Elite Screens Elite Home 2 Series Manual de usuario

Rev.060616-DR www.elitescreens.com

Electric Motorized Projection Screen

Home 2 Series

User’s Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedure below.

Caution: The Screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop

in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or

modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your

warranty. For more information, please contact our Technical Support Department at techsupport@elitescreens.com.

Please retain this user’s guide for future reference.

To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

Handle the unit carefully during transportation to avoid any damages.

To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

The power outlet supplying power to the unit should be close to the unit and easily accessible.

Do not install the unit on uneven or inclined surfaces.

Do not place any heavy objects over the power cord.

Position the power cord properly to avoid creating a trip obstacle.

To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the power

cord.

The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble

this unit by yourself. No one except authorized technicians can open and make repairs to this unit.

Make sure the power source that this unit is connected to has a continuous power flow.

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid over heat.

Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.

Avoid direct sun light, rain shower and moisture.

Keep away from fire sources and high temperature to prevent this device from overheating.

Cut off the power supply first before transportation or maintenance.

To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious

damage or if there are any evident broken parts.

Rev.060616-DR www.elitescreens.com

WARNING

Due to various installation environments, the instructions provided in this user’s guide are for reference

only. Please consult a professional installation company for further installation and safety advice. The

installer must insure that proper mounting hardware is used to provide adequate strength suitable for the

installation. Elite Screens is not liable for any faulty installations.

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures.

Reorient or relocate the receiving antenna of the device which may be casing the interference.

Increase the separation between the screen and the device’s receiver.

Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles

such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the

viewing surface will not cause the casing to become loose or fall. The installer must insure that the fasteners used

are of adequate strength and suitable for the installation location.

Rev.060616-DR www.elitescreens.com

Sensor

3-way Wall box switch

Sensor

Home 2 Series | Controls and Accessories

A. IR Remote

B. RF Remote

C. Wall switch control box

D. 5-12 volt trigger cable

E. IR extended “eye” receiver

F. Wireless 5-12v (3.5 mm)

mono trigger cable

G. AAA batteries

H. Bubble leveler

Screen Operation

Electric Current: Depending upon region, your Elite Screen will operate on 100v, 110v, or 220v voltage.

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.

6 ways to control your Home 2

1. IR remote control (Item A, Fig 1): The Infrared functions by direct line

of sight contact with a beam range of 30 feet. Aim the IR remote at the

circular window located on the left side of the screen.

2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs

directly into the control box’s RJ45 port to present a low profile line-of-

sight control option for your IR remote control even in a recessed ceiling

installation.

3. RF Remote Control (Item B): The radio waves eliminate the need for a

direct line of sight with a range of 100 feet.

4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall

mount switch with an up/stop/down button and plugs directly into the

control box’s RJ45 port.

Fig.3

STOP

DOWN

Fig.1

IR/RF remote

IR “eye” receiver

Fig.2

Rev.060616-DR www.elitescreens.com

6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a

handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency technology

can be programmed to send a wireless signal to synchronize its drop/rise with the projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions

Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector

Step 3: Make sure to unplug your screen from the power outlet

Step 4: Hold the UP button on your RF remote

Step 5: While holding the UP button, plug the screen back to the power outlet

Step 6: Wait 5 seconds and then release the UP button

Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to

control your screen with your projector’s power cycle

Repeat the steps again if not successful.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30seconds

for full off and on cycle each time)

Hardware Parts List

Please make sure all items listed below are included before proceeding with the installation.

Hardware Parts List

QTY

A. Screw & Dry Wall Anchor

2 EA.

B. Bolt

2 EA.

C. Masonry Screw & Anchor

2 EA.

D. Extruded Hanging Bracket

2 or

3 EA.

120” & above x 3 brackets

DC 5-12V out

The back of the

projector

Wireless 5-12V trigger cable

Stop

Down

Fig 5

5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V

trigger input allows your screen to synchronize its drop &

rise with the projector’s power cycle. The screen deploys

when the projector powers up and will retract when the

projector powers down. The 5-12 volt RJ45 cable connects

to your projector’s trigger output via a separate cable that

may or may not be provided by the manufacturer of the

projector. The trigger feature will not work without an

output cable from the projector, but it can be tested by

connecting the Red (+) and Green (-) cable to a 9-volt

battery.

Fig.4

3-prong power cable

Red: DC 12 +

Green: 0 V -

RJ-45 input connection for

5/12 volt trigger inside of case

Rev.060616-DR www.elitescreens.com

Installation Instructions

Please consult a professional installer. Elite Screens is not liable for any faulty installations.

1. Insert each Bolt (B) through the right & left slide channel located on the top of the screen’s case.

2. Slide the Extruded Hanging Bracket (D) through the rail located below the slide channel until it meets with

the top of the Bolt (B) and slightly secure the lug-nuts located on the top & bottom of the bolt to attach the

bracket.

3. Mark the installation location to drill your hole. Insert the proper screw and secure the bolts to the bracket.

4. Example of the Home 2 installed to a wall, ceiling and enclosed.

Top hole for ceiling installation

Back hole for wall installation

Flush mount

to wall

Flush mount

to ceiling

Enclosed

installation

*Allow 2” of spacing

between the front and

back of the screen casing.

Rev.060616-DR www.elitescreens.com

Trouble Shooting

For additional information, please contact Elite Screens at techsupport@elitescreens.com

1. If your screen does not move, please check the power supply. The screen will understandably not move

without power.

2. Make sure the power cord is firmly plugged to the power outlet.

3. Make sure that all cable connections are secure.

4. If the screen works well with the line switch but not with the remote control, please make sure the remote

controls have fresh batteries. Change the batteries every 6 months to ensure proper operation of the

remotes.

FAQ’s

1. Q: Why does my screen no longer function?

A: Make sure your wall plug has power and that the screen is properly plugged. The fuse on the screen will

also need to be checked. Please contact techsupport@elitescreens.com for the location. The tubular motor

in this screen is equipped with a thermal relay. This feature will automatically shut off the screen in the

event of the motor becoming too hot. This will prevent the motor from overheating. If you should

experience this, please let the screen’s temperature decrease for 10-15 min. before usage.

2. Q: How is the screen material cleaned?

A: The screen material can be cleaned with mild soap and water.

3. Q: What type of batteries do the remote controls require?

A: The IR and RF remote controls use AAA alkaline batteries.

4. Q: Can you manually pull down the screen?

A: No, manually pulling down the screen will damage the electronic motor rolling system and void your

warranty.

5. Q: How could I setup my Screens IR receiver to work with my learning remote control system

Do you have any IR codes I can use to achieve this?

A: Our IR remote controls have been evaluated and entered in to the databases of some Universal remote

control manufacturers. Please contact the manufacturer of your remote to inquire about your remotes

ability to function with ours. If they have not evaluated our remote control then the following list of Binary

codes will be used for most remote setups.

For Spectrum, VMAX2 (Plus), Home2 and CineTension 2 Series

Up: 1111 0000 0001

Stop: 1111 0000 0010

Down: 1111 0000 0100

6. Q: What is the gain on the matte white screen material?

A: The matte white material has a gain of 1.1. For detailed information, please visit

www.elitescreens.com/home2

For local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Otros manuales para Elite Home 2 Series

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens DE103C82H Manual de usuario

Elite Screens

Elite Screens isf CineWhite UHD-B Sable Frame B2 Series Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Manual de usuario

Elite Screens

Elite Screens Elite Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens Lunette Series Manual de usuario

Elite Screens

Elite Screens QuickStand Series Manual de usuario

Elite Screens

Elite Screens Yard Master 2 Series Manual de usuario

Elite Screens

Elite Screens 100 series Manual de usuario

Elite Screens

Elite Screens SilverFrame 100GH1 Manual de usuario

Elite Screens

Elite Screens CineTension 3 Series Manual de usuario

Elite Screens

Elite Screens Pop-Up Cinema Series Manual de usuario

Elite Screens

Elite Screens F100XWH1 Manual de usuario

Elite Screens

Elite Screens F100NWH Manual de usuario

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Guía

Elite Screens

Elite Screens Saker Series Manual de usuario

Elite Screens

Elite Screens TE200HR2 Manual de usuario

Elite Screens

Elite Screens Kestrel Home Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens Starling Series Manual de usuario

Elite Screens

Elite Screens Pro Frame Thin DarkUST Series Manual de usuario

Elite Screens

Elite Screens 2 CLR Series Manual de usuario

Elite Screens

Elite Screens ezCinema Series Manual de usuario

Elite Screens

Elite Screens Starling Tab-Tension 2 Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación