Elite Screens CineTension 3 Series Manual de usuario

Rev. V06142023DT (DS8621) 1 www.elitescreens.com

CineTension 3 Series

Tab-tensioned Electric Motorized Projection Screen

User’s Guide – E/H type (RC1)

V1.0

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top

Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or

modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void

your warranty. For more information, please contact our Technical Support Department.

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.

•The power outlet supplying power to the unit should be close to the unit and easily accessible.

•Do not install the unit on uneven, inclined surfaces;

•Do not install in damp places to avoid an electric shock or short circuit.

•Do not place any heavy objects over the power cord.

•Position the power cord properly to avoid creating a trip obstacle.

•To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the power cord.

•The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble this

unit by yourself. No one except authorized technicians can open and make repairs to this unit.

•Make sure the power source that this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid

over heat.

•Do not handle the power plug when your hands are wet or your feet are in contact with water.

•Properly dispose of this equipment according to the environmental regulations in your area when product is

no longer of service.

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.

•Avoid direct sun light, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from overheating.

•Cut off the power supply first before transportation or maintenance.

•To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious damage

or if there are any evident broken parts.

Rev. V06142023DT (DS8621) 2 www.elitescreens.com

Installation Warning

The instructions provided in this user’s guide are for reference only. Please consult a professional installation

company for further installation and safety advice.The installer must ensure that proper mounting hardware

is used to provide adequate strength suitable for the installation. Elite Screens is not liable for any faulty

installations.

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop in the

roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please

contact Elite Screens Customer Service for any questions.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this equipment

causes harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures.

✓Reorient or relocate the receiving antenna of the device which may be casing the interference.

✓Increase the separation between the screen and the device’s receiver.

✓Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles

such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the

viewing surface will not cause the casing to become loose or fall. The installer must ensure the fasteners that are

used are of adequate strength and suitable for the installation location.

Screen operation

Electric Current: 100 ~ 110v voltage

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen has power, you’ll be able to control it using any of the 5 methods described below.

CineTension 3 | Controls and Accessories

A. IR Remote

ZRC1-IR

B. RF Remote

ZRC1-RF

C. Wall box

controller

ZRC1-WB

D. RJ50 Cable

ZRC1-RJ50

E. AAA

batteries

F. Bubble Level

Rev. V06142023DT (DS8621) 3 www.elitescreens.com

5 Ways to control your screen

1. IR Remote control (Item A, Fig 1): The Infrared functions by direct line of

sight contact using an effective beam range of 25 feet within a 30-degree angle.

Aim the IR remote directly at either the IR receiver on the Wall Box Controller

or on the screen to operate the screen.

Note: Assure there is no obstruction between the IR remote and IR receiver.

2. RF Remote Control (Item B): The radio waves eliminate the need for a direct

line of sight and has a longer distance control range.

The RF remote is already pre-synced/paired and ready to use. If

synchronization/ pairing is needed, please follow the steps below.

How to synchronize/pair a new RF remote:

•Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-box LED

flashes). Reference the wall box controller section for programming key location.

•Then press the “Up Key” on the RF remote.

•The Wall box LED will flash 5 times, to indicate the RF remote has been properly synchronized/paired.

How to change the RF code (For use when multiple screens/RF remotes are owned)

Changing the RF code avoids controlling multiple screens at the same time and prevents electrical interference leading

to accidental control of the screen.

1. Remove the batteries

2. Change the RF code switch

3. Insert the batteries

4. Synchronize it with the wall box controller

3. Wall box controller (Item C, Fig 2): The wall box controller switch is a wall mounted control box with an

up/stop/down button. It plugs directly into the screen’s RJ50 port.

LED light

STOP

DOWN

Fig.1

IR/RF remote

IR Lens

(IR remote only)

Battery compartment

Default

“000”

RF Remote

BACK VIEW

Slide Switches

for RF Code

change

Wall box controller

IR Receiver

RJ50 cable

Wall box controller

SIDE VIEW

RJ50 PORT:

Connects to the

Screen RJ50 PORT

(RJ50 CABLE ONLY)

3.5mm mono Projector

Trigger Port (if Projector

equipped)

Wall box controller

BACK VIEW

Programming

Key

Fig.2

Rev. V06142023DT (DS8621) 4 www.elitescreens.com

4.Wired 5-12 volt trigger (Fig 3):Requires a 3.5mm to 3.5mm mono cable (not included)

Step 1: Connect one end of the RJ50 cable to the screen and the other end

to the Wall box controller.

Step 2: Then connect one end the 3.5mm mono cable to the wall box

controller and the other to the projector.

Once the two cables have been connected, the wired trigger feature is

ready to synchronize the screen’s up/down operation with the

projector’s power cycle.

•Projector on, screen drops

•Projector off, screen raises

5. Wireless 5-12 volt trigger (Fig 4): Requires a 3.5mm to 3.5mm mono cable (not included).

The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld remote control, or as

a Wireless 5-12 volt trigger. The radio frequency technology sends a wireless signal that synchronizes the screen’s

drop & rise with the projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigger

The 5-12V wireless trigger should already be synced and ready to work.

Step 1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm mono end of the cable to your projector

Step 3: Turn on the projector and the screen should automatically deploy.

Step 4: Turn off your projector and the screen should automatically retract.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30 seconds

for full off and on cycle each time)

Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box controller per the

instructions in the Radio Frequency remote section.

Mono 3.5mm

Projector Trigger

Port

Fig 4

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

STOP

DOWN

Projector

RF remote control

SIDE VIEW

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

Wall box controller

RJ50 cable

Fig. 3

Projector

Rev. V06142023DT (DS8621) 5 www.elitescreens.com

ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)

* Wall box controller must be connected to the screen.

1. Preset the Screen’s Drop Position:

Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it at.

Press & hold the “Programming Key”, then press the “Down key” on the Wall Box Controller. The LED will flash 5

times to confirm new programmed drop position.

2. Clear/Reset the Screen’s Drop Position to factory default:

Press & hold the “Programming Key + “Stop key” on the wall box controller.

Hardware Parts List for CineTension 3 Series

Please make sure all parts listed below are included before proceeding with the installation.

A. M12 Dry-wall anchor x 4 or 6

B. Bolt x 2 or 3

C. Masonry Screw x 4 or 6

D. Extruded Hanging Bracket x 2 or 3

120” & above x 3 brackets

Installation Instruction

Wall Screws included with this product are complimentary and may not be adequate for all mounting surfaces.

Consult with a professional installer or hardware store for proper mounting screws and anchors.

Elite Screens is not liable for any faulty installations.

1. Insert each Bolt (B) through the right & left slide channel

located on the top of the screen’s case.

ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the projection surface

on tab-tension screens. The full drop is recommended to allow the screen to rely on the tab-tension system

to maintain the projection surface flat and taut on all sides.

The same applies on non-tensioned screens, although some level of waves may be present due to the nature

of the screen not being tensioned. If wrinkles/waves develop after making the adjustment to the desired drop

position, reset it to the factory’s default position per the instructions below.

FLATNESS AFFECTED BY NEW PROGRAMMED VERTICAL POSITION IS NOT COVERED UNDER A REPLACEMENT

WARRANTY.

PROGAMMING NOTE:

The programmed vertical position relies on a time-count which adjusts itself according to the programmed

timed difference. Multiple up/down programming will result in the vertical position being off a few inches. It

is recommended that programming is done the first-time the desired vertical position is determined or RESET

it to factory default and programming the desired vertical position afterwards.

Rev. V06142023DT (DS8621) 6 www.elitescreens.com

2. Slide the Extruded Hanging Bracket (D) through the rail located below the

slide channel until it meets with the top of the Bolt (B) and slightly secure

the lug-nuts located on the top & bottom of the bolt to attach the bracket.

3. Mark the installation location to drill your hole. Insert the

proper screw and secure the bolts to the bracket.

4. Example of the CineTension 3 installed to a wall, ceiling and enclosed.

Adjusting the Tension String

There are adjustment knobs located at the end of the weight bar of the screen. If for any reason the tension string(s) is

loose, you can re-tension it by adjusting the tension string(s)knobs. The tension should be equally balanced in order to

provide a flat, uniform projection surface.

Attention: The screen’s tension has been preset to achieve its best performance. The adjustments are

typically not required. Please contact Elite Screens for assistance to avoid damaging the screen and voiding

your warranty.

For local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Flush mount

to wall

Flush mount

to ceiling

Enclosed

installation

*Allow 2” of spacing

between the front and

back of the screen casing.

Direction of

wrapping thread:

Adjustment Knob

Adjustment method: Pull out the

adjusting knob and rotate it to

tighten or loosen tension string. The

direction to tighten/loosen the string

will depend on the direction of the

wrapping thread.

Attention: The string and screen

will lose all tension if the string is

loosened to its maximum. To reverse

this, simply turn the knob in the

opposite direction.

Top hole for

ceiling installation

Back hole for

wall installation

A & C

PARTS

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens 100 series Manual de usuario

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Guía de referencia rápida

Elite Screens

Elite Screens Lunette Series Manual de usuario

Elite Screens

Elite Screens Sable Frame B2 Series Manual de usuario

Elite Screens

Elite Screens M135XWV2 Manual de usuario

Elite Screens

Elite Screens OMS90H2 Manual de usuario

Elite Screens

Elite Screens Saker Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens DIY Wall 2 Series Manual de usuario

Elite Screens

Elite Screens ezCinema Series Manual de usuario

Elite Screens

Elite Screens Kestrel Home Series Manual de usuario

Elite Screens

Elite Screens Kestrel FE100H Manual de usuario

Elite Screens

Elite Screens Reflexion Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens PicoScreen Series Manual de usuario

Elite Screens

Elite Screens Kestrel Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens GolfSim Portable Series Manual de usuario

Elite Screens

Elite Screens Raptor Series Manual de usuario

Elite Screens

Elite Screens Aeon CineGrey 3D AT Series Manual de usuario

Elite Screens

Elite Screens Evanesce AcousticPro UHD Series Manual de usuario

Elite Screens

Elite Screens QuickStand Drape Series Guía de referencia rápida

Elite Screens

Elite Screens aeonclr series Manual de usuario

Elite Screens

Elite Screens QuickStand Series Guía de referencia rápida

Elite Screens

Elite Screens M100S Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación