Emerson Rosemount 3144P Manual de usuario

Quick Start Guide

00825-0100-4021, Rev PB

March 2021

Rosemount™ 3144P Temperature

Transmitter

with HART® Protocol and Rosemount

X-well™ Technology

Contents

About this guide...........................................................................................................................3

System readiness......................................................................................................................... 5

Verify configuration..................................................................................................................... 6

Set the switches......................................................................................................................... 10

Mount the transmitter................................................................................................................11

Wire and apply power................................................................................................................ 13

Perform a loop test.....................................................................................................................18

Safety Instrumented Systems (SIS).............................................................................................19

Product certifications................................................................................................................. 20

Quick Start Guide March 2021

2 Rosemount 3144P

1 About this guide

This guide provides basic guidelines for installing the Rosemount 3144P

Transmitter. It does not provide instructions for detailed configuration,

diagnostics, maintenance, service, troubleshooting, Explosion-proof,

Flameproof, or intrinsically safe (I.S.) installations. Refer to the Rosemount

3144P Transmitter Reference Manual for more instructions. The manual and

this guide are also available electronically on Emerson.com/Rosemount.

WARNING

Explosions

Explosions could result in death or serious injury.

Installation of device in an explosive environment must be in accordance

with appropriate local, national, and international standards, codes, and

practices.

Review the Product Certifications section of this document for any

restrictions associated with a safe installation.

Process leaks

Process leaks may cause harm or result in death.

Install and tighten thermowells and sensors before applying pressure.

Do not remove the thermowell while in operation.

Conduit/cable entries

The conduit/cable entries in the transmitter housing use a ½–14 NPT

thread form.

When installing in a hazardous location, use only appropriately listed or

Ex certified plugs, glands, or adapters in cable/conduit entries.

Electrical shock

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be

present on leads could cause electrical shock.

March 2021 Quick Start Guide

Quick Start Guide 3

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or

misconfiguration of end users’ equipment. This could be intentional or

unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for all

systems used within the facility.

Quick Start Guide March 2021

4 Rosemount 3144P

2 System readiness

2.1 Confirm HART revision capability

If using HART based control or asset management systems, confirm the

HART capability of those systems prior to transmitter installation. Not all

systems are capable of communicating with HART Revision 7 Protocol. You

can configure the transmitter for either HART Revision 5 or 7.

For instructions on how to change the HART revision of your transmitter,

refer to Switch HART revision mode.

March 2021 Quick Start Guide

Quick Start Guide 5

3 Verify configuration

The Rosemount 3144P Transmitter communicates using a Field

Communicator (communication requires a loop resistance between 250 and

1100 ohms) or AMS Device Manager.

Do not operate when power is below 12 Vdc at the transmitter terminal.

Refer to the Rosemount 3144P Transmitter Reference Manual and Field

Communicator Reference Manual.

3.1 Update the Field Communicator software

To fully communicate with the Rosemount 3144P Transmitter, you need the

latest Field Communicator Field Device Revision Dev v5 or v7, DD v1 or

greater. Transmitters equipped with Rosemount X-well Technology require

DD revision 3144P Dev. 7 Rev. 1 or greater to view this functionality.

The Device Descriptors are available with new communicators at

Emerson.com/Rosemount, or you can download them into existing

communicators at any Emerson Service Center.

The device descriptors are as follows:

•Device in HART 5 mode: Device v5 DDv1

•Device in HART 7 mode: Device v7 DDv1

Complete the following steps to determine if you need to upgrade your

device. Refer to Figure 3-1.

Quick Start Guide March 2021

6 Rosemount 3144P

Figure 3-1: Connecting a Communicator to a Bench Loop

A. Power/signal terminals

B. 250 Ω ≤ RL ≤ 1100 Ω

C. Power supply

Procedure

1. Connect the sensor.

See the wiring diagram located on the inside of the housing cover.

2. Connect the bench power supply to the power terminals ("+" or "-").

3. Connect a Field Communicator to the loop across a loop resistor or at

the power/signal terminals on the transmitter.

The following message will appear if the communicator has a previous

version of the device descriptors (DDs):

NOTICE: Upgrade the communicator software to access new XMTR functions.

Continue with old description?

Note

If this notice does not appear, the latest DD is installed.

If the latest version is not available, the communicator will communicate

properly, but when the transmitter is configured some new capabilities may

not be visible.

To prevent this from happening, upgrade to the latest DD or answer NO to

the question and default to the generic transmitter functionality.

March 2021 Quick Start Guide

Quick Start Guide 7

3.2 Switch HART revision mode

If the HART Protocol configuration tool is not capable of communicating

with HART Revision 7, the transmitter will load a generic menu with limited

capability. The following procedure will switch the HART Revision mode

from the generic menu.

Procedure

Select Manual Setup → Device Information → Identification → Message.

a) To change to HART Revision 5, enter HART5 in the Message field.

b) To change to HART Revision 7, enter HART7 in the Message field.

Function HART 5 Fast Keys HART 7 Fast Keys

2-wire offset sensor 1 2, 2, 1, 5 2, 2, 1, 6

2-wire offset sensor 2 2, 2, 2, 5 2, 2, 2, 6

Alarm values 2, 2, 5, 6 2, 2, 5, 6

Analog calibration 3, 4, 5 3, 4, 5

Analog output 2, 2, 5 2, 2, 5

Average temperature setup 2, 2, 3, 3 2, 2, 3, 3

Burst mode N/A 2, 2, 8, 4

Comm status N/A 1, 2

Configure additional messages N/A 2, 2, 8, 7

Configure Hot Backup™2, 2, 4, 1, 3 2, 2, 4, 1, 3

Date 2, 2, 7, 1, 2 2, 2, 7, 1, 3

Descriptor 2, 2, 7, 1, 3 2, 2, 7, 1, 4

Device information 2, 2, 7, 1 2, 2, 7, 1

Differential temperature setup 2, 2, 3, 1 2, 2, 3, 1

Filter 50/60 Hz 2, 2, 7, 5, 1 2, 2, 7, 5, 1

Find device N/A 3, 4, 6, 2

First good temperature setup 2, 2, 3, 2 2, 2, 3, 2

Hardware revision 1, 8, 2, 3 1, 11, 2, 3

HART lock N/A 2, 2, 9, 2

Intermittent sensor detect 2, 2, 7, 5, 2 2, 2, 7, 5, 2

Lock status N/A 1, 11, 3, 7

Long tag N/A 2, 2, 7, 2

Quick Start Guide March 2021

8 Rosemount 3144P

Function HART 5 Fast Keys HART 7 Fast Keys

Loop test 3, 5, 1 3, 5, 1

LRV (lower range value) 2, 2, 5, 5, 3 2, 2, 5, 5, 3

Message 2, 2, 7, 1, 4 2, 2, 7, 1, 5

Open sensor holdoff 2, 2, 7, 4 2, 2, 7, 4

Percent range 2, 2, 5, 4 2, 2, 5, 4

Sensor 1 configuration 2, 2, 1 2, 2, 1

Sensor 1 serial number 2, 2, 1, 7 2, 2, 1, 8

Sensor 1 setup 2, 2, 1 2, 2, 2

Sensor 1 status N/A 2, 2, 1, 2

Sensor 1 type 2, 2, 1, 2 2, 2, 1, 3

Sensor 1 unit 2, 2, 1, 4 2, 2, 1, 5

Sensor 2 configuration 2, 2, 2 2, 2, 2

Sensor 2 serial number 2, 2, 2, 7 2, 2, 2, 8

Sensor 2 setup 2, 2, 2 2, 2, 2

Sensor 2 status N/A 2, 2, 2, 2

Sensor 2 type 2, 2, 2, 2 2, 2, 2, 3

Sensor 2 unit 2, 2, 2, 4 2, 2, 2, 5

Sensor drift alert 2, 2, 4, 2 2, 2, 4, 2

Simulate device variables N/A 3, 5, 2

Software revision 1, 8, 2, 4 1, 11, 2, 4

Tag 2, 2, 7, 1, 1 2, 2, 7, 1, 1

Terminal temperature units 2, 2, 7, 3 2, 2, 7, 3

URV (upper range value) 2, 2, 7, 3 2, 2, 7, 3

Variable mapping 2, 2, 8, 5 2, 2, 8, 5

Thermocouple diagnostic 2, 1, 7, 1 2, 1, 7, 2

Min/max tracking 2, 1, 7, 2 2, 1, 7, 2

Rosemount X-well configuration N/A 2, 2, 1, 11

March 2021 Quick Start Guide

Quick Start Guide 9

4 Set the switches

The Rosemount 3144P Transmitter comes with hardware switches to

configure alarms and lock the device. Use the following procedures to set

the switches.

WARNING

Enclosure

Enclosure covers must be fully engaged to meet explosion-proof

requirements.

4.1 Set the switches with an LCD display

Procedure

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Unscrew the LCD display screws and gently slide the meter straight

off.

4. Set the alarm and security switches to the desired position.

5. Gently slide the LCD display back into place.

6. Replace and tighten the LCD display screws to secure the LCD

display.

7. Reattach housing cover.

8. Apply power and set the loop to automatic control.

4.2 Set the switches without an LCD display

Procedure

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Set the alarm and security switches to the desired position.

4. Reattach housing cover.

5. Apply power and set the loop to automatic control.

Quick Start Guide March 2021

10 Rosemount 3144P

Otros manuales para Rosemount 3144P

Tabla de contenidos

Otros manuales de Transmisor de Emerson

Emerson

Emerson Rosemount ET310 Manual de usuario

Emerson

Emerson Rosemount FCL-01 Manual de usuario

Emerson

Emerson Rosemount 702 Manual de usuario

Emerson

Emerson Rosemount 3051S Series Manual de usuario

Emerson

Emerson Rosemount5081 Manual de usuario

Emerson

Emerson Rosemount 848T Manual de usuario

Emerson

Emerson Rosemount 848T Manual de usuario

Emerson

Emerson Rosemount MultiVariable 3051SMV Manual de usuario

Emerson

Emerson Rosemount 705 Manual de usuario

Emerson

Emerson Rosemount 2051 Wireless Series Manual de usuario

Emerson

Emerson Rosemount 2051 Manual de usuario

Emerson

Emerson Rosemount 4088B MultiVariable Manual de usuario

Emerson

Emerson Rosemount 56 Manual de usuario

Emerson

Emerson Rosemount 8712C Guía de configuración

Emerson

Emerson Rosemount 2240S Manual de usuario

Emerson

Emerson CSI 9420 Manual de usuario

Emerson

Emerson Rosemount X-STREAM O2 Transmitter Manual de usuario

Emerson

Emerson Rosemount 708 Manual de usuario

Emerson

Emerson Rosemount MCL-220 Manual de usuario

Emerson

Emerson Rosemount 8750W Manual de usuario

Emerson

Emerson Rosemount 3095 Manual de usuario

Emerson

Emerson Rosemount MultiVariable 4088A Manual de usuario

Emerson

Emerson Rosemount 848T Manual de usuario

Emerson

Emerson Rosemount ET310C Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario