Elite Screens QuickFold Q100V Manual de usuario

Folding Presentation Screen

QuickFold Series

Users Guide

Setup Procedure

The frame and supports are made of 1 3/8” aluminum tubing with an anodized finish. Please follow the instructions in

this package. With proper care, your QuickFold screen will provide many years of reliable service.

fig 2

Top

fig 1

Two Section Frame

(For presentation screens that are less than 120” in diagonal measurement)

1. Take the frame out of the case and remove its wrappings. Unfold the

main joints as shown in (fig 1).

2. Once the main joints are unfolded, make sure that the snap latches

“click” into the locked position. The frame should now be fully

elongated as in (fig2). *Note: The snap latches will automatically

lock when the joint is straightened. Press the snap latch button in

order to release the lock.

3. While holding the bottom of the frame in place, lift the top of the

frame to unfold the sides which will cause the snap latches lock

when fully extended. Secure the corner braces into the locked

position. The screen frame should now be fully opened as in (fig 3).

fig 3

Lock down the corners

Snap latch

Top

Three Section Frame

(For large presentation screens that are 120” or more in diagonal

measurement)

1. Take the frame out of the case and remove its

wrappings. Unfold the main joints making sure that

both the end and middle spans are in prefect alignment

as shown in (fig 4).

2. Make sure that the snap latches have locked the joints in

the frame so that it is at its full horizontal extension as

shown in (fig 5)

3. While holding the bottom of the frame in place, lift the

top of the frame to unfold the sides which will cause the

snap latches lock when fully extended. Secure the

corner braces into the locked position. The screen frame

should now be fully opened as in (fig 6).

fig 4

Top

fig 5

fig 6

Lock down the corners

Snap latch

Top

Standard T-Leg Support

1. Take the T-Leg out of the case and remove its wrappings.

Fold down the support legs as shown in (fig 7).

2. Secure the corner braces into the locked position as shown

in (fig 8)

3. Unfold the T-Leg’s main support until the snap latches

“click” into the locked position as in (fig 9).

fig 7

fig 8

Lock down the corners

fig 9

Snap latch

locking bolt

frame spacer

fig 12

fig 10

fig 11

Snap latch

AT-Leg (optional support buttress recommended for the

large screens with diagonal measurements of 150” and

over)

1. Take the AT-Leg buttress out of the case and remove its wrappings. Unfold the buttress as shown in (fig 10).

2. Snap latches will automatically lock in the center joint. Use the snap latch buttons to unlock the end joints as

shown in (fig 11).

3. Attach the AT-leg to the T-Leg by securing the locking bolts through the frame using the frame spacers

between the metal parts as shown in (fig 12) (*Note: It is important to always use the plastic frame spacers

between the pieces whenever connecting any of the aluminum surfaces such as T-bars to AT, SAT and Frame

components.)

lockingbolt

frame spacer

fig 15

fig 13

fig 14

SAT-Leg (optional added stability buttress recommended

for the large screens with diagonal measurements of 180”

and over)

1. Take the SAT-Leg out of the case and remove it wrappings as shown in (fig13).

2. Undo the snap locks to loosen and bend the joints for proper fitting as shown in (fig 14).

3. Attach the SAT-Legs by securing the locking bolts through the frame using the frame spacers between the metal

parts as shown in (fig 15)

lockingbolt

frame

leg

frame spacer

ttaching the Frame to its Supports

1. Always use at least two locking bolts through the T-Leg Support, the Spacer and into the Frame on each side.

2. Height can be adjusted in 8” increments up or down. Normal screen height is 44” from the bottom of the frame to

the floor.

3. Reverse this process to dismantle and pack away the screen.

snap latch button

Folding the Picture Surface for Packing

Please observe the following precautions before folding up the screen material.

1. Do not bring the viewing surface into contact with chemical solvents, sharp or abrasive objects, painted,

varnished or plastic finished items.(*See the cleaning instructions for exceptions to this)

2. Make certain that the screen is laid out on a dry, clean and flat surface.

Folding up the screen:

Lay out the screen with the viewing surface facing up and cover it with flat (not crumpled) tissue or packing paper that is

clean and unprinted. *Note: Do not ever use abrasive paper, newspaper or any printed material on your projection

screen.

1. With the viewing surface facing up, fold the fabric in half from top to bottom. When folding, make certain that

the viewing surface does not come into contact with the black binding, grommets or snap buttons. *Note: The

screens are shipped from production with tissue paper in the folds that should be retained for future use.

2. Make sure that the first folds never exceed 3 feet in width (fold again if necessary). Also make sure that there is

always clean packing paper in between the two surfaces.

3. Larger sized screens will need to be folded with more frequency than smaller screens. Follow the instructions

from step 1 as well.

4. Fold the material from top to bottom first then alternate in folding left to right until the material is of a sufficient

size that will fit into the leatherette case.

Note: Keep the screen material inside its case when not in use.

Failure to follow this precaution may eventually result in

staining or discoloration.

Cleaning

The screen surface can be cleaned as follows.

Use a clean white cloth (100% cotton preferred) and dampen it with clear water. Gently wipe in one direction and NOT

in a circular motion. Use another dry cloth to dry after each cleaning session. To remove a stubborn stain or sticky

surface, use denatured alcohol (methanol or methyl alcohol) in lieu of water.

Attaching the Screen once it is unpacked

1. Using the snap buttons to connect the Screen material with the case

2. Start at the top working in whatever direction is most comfortable to you

3. Stretch the corners if necessary to pair up the buttons with their corresponding snaps

Packing List

1. Frame 1 piece

2. Support (T) Legs 2 pieces

3. AT-Legs 2 pieces (optional depending on size)

4. SAT-Legs 2 pieces. (optional depending on size)

5. Screen Fabric 1-2 pieces

6. Locking Bolt 6-26 pieces

7. Frame Spacer 6-26 pieces

8. Manual 1 pieces

The following points should be noted to assure the sound performance and longevity of your

screen

1. Never use your hand to touch the screen surface.

2. Never scrabble on the screen with anything.

3. Don't touch the screen with hard or sharp objects.

4. Please use a clean cotton cloth or soft dust brush to remove any dust particles on the screen.

5. The screen material may be cleaned

Warranty Policy - Manual, Tripod, Pull-up Floor, and Fixed Frame Screens

*Warranty policy applies to claims made in the United States of America. Warranty issues outside of the US must go

through their international distributor.

•Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified

below):

•Refurbished units carry a 90-day parts and labor warranty.

•Demo units or open box items are AS IS items and do not carry a warranty.

•Elite Screens will cover ground shipping charges on warranty claims made within 7 days of receiving per our

DOA (Defective On Arrival) policy

•Each party will be responsible for one way shipping during the regular warranty period if the claim is made

after the 7 day DOAperiod.

•An RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite

Screens will either replace or repair the defective unit with a brand new replacement *(see exceptions below)

after the defective unit is received and/or confirmed defective. Once the product is received, Elite Screens will

send out a new *unit to the customer by ground service (subject to inventory availability).

•Missing Parts must be reported within the 7-days of receipt. If reported after 7 days, customer will only be

responsible for shipping and handling fees. If reported after 30 days of receipt, the customer is responsible for

cost of the parts and shipping & handling fees.

Please visit the link below for full warranty information

http://www.elitescreens.com/services.html

*Anew or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) and is

based on stock availability. 安装幕布分别将幕布四个角上的按扣扣在框架上，再依次扣上余下的按扣

TWO WAYS TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC.

A. On Line (Faster and Easier) www.elitescreens.com/register.html

B. Fill out & Fax to (562) 483-8498,Attn: Customer Service Dept.

*Your Name: _______________________________________________________

Address: ____________________________________________________________

City/State/Zip ________________________________________________________

*Email Address: ______________________________________________________

*Phone: _____________________________________________________________

*Screen Model: _______________________________________________________

*Serial Number: _______________________________________________________

*Date of Purchase: _____________________________________________________

*Dealer / Reseller Purchased from (name of the reseller): _____________________

What is your Projector Model :____________________________________________

Application: ___ Home ___ Education ____ Corporation _____ Government

___ Others

How would you rate this screen? ___ Excellent ___ Good ___ Ok ___ Improvement needed

Comments:

Contact info:

If you have pictures of your screen you’d like to share with us, please

email your pictures to [email protected]

or call us at 877-511-1211

www.elitescreens.com

For any technical inquiries,

techsupport@elitescreens.com

Otros manuales para QuickFold Q100V

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Guía de referencia rápida

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens ITE139XW3-E8 Manual de usuario

Elite Screens

Elite Screens Yard Master 2 Series Manual de usuario

Elite Screens

Elite Screens Spectrum Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens YardMaster 2 Series Manual de usuario

Elite Screens

Elite Screens Elite Home 2 Series Manual de usuario

Elite Screens

Elite Screens FE72V Manual de usuario

Elite Screens

Elite Screens WhiteBoardScreen Series Manual de usuario

Elite Screens

Elite Screens VMAX113XWS Manual de usuario

Elite Screens

Elite Screens Elite Home Series Manual de usuario

Elite Screens

Elite Screens Evanesce Tension B Series Manual de usuario

Elite Screens

Elite Screens IWB85SW2a Manual de usuario

Elite Screens

Elite Screens CineTension 2 Dual Series Manual de usuario

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Elite Screens

Elite Screens Manual Series Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens aeonclr series Manual de usuario

Elite Screens

Elite Screens Starling 2 Series Manual de usuario

Elite Screens

Elite Screens Kestrel Tab-Tension 2 CLR Series Manual de usuario

Elite Screens

Elite Screens PowerMax Series Manual de usuario

Elite Screens

Elite Screens WhiteBoardScreen Universal Series Manual de usuario

Elite Screens

Elite Screens Lunette Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación