitted on the rear of the device. The wires are connected by means of number-coded terminals.
Ambient temperature range:–10 to +60 °C (14 to 140 °F)
3.3 Dimensions
Observe the installation depth of 150 mm (5.91 ") for the device incl. terminals and fastening
clips.
More dimensions can be found in Section "Technical data" (→ 32).
• Panel cutout: 92 mm x 45 mm (3.62 in x 1.77 in).
• Panel thickness: max. 26 mm (1 in).
• Max. viewing angle range: 45° to the left and right from the central display axis.
• If the devices are arranged horizontally beside one another in the X-direction, or arranged
vertically on top of one another in the Y-direction, the mechanical distance (specified by the
housing and front section) must be observed.
Installation CM14
10 Endress+Hauser
3.4 Installation procedure
The required panel cutout is 92 mm x 45 mm (3.62 in x 1.77 in).
A0015216
2 Installation in the panel
1. Screw the threaded rods (item 2) into the positions provided on the mounting frame
(item 1). Four opposing screw positions (item 3/4) are available for this purpose.
2. Push the device with the sealing ring through the panel cutout from the front.
3. To secure the tube in the panel, hold the device in a horizontal position and push the
installation frame (item 1), with the threaded rods screwed in, over the tube until the
frame locks into position.
4. Tighten the threaded rods to fasten the device in place.
To disassemble the device, the mounting frame can be unlocked at the locking elements (item
5) and then removed.
3.5 Post-installation check
• Is the sealing ring undamaged?
• Is the mounting frame securely engaged on the housing of the device?
• Are the threaded rods tightened?
• Is the device positioned in the center of the panel cutout?
Otros manuales para CM14
5
Tabla de contenidos
Otros manuales de Transmisor de Endress+Hauser
Endress+Hauser
Endress+Hauser iTEMP TMT85 Manual de usuario
Endress+Hauser
Endress+Hauser Omnigrad TMT146 Manual de usuario
Endress+Hauser
Endress+Hauser Liquisys M CLM 223 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT112 Manual de usuario
Endress+Hauser
Endress+Hauser cerabar M PMP 46 Manual
Endress+Hauser
Endress+Hauser RMA 422 Manual de usuario
Endress+Hauser
Endress+Hauser Nivotester FTR525 Manual de usuario
Endress+Hauser
Endress+Hauser Heat Especificaciones técnicas
Endress+Hauser
Endress+Hauser iTEMP PCP TMT181 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT85 Especificaciones técnicas
Endress+Hauser
Endress+Hauser AT5000 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT82 Manual de usuario
Endress+Hauser
Endress+Hauser Memograph CVM40 Especificaciones técnicas
Endress+Hauser
Endress+Hauser deltabar S PMD 25 K Manual de usuario
Endress+Hauser
Endress+Hauser Cerabar M PMP51 Manual de usuario
Endress+Hauser
Endress+Hauser RMA42 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Flowmeter Proline 200 Especificaciones técnicas
Endress+Hauser
Endress+Hauser iTEMP TMT84 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT162 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Liquiline M CM42 Instrucciones de uso
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
