Emerson Rosemount ET210 Manual de usuario
Quick Start Guide
00825-0100-4211, Rev AA
June 2019
Rosemount™ ET210 Wireless Corrosion
Transmitter
NOTICE
This guide provides basic guidelines for Rosemount Wireless Corrosion Transmitter. It does not provide
instructions for configuration, diagnostics, maintenance, service, troubleshooting or intrinsically safe
(I.S.) installations. Refer to the Rosemount Wireless Corrosion Transmitter Reference Manual for more
instruction. The manual and this guide are also available electronically on EmersonProcess.com
\Rosemount.
Shipping considerations
Each device contains two “D” size primary lithium-thionyl chloride battery cells. Primary lithium
batteries are regulated in transportation by the U.S. Department of Transportation, and are also
covered by IATA (International Air Transport Association), ICAO (International Civil Aviation
Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the responsibility
of the shipper to ensure compliance with these or any other local requirements. Consult current
regulations and requirements before shipping.
WARNING
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review the approvals
section of this manual for any restrictions associated with a safe installation.
Before connecting a CC21 in an explosive atmosphere, make sure the instruments in the segment
are installed in accordance with intrinsically safe or non-incendive field wiring practices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired
operation.
This device must be installed to ensure a minimum antenna separation distance of 20 cm (8 in.)
from all persons.
The power module may be replaced in a hazardous area. The power module has surface
resistivity greater than one gigaohm and must be properly installed on the wireless device.
Care must be taken during transportation to and from the point of installation to prevent a
potential electrostatic charging hazard.
Polymer enclosure has surface resistivity greater than one gigaohm. Care must be taken
during transportation to and from the point of installation to prevent a potential electrostatic
charging hazard.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of
end users’ equipment. This could be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your
system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true
for all systems used within the facility.
Quick Start Guide June 2019
2 Emerson.com/RosemountEmerson.com/Rosemount
Contents
Overview......................................................................................................................................5
Wireless considerations................................................................................................................7
Field communicator connections................................................................................................. 8
Physical installation...................................................................................................................... 9
Commissioning device............................................................................................................... 12
Product certifications................................................................................................................. 15
June 2019 Quick Start Guide
Quick Start Guide 3
Quick Start Guide June 2019
4 Emerson.com/RosemountEmerson.com/Rosemount
1 Overview
Figure 1-1: Rosemount ET210 Wireless Corrosion Transmitter
A. Antenna
B. Power module
C. Head
D. Lanyard hole
E. Strap slot
F. Foot
G. Cap
H. Shoe
June 2019 Quick Start Guide
Quick Start Guide 5
1.1 Required equipment - IK220
1.2 Required tooling
Tooling is supplied in the Permasense IK220 Installation Kit:
•Hex key, 2.5mm, for power module retaining bolts
•Strap tightening tool - HCL SM-FT-2000
1.3 What's in the box
•Permasense ET210 sensor, complete with protective cap
•Lanyard kit, 316 stainless steel lanyard 6.5ft. (2m) in length, Gripple
No.2, release key
•Silicone rubber shoe
•Strap kit, comprising polymer strap and buckle
•Permasense BP20E power module
•M3 x 16mm stainless steel retaining bolts, two per sensor
Quick Start Guide June 2019
6 Emerson.com/RosemountEmerson.com/Rosemount
2 Wireless considerations
Power up sequence
The Emerson Smart Wireless Gateway should be installed and functioning
properly before any wireless devices are powered. Commission the
Rosemount ET210 and install the BP20E power module to power the device
only (following instructions below) after the gateway has been installed and
functioning. This results in a simpler and faster network installation.
Enabling active advertising on the Gateway ensures new devices are able to
join the network faster. For more information see the Smart Wireless
Gateway Manual (document number 00809-0200-4420).
Antenna position
The antenna is internal to the ET210 transmitter. The antenna should also be
approximately 3 ft. (1 m) from any large structure, building, or conductive
surface to allow for clear communication to other devices.
June 2019 Quick Start Guide
Quick Start Guide 7
3 Field communicator connections
The CC21 commissioning cable is connected and removed from the
transmitter in the same way as BP20E power module. The USB connector is
plugged in to the tablet PC as shown in Figure 3-1.
Figure 3-1: IK220 Commissioning Kit
A. Tablet PC
B. CC21
C. USB cable plugged into USB port
D. WT210/ET210 sensor
Quick Start Guide June 2019
8 Emerson.com/RosemountEmerson.com/Rosemount
4 Physical installation
4.1 Mounting the sensor
Procedure
1. Identify the location where the sensor should be fixed. Clean the area
where the sensor will touch the pipe, mainly to remove any particles
which might keep the transducer away from the pipe surface or
damage the face of the transducer. Use a permanent marker to show
exactly where each sensor is to be placed.
2. Remove the protective cap from the sensor. Ensure tools and
fastenings are kept away from the sensor when the cap is removed.
Ensure the metal ring and the rubber shoe are fitted before installing
the sensor. If either part is missing, do not proceed with the
installation.
3. Place the sensor in the required location on the pipe.
Note
The magnets used in the sensors have a high pull force. To avoid
damage, and to get the precise location for each sensor, put the
sensor at an angle to the pipe and then gently lower the shoe onto
the pipe.
4. Cut the strap to a suitable length. This will depend on the diameter of
the pipe. If the diameter of the pipe is D cm / inches, the length can
be approximated by 3 x (D + 10) cm (or 3 x (D + 4) inches).
June 2019 Quick Start Guide
Quick Start Guide 9
5. Attach a buckle to one end of the strap. Ensure the strap teeth are on
the outside of the strap, and are fully engaged with the buckle.
Note
A small flat screwdriver can be used to disengage the buckle, if
required.
6. Slide the strap through the sensor(s), pass the strap through the
buckle. Where possible position the buckle opposite the middle
sensor to ensure both sides of the strap are tightened evenly.
7. Tighten the strap by hand to gently hold the sensor in place. If
necessary, adjust the position of the sensor to ensure correct
alignment around the circumference of the pipe. With multiple
sensors on a strap, there should be a gap between the shoes of
adjacent sensors.
8. Prepare the lanyard kit and decide how it will be positioned. Wrap the
lanyard around the circumference of the pipe. The 7 ft. (2m) length
will accommodate a maximum diameter of 24 in. When it is not
possible to wrap the lanyard around a pipe, find an alternative
attachment point for the lanyard.
9. Thread the bare end of the wire through the loop in the lanyard to
secure it to the pipe.
10. Feed the bare end of the lanyard into the ‘gripple’ and push the
‘gripple’ 6 in. (15 cm) up from the bare end.
Quick Start Guide June 2019
10 Emerson.com/RosemountEmerson.com/Rosemount
Tabla de contenidos
Otros manuales de Transmisor de Emerson
Emerson
Emerson Rosemount 644 with HART Protocol Manual de usuario
Emerson
Emerson Rosemount 644 HART Manual de usuario
Emerson
Emerson Rosemount 8750W Manual de usuario
Emerson
Emerson Micro Motion 4200 Manual de usuario
Emerson
Emerson Rosemount 5400 Series Manual de usuario
Emerson
Emerson Rosemount 3051S Series Manual de usuario
Emerson
Emerson MAS 2600 Manual de usuario
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Rosemount TCL Manual de usuario
Emerson
Emerson Rosemount FCL-01 Manual de usuario
Emerson
Emerson Micro Motion 800 Manual de usuario
Emerson
Emerson Rosemount 1208C Manual de usuario
Emerson
Emerson Rosemount 2051HT Manual de usuario
Emerson
Emerson Rosemount 3408 Manual de usuario
Emerson
Emerson Rosemount MultiVariable 3051SMV Manual de usuario
Emerson
Emerson Micro Motion 4200 Manual de usuario
Emerson
Emerson Rosemount 5400 Series Manual de usuario
Emerson
Emerson Rosemount FCL-01 Manual de usuario
Emerson
Emerson Rosemount 3051 Manual de usuario
Emerson
Emerson Rosemount 5400 Series Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
