Emotion Tech MDelta Manual de usuario

Version 1.2

Introduction - Printed parts 2

Introduction

Designers :

Hugo Flye hugo@emotion-tech.com

Thomas Batigne Thomas@emotion-tech.com

Antony Soury Antony@emotion-tech.com

Photographic credits :

Pictures and 3D representations made by

eMotion Tech http://www.emotion-tech.com

Picture director: Antony Soury

Authors:

eMotion Tech –http://www.Reprap-France.com

Loïc Déchaseaux [email protected]m

Antony Soury Antony@emotion-tech.com

Hugo Flye hugo@emotion-tech.com

Thomas Batigne Thomas@emotion-tech.com

Sources :

http://reprap.org/wiki/RepRap

http://www.repetier.com/

License :

µDelta: CC BY-NC-SA 4.0

This document: CC BY-NC-SA 4.0

http://creativecommons.org/licenses/by-nc-sa/4.0/

Update:

Last update : 25/07/2014

Links:

Reprap community: http://reprap.org/wiki/RepRap

Repetier-Host: http://www.repetier.com/

3D models database: http://www.thingiverse.com/

- Printed parts 3

Introduction........................................................................................................................................................2

µDelta introduction ............................................................................................................................................5

Safety instructions..............................................................................................................................................7

Assembly.............................................................................................................................................................8

Bill of materials...................................................................................................................................................9

A. Printed parts ..........................................................................................................................................9

B. Acrylic parts ...........................................................................................................................................9

1. Tensioner.................................................................................................................................... 9

2. Slider........................................................................................................................................... 9

3. Motor holder .............................................................................................................................. 9

4. Extruder...................................................................................................................................... 9

C. Smooth rods and connecting rods.......................................................................................................10

D. Mechanical parts .................................................................................................................................10

A. Screws, nuts and washers....................................................................................................................10

B. Electronics............................................................................................................................................11

C. Additional parts ...................................................................................................................................11

D. Hexagon kit ..........................................................................................................................................13

A. Options ................................................................................................................................................13

Tools .................................................................................................................................................................14

Mechanical assembly .......................................................................................................................................15

A. Bottom assembly .................................................................................................................................15

1. Inferior frame ........................................................................................................................... 15

2. Tensioner.................................................................................................................................. 16

3. Sliders ....................................................................................................................................... 21

B. Top assembly .......................................................................................................................................24

1. Motor holder assembly ............................................................................................................ 24

2. Superior frame fixation ............................................................................................................ 32

3. Extruder assembly .................................................................................................................... 34

C. Belt positioning....................................................................................................................................37

Core41

A. Core assembly......................................................................................................................................41

B. LED (optional) ......................................................................................................................................49

C. Connecting rods positioning................................................................................................................50

Finishing............................................................................................................................................................52

Electronics assembly ........................................................................................................................................57

A. Teensylu...............................................................................................................................................57

B. Connections .........................................................................................................................................58

4. Stepsticks.................................................................................................................................. 59

- Printed parts 4

5. Endstops ................................................................................................................................... 60

6. Motors...................................................................................................................................... 61

7. Cartridge heater. ...................................................................................................................... 62

8. Thermistor................................................................................................................................ 62

9. Fans .......................................................................................................................................... 62

10.USB and power supply.............................................................................................................. 63

Annex 1: Spool holder ......................................................................................................................................64

A. Assembly..............................................................................................................................................64

B. Connections .........................................................................................................................................66

µDelta introduction - Printed parts 5

µDelta introduction

µDelta is developed by eMotion Tech. This new 3D printer is easy to assemble and to operate without loss of

performances.

Data sheet:

DATAS

Printing surface Ø110 x 190mm

Layer height [0,1 - 0,35]

Electronic type Teensylu + 4 Stepsticks (integrated firmware)

Motors NEMA 17

Belt Type GT2

Extrusion Head Hexagon 0.4

Dimensions : Height 440mm Width 250mm Depth 250mm

Nominal printing speed 70mm/s

Max speed 200mm/s

Nominal speed 130mm/s

Average precision 100 microns

Average precision (Z) 50 microns

Operating system Windows™ XP, Windows™ Vista, Windows™ 7+, Ubuntu 12+

Consumable PLA 1.75mm

Provided with Repetier preset for µDelta

Connectivity USB

Power supply provided yes, 12V 120W

STRUCTURE

Laser cut Acrylic 5mm

Extruder core printed in ABS with 0.2mm layer height

Smooth rod 8mm

Manufactured Plate plywood 12mm

µDelta introduction - Printed parts 6

ERGONOMY

Easy to mount: A 3D printer kit with an intuitive assembly

Simple electronic, no soldering

Easy wiring and assembly

Belt adjustment with ergonomic belt tensioners

Easy to calibrate: A simplified software

Fully software calibration

Pre-configured open-source software (no firmware upload required, Repetier Host and Slic3r pre-

configured)

Easy to maintain

Quick height adjustment with the software

OPTIMISATION AND UPGRADE

You can improve the µDelta by adding the following option (soon available on eMotion Tech website):

Spool holder with fan

LCD screen controller to print without computer

Lighting with circular LED

Heated bed

Safety instructions - Printed parts 7

Safety instructions

General safety instructions

ALWAYS HAVE ADULT SUPERVISON WHEN USING THE PRINTER.

The nozzle can reach 270°C, TO AVOID BURNING, DO NOT TOUCH THE NOZZLE WHILE THE PRINTER IS

WORKING.

KEEP THE PRINTER AWAY FROM CHILDREN AND ANIMALS.

OPERATE IN A VENTILATED ROOM. Plastic fumes effects are not known. In case of use in a closed room we

recommend the use of an extractor fan.

The addition of protections is your responsibility. Safety can be improved by:

An emergency stop button

Housing protection

Smoke detector

CE marking

µDelta is a 3D printer kit. It includes all the parts you need for assembling but does not include additional

protections.

Electrical safety.

The power supply provided is labelled CE. The Power supply is protected against short-circuit and do not need

any modifications. The µDelta operate at voltage of 12V and is not concerned by the low voltage directive.

Further information

Information above are not exhaustive.

We used sources of information we consider as reliable. However, we cannot guarantee that all these

information are true and complete.

We assume no liability for loses, injuries or damages due to assembly, transporting, storage, use, assembly,

transporting or removal of the product.

- Printed parts 8

Assembly

Bill of materials - Printed parts 9

Bill of materials

A. Printed parts

1x Core

12x rod clamp

1x filament guide

B. Acrylic parts

Acrylic parts can be covered with protection and it may remain pieces of plastic. Remove it before use

We provide additional parts.

1. Tensioner

2. Slider

6x eM 1

6x eM 2

6x eM 3

6x eM 4

6x eM 5

3. Motor holder

4. Extruder

3x eM 7

6x eM 6

2x eM 8

1x eM 9

1x eM 10

2x eM 11

1x eM 12

1x eM 13

Bill of materials - Smooth rods and connecting rods 10

C. Smooth rods and

connecting rods

D. Mechanical parts

6x Ø8x400mm smooth rod

9x Linear bearing

1x Spring

6x Connecting rod

3x 624 ball bearing

1x 604 ball bearing

1x drive wheel

3x GT2 Belt

3x GT2 Pulley

A. Screws, nuts and washers

6x M3x10mm screw

14x M3x20mm screw

20x M3x25mm screw

15x M3x30mm screw

11x M3x50mm screw

1x M4x50mm screw

4x M4x25mm screw

6x M2.5x16mm screw

3x Wood screw

60xM3 nut

4x M3 wing nut

8x M4 nut

6x M2.5 nut

76x Ø3mm washer

8x Ø4mm small washer

4x Ø4mm big washer

1x M4 Nylstop nut

8x M3 grub screw

Tabla de contenidos

Otros manuales de Impresora 3D de Emotion Tech

Emotion Tech

Emotion Tech MicroDelta Rework Manual de usuario

Emotion Tech

Emotion Tech MicroDelta Rework Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

Emotion Tech mDelta Manual de usuario

Manuales populares de Impresora 3D de otras marcas