Elite Screens Elite Ez-Frame Series Manual de usuario

Rev. 042409-JA

www.elitescreens.com [email protected]

Elite Ez-Frame Series

Fixed Frame Projection Screen

User’s Guide

Parts List

1. Frame Parts x 6 pcs (4 top frame pcs. + 2 side frame pcs)

2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods)

3. Screen Material x 1 pc

4. Center joints x 2 pcs

5. Elbow Joints x4 pcs

6. Wall brackets x 2~3 pcs

7. Screws x 16 pcs

8. User Guide x 1 pcs

9. Center Support Bar x 1~2 pcs (depending on model)

10. Support joiner x 2~4 pcs (depending on model)

11. Fix Plates x 30~90 pcs (depending on model)

12. Black cloth backing x 1 (AcousticPro1080 models only)

Note: Please make sure all parts are included in your package before proceeding to assemble your

Elite Screens fixed frame projection screen.

ASSEMBLING THE FRAME

1. Insert joint connector to horizontal frame piece and then fasten it with 2 screws

2. Insert the other horizontal frame piece to the joint connector and then fasten it with 2 screws.

(1)

1/2Long frame

Push

Please do not tighten the screws completely, to make sure the frame piece lines up

correctly.

3. Insert both corner joint connectors into the long horizontal frame (see fig.1)

(2)

Push Push

Short frame

Push Push

Joint

Long frame

( fig.1)

Push Push

( fig.2)

Insert the exposed ends of the joint connectors

into the short (vertical) frame and align the four

corners so that they meet at perfect right angles

4. Join all four frame parts together following the steps showed below. (fig.2)

5. After making sure that all four corners join at right angles to form a perfect rectangle, fasten the four

angles together by using the (x8) joint screws included. (see fig.3)

6. Lay out the screen and tension rods on a clean and dry surface. Pass the screen

tension rods through the sleeves according to their corresponding lengths on each

edge of the screen as seen below. (see fig.4)

(3)

Screw

( fig.3)

Tension Rod (Horizontal) x 4

Tension Rod (Vertical) x 2

Tension Rod (horizontal)

Push

Tension Rod (Vertical)

Attaching the screen material to the frame

1. Lay out the screen and tension rods on a clean and dry surface. Insert the screen tension rods through

the sleeves according to their corresponding lengths on each edge of the screen as seen below. (see fig.4)

2. Place the screen material on the back of the built frame and slip the tension rods into the grooves

running along each side on the back of the frame on all four corner and clip on the fix plates to the back of

the frame to secure the rods into place creating tension for a tight and flat surface

(see fig. 5 & fig. 6)

(4)

Steel rod

Push

( fig.4)

Steel rod

Screen

Push

Rod

Push

( fig.5)

Viewing surface

(Front of screen) Steel rod

fix plate

Tension Rod

(fig. 5) (fig. 6)

Black backing for AcousticPro1080 models

This procedure only applies to AcousticPro1080 models, disregard if your ezFrame is not an

AcousticPro1080 variant. The black backing counters the effects of light penetration that

would otherwise light up all items behind the screen and spoil the picture.



（

fig.6

）

(5)

Fix plate secures AcousticPro1080 material and

the black

backing

behind it.

AcousticP

o1080 Sc

een

Material

Cover

Black backing

Fix Plate

Tension Rod (stretches the

AcousticPro1080 material)

Black backing for

AcoousticPro1080

*An alternate way to attach the black backing is to utilize the Velcro tabs attached to the tops of the fix plate’s tail

(Fig. 4). The material will grab and hold tight to the Velcro as it lays over the tails of the fix plates themselves and

stretched from tab to tab around all four sides.

After the material has been installed, the backing will lay over the back of the white (AcousticPro1080) material and

then be held into place by the fix plates as they are added (Fig.1-3). Interval markings reveal the best likely points of

attachment (Fig. 1). The prongs on the fix plates (Fig. 2) straddle a lip on the back of the frame creating a friction

hold that will firml

kee

the material and backin

lace

(

. 3-4

)

The black backing goes behind the projection surface and are held into position by Velcro-faced fix plates.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

Black backin

Attaching the Fix Plates___

1. Make sure that the material and frame are both laying face down on a clean, dry and non-abrasive

surface.

2. Center the material inside the frame.

Please note the material will be noticeably smaller because stretching the material is required to create

a sufficient amount of tension for perfect material flatness.

3. Start attaching the fix plates in the center of the long horizontal edge and (1) then alternate with the

center short sides (2) as shown in diagram (fig.7).

Note: Follow these instructions to make sure the material is properly fixed in the center position of the

frame. After attaching the fix plates in sequence #2 (the center of the short sides), please remove the fix

plates in sequence #1 (the center of the long horizontal edge) and reattach them again, and also remove the

fix plates on sequence# (2) and reattach them again.

4. Then continue to follow our recommended order numbers 3-8 to properly distribute tension to the

screen material.

Center Support Bard

1. Insert the support joiner into each side of the center support bar to complete assembly.

supportjoiner

Center support bar

2. Insert the Center Support Bar into the groove on the back of the frame with the bottom end near the

approximate center point of the frame and place it in at an angle so that both ends of the bar are in

alignment with the groove. (see Fig. 8 below for details).

(6)

(Fig. 7)

3. Slide the top end of the bar into the top center point location to complete center support bar

installation. This will provide added stability to your frame and added tension to the material.

Installation

1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole

area of where the screen is to be installed.

2. Drill a hole with the proper bit size according to the wood screws included.

3. Line up the small wall brackets with the drilled holes on the installation location and screw them in

using a Philips screwdriver.

4. Position the fixed frame screen onto the top wall brackets as shown in (fig. 9) and push down at

the center of the bottom frame rail to hook into the lower wall bracket.

(7)

small wall bracket

4pcs

( fig.7)

Method 1 (smaller than 135" diagonals)

Center Support Bar

(Fig. 8)

CAUTION

Please follow these instructions carefully to ensure proper maintenance and safety

with your ezFrame Screen

1. When hanging the screen up, please make sure that no other objects such as power switches, outlets,

furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen.

2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting

anchors are used and that the weight is supported appropriately by a strong and structurally sound surface

just as any large and heavy picture frame should.

(Please consult a home improvement specialist for the best advice on installation)

3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care.

4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any

other impurities.

5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen

surface.

6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.

7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other

sharp or abrasive objects.

8. Spare Parts should be placed out of reach of small children in accordance with household safety

guidelines.

(8)

small wall bracket

7pcs

Position the screen with the

attached surface onto the top

wall bracket as shown in (fig.8).

Push down at the center of the

bottom frame rail to hook onto

the lower wall bracket

( fig.8) 2

OVERALL

HEIGHT - 1/4"

OVERALL

HEIGHT

Method 2 (larger than 135" diagonals)

(fi

. 9)

WARNING

•The projection screen frame is made of high-quality aluminum alloy and should be handled

with care.

•Use a soft cloth with warm water to remove any spots on the screen surface.

•To avoid damaging the screen material, never attempt to use any solutions, chemicals or

abrasive cleaners on the screen itself and never attempt to touch screen with your fingers or

sharp/abrasive objects.

Warranty Policy

•Two (2) year warranty on parts and labor from defects in workmanship from purchase date as follows (except for

refurbished units as specified below):

•Refurbished units carry a T90-dayTparts and labor warranty.

•TDemo units or open box items are “TAS IS”Titems and do not carry a warranty.

•Each party will be responsible for one way shipping during the warranty return/exchange.

•TDOA (Defective on Arrival): Must be reported within 7 business days of receipt. An RMA (Return Merchandise

Authorization) number must be issued in order to process a replacement. Elite Screens will replace the DOA

(Defective on Arrival) unit with a brand new replacement *(see exceptions below) after the DOA unit is received

and/or confirmed defective. Once the product is received, Elite Screens will send out a new *unit to the customer by

ground service (subject to inventory availability). Should a problem be reported after the 7-day grace period, the item

must be shipped to us for warranty repair.

•TMissing Parts must be reported within the 7-day (DOA) grace period. If reported after 7 days, customer will be

only be responsible for shipping and handling fees up to 30 days. If reported after 30 days of receipt, customer is

responsible for cost of the parts and shipping & handling fees.T

•DO NOT return any unauthorized items to Elite Screens, as they will be refused at shipper’s expense.

The RMA number must be included on the outside label of your shipping box and shipping documents. Our

warehouse is not authorized to accept returns without an RMA number on the shipping label. RMA numbers

are valid for 45 days from the date of issue.

*A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished)

or based on stock availability.

For Warranty and Service requests please fill out a RMA /Service Form at:

http://www.elitescreens.com/service_form.htm.

Please Visit this link for full Warranty information:

http://www.elitescreens.com/service.htm

For Customer Service and Technical questions, please contact Elite Screens at:

Telephone: (877) 511-1211 Fax:(562)-483-8498

(9)

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens PicoScreen Series Manual de usuario

Elite Screens

Elite Screens VMAX113XWS Manual de usuario

Elite Screens

Elite Screens SilverFrame 100GH1 Manual de usuario

Elite Screens

Elite Screens AR120WH2 Manual de usuario

Elite Screens

Elite Screens Osprey Tension Dual Series Manual de usuario

Elite Screens

Elite Screens M135XWV2 Manual de usuario

Elite Screens

Elite Screens VMAX 2 Series Manual de usuario

Elite Screens

Elite Screens Raptor Series Manual de usuario

Elite Screens

Elite Screens Evanesce Tab-Tension ITE120HW2 Manual de usuario

Elite Screens

Elite Screens TE200HR2 Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Guía

Elite Screens

Elite Screens Kestrel Home Series Manual de usuario

Elite Screens

Elite Screens CineTension 2 Series Manual de usuario

Elite Screens

Elite Screens B SERIES Manual de instrucciones

Elite Screens

Elite Screens QuickFold Q100V Manual de usuario

Elite Screens

Elite Screens Home100IWH3 Manual de usuario

Elite Screens

Elite Screens F100NWH Manual de usuario

Elite Screens

Elite Screens GolfSim Bay Series Manual de usuario

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Guía

Elite Screens

Elite Screens Electric100H Manual de usuario

Elite Screens

Elite Screens VMAX2 (Plus) Series Guía

Elite Screens

Elite Screens YardMaster 2 WraithVeil Dual Series Manual de usuario

Elite Screens

Elite Screens YardMaster 2 Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación