Elite Screens GolfSim Bay Series Manual de usuario
Rev.08242023JA 1 U00269 www.elitescreens.com
GolfSim Bay Series
Sport Simulation Impact Projector Screen
User Guide & Assembly Instructions
V1
For the latest updated version, visit www.elitescreens.com
Product Description: The GolfSim Bay Series is an enclosed golf and sport simulator impact screen that utilizes our
three-layer ImpactWhite® 1145. It includes a full frame assembly kit for permanent installation in dedicated spaces.
Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a
long product life.
ImpactWhite®1145 material tips and precautions
•Handle with caution, material is subject to static electricity.
•Wear gloves and unroll the material on a clean surface.
•Make sure to use the correct side. The ImpacWhite®1145 screen has a front and back side.
•Folding lines/wrinkles are normal due to the nature of the material structure and packaging but may be removed
with a steamer and/or light ironing set to no higher than Polyester.
•Make sure to allow proper distance for swing range to protect children, pets, ceilings, walls, windows, or any
other property.
•Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands.
2. Do not write or draw on the projection surface.
3. Do not point at the projection surface with your fingers or sharp objects;this will damage the screenmaterial.
4. Use a soft bristle brush or dry microfiber cloth to remove dust from the screen surface.
5. Do NOT use any solutions, chemical cleaning agents, alcohol, or abrasive to clean the screen surface.
6. When cleaning the projection surface, use a soft cloth dampened with warm water to remove any traces.
7. Do NOT rub or apply pressure when cleaning the surface.
Assembly video
Watch our assembly video by scanning the QR code!
We consider our impact screens a wearable item and the life of them will vary according to
their use. Avoid using golf balls with scuffs or markings to maximize the life of the screen.
If possible, use new golf balls.
Rev.08242023JA 2 U00269 www.elitescreens.com
Hardware Parts List
A
B
C
D
E
F
G
H
Item
Part List
GSB10x10
GSB12x10
A
M8 hex screw
30
30
B
Three-way corner connector
6
6
C
L-shaped connector
2
2
D
Straight connector
5
5
E
T-shaped connector
2
2
F
Ball bungee
55
59
G.
M8 Hex Wrench
2
2
H.
Foam tape
4
4
I
Vertical frame (30x30x1450mm)
8
8
J
Horizontal frame (30x30mm)
1480mm - 6pcs
1980mm - 6pcs
K
Inner frame (30x30x1180mm)
5
5
L
Foam tube for vertical frame (1500mm)
4
4
M
Foam tube for horizontal frame
1500mm-4pcs
2000mm-4pcs
N
Foam tube for inner frame (1200mm)
1
1
Fabrics
Item
Part List
GSB10x10
GSB13x10
a.
Golf screen
1
1
b.
Left side enclosure panel
1
1
c.
Right side enclosure panel
1
1
d.
Top enclosure panel
1
1
e.
Golf Screen top border panel
1
1
f.
Golf Screen side border panel
2
2
g.
Middle black backing panel
0
1
h.
Left/Right black backing panel
2
2
Rev.08242023JA 3 U00269 www.elitescreens.com
Exploded Diagram
Assembly Instructions
Step 1: Assemble all four vertical support frames (I) using the straight connectors (D) and fasten them using the
M8 Hex Wrench (G) and M8 hex screws (A). We will refer to them as ID.
A
D
I
I
I
I
I
I
B
B
B
B
B
B
C
C
D
D
D
D
D
E
E
J
J
J
J
K
K
K
K
K
ID
Rev.08242023JA 4 U00269 www.elitescreens.com
Step 2: Connect two horizontal frames (J) together using the t-shaped connector (E). Then attach two three-way
corner connectors (B) at each end to join frames ID and J together as shown below. Fasten with M8 Hex Wrench
(G) and M8 hex screws (A).
Step 3: Attach two L-shaped connectors (C) at the top of the vertical frame (ID) and attach all five inner frames
(K) to connectors (C, B, E). Then fasten them with M8 Hex Wrench (G) and M8 hex screws (A).
ID
ID
J
J
B
B
E
C
K
K
K
K
K
B
E
B
ID
ID
B
A
E
A
B
Screw holes must face inside.
Rev.08242023JA 5 U00269 www.elitescreens.com
Step 4. Attach a three-way corner connector (B) to inner frame (K) on all corners and attach a vertical frame (ID)
Next, attach a T-shaped connector (E) to the center inner frame (K), attach horizontal frame (J) to Band E
connectors and fasten with M8 Hex Wrench (G) and M8 hex screws (A).
Step 5. Assemble the two horizontal frames (J) with the straight connector (D). Then attach it to the three-way
corner connector (B) and fasten using the M8 Hex Wrench (G) and M8 hex screws (A).
K
K
K
K
K
ID
ID
B
B
E
J
J
B
B
Screws face up.
J
J
D
B
B
J
J
D
Rev.08242023JA 6 U00269 www.elitescreens.com
Foam tape application
Step 6. Peel off the back of the foam tape (H) and adhere it to the frames as shown in the illustration.
Rev.08242023JA 7 U00269 www.elitescreens.com
Projection (Front) Side
Back Side
Golf Screen Installation
Step 7. Preparing to hang the golf screen on the frame.
7-1. Distinguishing the front and back side first.
7-2. Using the ball bungees (F)
7-3. Fasten the two top corners first. Use two ball bungees in each corner.
1. Insert the loop end of the
ball bungee through the
grommet.
2. Wrap it over the frame.
3. Hook it over the ball.
Note: Ball should end up on
the back side.
1
1
Two ball bungees go
through the same grommet.
G
Rev.08242023JA 8 U00269 www.elitescreens.com
Step 8. Lift and stand up the frame. Continue attaching the Golf screen to the frame in the following order.
Enclosure panels installation
Step 9. Left and Right Enclosure panels
9-1. Distinguish the front side and back sides. The front has the loop (fuzzy) and the back has the hook (rough).
Loop side = Front
Velcro should
be pulled apart.
2
3
4
5
6
7
Use only one ball bungee
at the bottom corners.
Hook side = Back
Top
Bottom
Rev.08242023JA 9 U00269 www.elitescreens.com
Velcro strip faces outside.
9-2 Attach the top of the panel first. Assure a tight and taut finish.
9-3. Attach the bottom side. Assure a tight and taut finish.
9-4. Attach the sides with ball bungees (G).
Attach the top
flap of the panel
with the velcro.
Pull the bottom of the
panel under the frame and
attach it with the velro.
Black panel
Rev.08242023JA 10 U00269 www.elitescreens.com
9-5 Lastly, attach the edge with velcro.
9-6. Repeat step 9-1 ~ 9-4 for the other side.
Step10. Top enclosure panel
10-1. Hang the top panel (d), pull it tightly and attach it to the Velcro strip on each side panel.
Velcro strip
Attach to align with the bottom
edge of the Velcro strip.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Pantalla de proyección de Elite Screens
Elite Screens
Elite Screens Spectrum Series Manual de usuario
Elite Screens
Elite Screens FE72V Manual de usuario
Elite Screens
Elite Screens Pop-Up Cinema Series Manual de usuario
Elite Screens
Elite Screens Sable Frame B2 Series Manual de usuario
Elite Screens
Elite Screens F60XWV1 Manual de usuario
Elite Screens
Elite Screens 2 CLR Series Manual de usuario
Elite Screens
Elite Screens AR100H Manual de usuario
Elite Screens
Elite Screens Manual Series Manual de usuario
Elite Screens
Elite Screens ezCinema Series Manual de usuario
Elite Screens
Elite Screens SILVERMAX106H2 Manual de usuario
Elite Screens
Elite Screens EZ-Cinema Series Guía de referencia rápida
Elite Screens
Elite Screens Starling Tab-Tension CLR 3 Series Manual de usuario
Elite Screens
Elite Screens Insta-DE Series Manual de usuario
Elite Screens
Elite Screens TE100HC2 Manual de usuario
Elite Screens
Elite Screens Insta-DE 2 Series Manual de usuario
Elite Screens
Elite Screens Spectrum Series Manual de usuario
Elite Screens
Elite Screens aeonclr series Manual de usuario
Elite Screens
Elite Screens Saker Series Guía
Elite Screens
Elite Screens Elite Tripod Series Manual de usuario
Elite Screens
Elite Screens F100NWH Manual del propietario
