Elite Screens AEON series Manual de usuario
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 1 www.elitescreens.com
Thank you for choosing the Aeon Series projection screen! Please read through this user guide before
utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the
points below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen
material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A. Center Joints
B. Spring
C. Elbow Joints
D. Long Screw, Short Screw &
Washer
E. Pull Hook
F. Wall Bracket
G. Wall Anchors, Screw &
Washer
H. Tension Rods
I. Center Support Bar and
Small screws
J. Rubber End Cap
K. Screwdriver and Rubber
hammer
L. Pair of Gloves
Note: The parts listed above are subject to change without notice.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 2 www.elitescreens.com
Frame and Edge Trim Parts
Qty Item
Main Frame Parts
Qty Item
Edge Trim Parts
2 pcs
Vertical Frame (A)
2 pcs
Vertical Velvet Trim
2 pcs
½ Horizontal Frame (B)
4 pcs
½ Horizontal Velvet Trim
2 pcs
½ Horizontal Frame (C)
Item
Part List
120” Screen
A
Center Joints
2
B
Spring
58
C
Elbow Joints
4
D
M5x16mm Long Screw, M5x10mm Short Screw & Washer
12/32/32
E
Pull Hook
1
F
Wall Brackets
2
G
5x70mm Wall anchors, M5x70mm Screw & Washer
4/4/4
H
Tension Rods
6
I
Center Support Bar & M4x10 Small Screws
1/4
J
Rubber End Cap
8
K
Screwdriver & Rubber Hammer
1/1
L
Pair of Gloves
1
Frame Assembly
Step 1. Place a soft-clean cloth on the ground or other flat surface of the area where the screen will be
assembled.
Step 2. Position the pieces of the frame face-down on the soft-clean cloth in the arrangement shown below.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 3 www.elitescreens.com
Step 3. Insert the Center Joint (A) connectors into one-half of the horizontal frame and secure with 4
(M5x10mm) screws. Once secure, connect the other half of the horizontal frame and fasten with 4 more
screws.
Step 4. Connect the Elbow Joints (C) to top and bottom sections of the vertical frame. Once inserted,
connect the vertical sections to the horizontal frame sections.
Make sure all the holes are in alignment and the frame
pieces are flush (no gaps). They should form perfect right
angles. NOTE: Do not tighten elbow joints completely
until all frame pieces are assembled correctly.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 4 www.elitescreens.com
Center Support Bar Installation
Step 1. Two people are suggested for this step. Place the Center Support Bar (I) into the top groove of the
back of the frame.
Step 2. Next, slowly push and slide the opposite side of the center support bar towards the center as shown
below.
Step 3. Using the (M4x10) screws, screw both ends of the center support bar and make sure it is secure.
Screen Material Installation
Step 1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal
position. The back side of the screen material should be placed upwards.
Step 2. Carefully and gently place the assembled frame on top the screen material as shown below. Make
sure to not allow the angle edge of the frame to come in direct contact with the screen material to avoid
puncturing it.
Step 3. Insert the four horizontal and two vertical Tension Rods (H) into the corresponding sides of the
screen material, while keeping the material laying flat. Careful not to snag on the holes at the edge of the
material during this process; forcing the rods may damage the screen material.
Step 4. After the Tension rods (H) have been inserted, make sure to have all corners aligned to the frame
and fold over the material on each corner. NOTE: Make sure to stretch the material tightly over the frame to
maintain a flat surface.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 5 www.elitescreens.com
Step 5. Starting from all four corners, hook the Springs (B) through the hole located on the screen
material’s outer edge. First, hook the small spring head to the frame. Then using the Pull hook (E), hook
the other side of the spring to the material.
Step 6. After hooking the corner springs, work your way around the frame to hook the rest of the springs to
the material.
Step 7. Once the material is completely attached, place the black rubber end caps (J) at each of the tension
rod (H) ends.
Velvet Trim Installation
Step 1. Place the velvet frame pieces over each side of the frame and secure it using the M5x16 screws (D).
NOTE: Do not completely tighten the screws until you make sure each corner forms a right angle.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 6 www.elitescreens.com
Step 2. Make sure to secure the corner and center M5x16 screws (D) of the velvet frame.
Wall Mount Installation
Step 1. Locate your desired installation location and mark the drill-hole area of where the screen is to be
installed.
Step 2. Using the marked area, drill holes on the wall where the brackets (F) will be placed.
Step 3. Place the wall anchor (G) through the hole for each bracket on the frame.
Step 4. Line up the wall brackets with the drilled holes on the installation location and screw them in using
the M5x70 screw (G). Make sure the brackets are leveled.
Step 5. Next, using two people, carefully position the screen onto the wall. Your installation is now
complete.
Aeon Series
Fixed Frame Projection Screen
User’s Guide (Z-Type)
Rev. 072219-BR 7 www.elitescreens.com
NOTE: Due to the square design of the frame, we DO NOT recommend using an optional LED lighting kit
with this product. LED lighting kit will not be compatible.
For more information, technical support or your local Elite Screens
contact, please visit www.elitescreens.com
Otros manuales para AEON series
3
Tabla de contenidos
Otros manuales de Pantalla de proyección de Elite Screens
Elite Screens
Elite Screens ezCinema Series Manual de usuario
Elite Screens
Elite Screens M170XWS1 Manual de usuario
Elite Screens
Elite Screens SilverFrame 100GH1 Manual de usuario
Elite Screens
Elite Screens Spectrum2 Series Manual de usuario
Elite Screens
Elite Screens ITE139XW3-E8 Manual de usuario
Elite Screens
Elite Screens Aeon CineGrey 4D AT Series Manual de usuario
Elite Screens
Elite Screens Kestrel Series Manual de usuario
Elite Screens
Elite Screens M100S Manual de usuario
Elite Screens
Elite Screens PowerMax Series Manual de usuario
Elite Screens
Elite Screens Saker Series Manual de usuario
Elite Screens
Elite Screens EDGE FREE Aeon CineWhite UHD 2 Series Manual de usuario
Elite Screens
Elite Screens GolfSim Bay Series Manual de usuario
Elite Screens
Elite Screens Insta-DE Screen Manual de usuario
Elite Screens
Elite Screens Evanesce B Series Guía de referencia rápida
Elite Screens
Elite Screens Elite Vmax Series Manual de usuario
Elite Screens
Elite Screens Evanesce B Series Guía
Elite Screens
Elite Screens Daywalker Series Manual de usuario
Elite Screens
Elite Screens aeonclr series Manual de usuario
Elite Screens
Elite Screens Kestrel FE100H Manual de usuario
Elite Screens
Elite Screens Insta-DE Series Manual de usuario
