Elite Screens Evanesce B Series Manual de usuario

In-Ceiling Front Projection Screen

Evanesce Series

User’s Guide

Important

Safety

and

Warning

Precautions

Be sure to read this user guide before use and follow the procedures below.

Please retain this manual for future reference.

To avoid any damage, do not use in conjunction with any accessories not recommended by the manufacturer.

Handle the device carefully during transportation to avoid damage.

To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.

The power outlet supplying power to the unit should be close to the unit and easily accessible.

Do not install the device on uneven or inclined surfaces.

Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle.

Never overload the power cord to prevent an electric shock or fire.

Guard the device from any liquid or foreign objects to avoid electrical shock or fire due to loose contact or

short circuit.

There are no user serviceable parts in the device. Do not attempt to disassemble this device by yourself. No

one except authorized technicians can open this device to make repairs.

Make sure the power source this device is connected to has a continuous power flow.

If there is a need to use an extension cord, make sure the cord has the same equal rating as the appliance to

avoid overheat.

Do not handle the power plug when your hands are wet or your feet are in contact with water.

2. Do not use this device under the following circumstances:

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lighting.

Avoid direct sunshine, rain shower or moisture.

Keep away from fire sources and high temperature to prevent this device from overheating.

Cut off the power supply first before transportation or maintenance.

Fully disconnect from the power supply when screen is not in use for a long period of time, as should be

done with any other electric household appliance.

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or if

there are any evident broken parts

WARNING:

The screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra black top drop in the

roller. Please be aware of this as it will void the limitation of your warranty.

Changes or modifications (except cutting the power cord for hardwire installation) to this unit not expressly

approved by Elite Screens is prohibited and will void the warranty.

Accessories for Evanesce Series

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna of the device which may be causing interference

Increase the separation between the screen and the device’s receiver

Connect the equipment into a different power outlet than the device’s

Consult the dealer or an experienced Radio/TV technician for help

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles

such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on

the viewing surface will not cause the casing to become loose or fall. The installer must insure the fasteners that

are used are of adequate strength and suitable for the installation location.

Red 12V (+) Green 0V (-)

E. 5-12 volt trigger

adaptor cable

G. AAA

Batteries

A. IR Remote B. RF Remote C. 3-way switch

F. Bubble level

D. IR ”eye”

receiver

1. 5-12V Trigger: The built-in 5-12V trigger

input for your new CineTension2 allows your screen

to synchronize its drop and rise with the projector's

power cycle. The screen drops when the projector

powers up and retracts when the projector powers

down. The 5-12 volt adaptor connects to your

projectors trigger output via a separate cable that may

or may not be provided by the projector manufacture.

The trigger feature will not work without an output

cable from the projector, but it can be tested using a

9-volt battery by simply connecting the Red (+) and

Green (-) cable to the 9-volt battery.

2. 3-Way Wall Switch: The 3-way wall

switch is a wall mount control box with an

up/stop/down button and plugs directly

into the screen’s RJ45 port.

3. Infrared (IR) and Radio Frequency (RF) Remote Controls: Although the IR remote requires a direct line of sight

with the IR sensor to function, the screen’s case can be hidden from sight and operated using the RF remote. When

depressing the directional buttons you should hear a faint click signifying that the mechanism is working properly.

*The IR remote can also work with a Universal Learning Remote Control usually by programming the Screens IR codes into

your Universal Learning Remote. Consult your Universal Learning Remote’s manual for programming instructions.

This is the IR remote

with a range of 25 Ft.

Requires 2x AAA

batteries.

Stop

Down

This is the RF remote

with a range of 100 Ft.

Requires 2x AAA

batteries.

RJ-45 input for 5-12 v

trigger

5-12V RJ45 cable

RJ45 port location for IR

“eye” sensor

RJ45 port location for

3-way switch

3. IR “Eye” Receiver: plugs directly into the

screen’s RJ45 port to present a low profile line-

of-sight control option for your IR remote

control even in a recessed ceiling installation.

Hardware Parts List for Aerie Tension Series

Please make sure all parts listed below are included before proceeding with the installation.

Installation Instructions

The Evanesce allows access for above or below ceiling installation. Please follow the instructions described in the

following steps below for your type of installation.

Power

The Evanesce series screen includes a 3-prong power cord for using in a non-concealed power outlet. If your

installation however will be entirely concealed including the power outlet, we strongly recommend a hardwire

connection. Please refer to the diagram below for wiring information for both 110v and 220v variants.

Hardware Parts List

QTY

A. Case Rail Nut

4-6

B. Hex Screw

4-6

C. Hanging Bracket

2-3

D. Suspension Bar

E. Washer

8-10

F. Hex Nut

4-6

G. M8 Top Expanding Bolt

H. M8 Threaded Rod

I. M8 Screw Nut

J. M8 Hexagonal Screw

K. M8 Screw Washer

L. Installation Bracket

M. Socket Wrench

N. White cover flange panel

A. Above ceiling installation instructions

Assembly

2. Hanging bracket Assembly

Place the Hanging Bracket (C) over the Casing Rail Nut (A) that’s located inside the channel of the screen’s case

and secure it with the Hex Screw (B)

3. Suspension Bar Installation

Place the Suspension Bars (D) on the Hanging Bracket (C) and align with the hole as shown below. Secure the

Suspension Bar (D) with the Hex Screw (B), Washer (E) and the Hex Nut (F). Install the Suspension Bars (D) to

your ceiling according to their distance.

B. Below ceiling installation instructions

1. Measure and cut the ceiling installation space. The width should not exceed 120mm. Please refer to the length

on the screen size table (C3).

Note: The length of the installation space is not greater than the screen size table (C3), and the width is not less

than the screen size table (A5). Consult the table below (C1) in regards to accommodating the screen casing.

(N)

(K)

(H)

The ceiling wall

Install screw holes

Ceiling

Ceiling installation space

2. Drill 4 holes in the ceiling that correspond with the attachments on the various casing sizes.

3. The expanding bolts (H) mount into thick wood beams, stone or concrete and will support the screen. Use

the Socket wrench (N) to attach the hexagonal screws (K). The expanding bolts should be firmly tightened

and tested to make sure that they will hold the weight of the screen.

Ceiling Panel

The ceiling truss

4. Push the screen up into the space. Use the threaded rods (I) to attach the screen assembly to the ceiling.

The hexagonal screws (K) will connect the screen to the rest of the assembly. Once firmly in place, use the

nuts (J) to ensure a firm connection. Use the socket wrench (N) to make sure that the bolts are firmly

tightened.

5. Install plastic cover panel (O) to complete the installation.

For local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Ceiling

Socket wrench (H)

Push

Ceiling

(J) and (L)

(I)

(K)

(M)

Otros manuales para Evanesce B Series

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens VMAX113XWS Manual de usuario

Elite Screens

Elite Screens Kestrel Tab-Tension 3 CineWhite X Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens F100NWH Manual de usuario

Elite Screens

Elite Screens M170XWS1 Manual de usuario

Elite Screens

Elite Screens PicoScreen Series Manual de usuario

Elite Screens

Elite Screens Evanesce AcousticPro UHD Series Manual de usuario

Elite Screens

Elite Screens SILVERMAX106H2 Manual de usuario

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Manual de usuario

Elite Screens

Elite Screens Daywalker Series Manual de usuario

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens CineTension2 Series Guía de referencia rápida

Elite Screens

Elite Screens Pop-Up Cinema Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Guía de referencia rápida

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens Spectrum 2 Series Guía de referencia rápida

Elite Screens

Elite Screens F100XWH1 Manual de usuario

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Manual de usuario

Elite Screens

Elite Screens Lunette Series Manual de usuario

Elite Screens

Elite Screens VMAX2 (Plus) Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación