Elite Screens Aeonclr series Manual de usuario

Rev.071816-DR www.elitescreens.com 1

AeonCLR™ Series

EDGE FREE® Fixed Frame Screen w/ StarBrightCLR®

(Ceiling Light Rejecting) Front Projection Material

User’s Guide

Product Description:

The Aeon CLR™ Series is an ultra-short throw fixed frame projection screen that uses Elite’s EDGE FREE®

technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light

cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.

Screen Maintenance

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image.

For optimal results we advise to pay attention to the following instructions.

1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular motion.

Wipe from left to right only.

2)Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may damage the

screen’s surface).

3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.

Notes：

The following precautions should be followed at all times to avoid damaging the material, which is not

covered under warranty.

 Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.

 Don’t scratch the material,as it will leave permanent markings on the screen’s surface.

 Don’t point to the screen material with a fingertip or other sharp objectsto prevent damage to the material.

 Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such

chemicals will permanently damage the screen.

Assembly Video

Watch our assembly video on-line at

www.elitescreens.com/aeonCLR_assembly

or scan the QR code

Rev.071816-DR www.elitescreens.com 2

Hardware and Parts List

Please make sure all parts listed below are included before installation.

A. Elbow joint x 4 pcs B. Top/Bottom horizontal frame x

4 pcs

C. Left/Right vertical frame x 2 pcs D. Center joints x 2 pcs

E. Center support bar x 1-2 pcs F. Wall brackets x 2-3 pcs G. M6 screw x 2-4 pcs H. M5x15 screw x 24 pcs

I. M6x12 screw x 2-4pcs J. Screw and anchor x 6-9 pcs K. Rubber mallet x 1 pc L. Screw driver x 1 pc

M. Black Tape x 1 bag N. Bezel trim x 6 pcs O. Corner sleeve x 4 pcs P. White gloves x 2 pcs

Frame Assembly

1. Insert the center joint into one of the ½ horizontal frames and fasten it with the two M5x15 screws (H).

2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.

3. Repeat steps 1 and 2 for assembling the second horizontal frame.

Push Push

4. Insert and slide in oneM6 screws(G) through the channel located on the backof each horizontal frame (B).

Place one M6 hex screw (G) in the center for attaching the center support bar (E)

Horizontal frame

Top right Frame Top left Frame

Horizontal long frame

Face up

M6 hex screws (G)

Center joints

Rev.071816-DR www.elitescreens.com 3

5. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below.

6. Insert the two vertical short frames(C) into the elbow joint (A).

7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.

Horizontal Long frame (B)

Horizontal long frame (B)

ElbowJoint

(A)

Push

Elbow Joint

(A)

Horizontal long frame (B)

Vertical short frame(C)

push push

Push

Rev.071816-DR www.elitescreens.com 4

8. Make sure all four corners are properly in place to form a perfect square.

Then fasten the four angles with the M5x15 Screws (H).

Screen Material Installation

Please read this important note before proceeding with the installation process of the material:

Before handling the StarBright CLR® material, put on the supplied pair of white gloves to avoid leaving

fingerprint marks, dust or hand oil on the material’s surface (Figure1). The StarBright CLR® material is very

delicate and should be handled with extreme care. Do not allow the material to fold or bend. Failure to follow

instructions will result in permanent damage to the screen material, which is not covered by warranty.

1. Remove the StarBright CLR® material from the packaging tube and set it gently on a clean surface.

Tip: Carefully put a small flat weighted object at the edge (PVC/Velcro end) to prevent it from moving out of place.

Please keep the front of the materialface down.

2. It is strongly recommended for two people to unroll the material to prevent the screen from bending or rolling

unevenly. Each person holds one end of the roll and slowly unrolls the screen in a clockwise direction (Figure 2).

3. Lay the material completely flat with the front facing down on a clean surface in a horizontal position (Figure 3).

Four corners join correctly to form a perfect

rectangle. Use the included screwdriver (L)

to fasten the Mx15 screws (H) into each

corner by aligning the frame screw holes to

the holes in the elbow joint (A).

Figure 2

Back side of material

Front side of material

Horizontal positionlaid ona clean surface

Figure 3

Figure 1

Tip: Small weighted object

Rev.071816-DR

www.elitescreens.com

4. Carefully and gently

place the assembled frame

allow the angle edge of the frame to come in direct contact with the material to avoid puncturing

After all of the corners of the frame have been

following order A→B→C→D

(see instructions below for details)

Attach the screen material to the corners as shown below.

2) Fold over and

material to the Velcro

strip of the frame.

1) Stretch the screen material in

the directionof the arrowhead.

www.elitescreens.com

place the assembled frame

on top of the screen material

as shown below

allow the angle edge of the frame to come in direct contact with the material to avoid puncturing

After all of the corners of the frame have been

properly aligned (example A), attach

the material on the frame in the

(see instructions below for details)

Attach the screen material to the corners as shown below.

Screen material back facing up

2) Fold over and

attach

material to the Velcro

strip of the frame.

3) Fold over second side

and attach to frame

Repeat until all four sides

are done in the order A, B, C, D

as shown below

. Make sure to not

allow the angle edge of the frame to come in direct contact with the material to avoid puncturing

or damaging it.

the material on the frame in the

Screen material back facing up

Velcro

Repeat until all four sides

are done in the order A, B, C, D

Rev.071816-DR www.elitescreens.com 6

6. After all four corners have been attached; please check whether the screen material wraps the frame corners. If not,

please loosen the Velcro connection and repeat the above steps so the frame is not exposed.

7. Proceed to attach the rest of the material to the frame as described in the illustrations below.

Note:

Represents

thescreen

Lay the Velcro end on the screen material over the

Velcro end of the frame and keep it within the

edge.

Proceed in the following sequence ①②

Attach in the following

sequence:a-b-c-d

Note: The black shaded part

represents the Velcro on the

frame. That Velcro end will

ultimately attach with the

other Velcro end on the

screen material.

The key is to attach within the middle sections

of 1 and 2. Then continue attaching the

remaining unattached areas.

Repeat the same steps on remaining

three sides in the sequence A, B, C, D.

Grasp the middle of the screen

material and attach it to the Velcro

strip on the frame

Rev.071816-DR www.elitescreens.com 7

Screen Material Removal

Follow the steps to properly remove the screen material from the frame. This procedure will ensure prolonging the life

of the screen material.

1. Detach the Velcro from the frame.

2. Gently pull back the material to release the material from the Velcro connections on the corners

Support bar installation:

1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar with

the M6 hex screws (G) on the top and bottom frames.Then fasten with the M6x12 screws (I).

Pull back the screen material from

the Velcro connection along the

edges of the frame to detach it.

Support bar

Move the M6 hex screw (D) to the middle area of the frames.

Align the M6 screws

with the two holes.

Rev.071816-DR www.elitescreens.com 8

Edge trim Installation

Included is an black edge trim that provides an elegant ultra-thin bezel finish

1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. Align

the tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to the

center of the top and bottom of the screen material.

Figure 1

2．Without removing the adhesive tape, place all the trim pieces along the edge of screen material. Adjust the trim

pieces so that the four corners are evenly aligned. (Note: The Elite logo should be positioned on the bottom right).

Refer to Figure 2 below for a visual reference.

Figure 2

NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The back of the

material should be labeled with a DOWN sticker to indicate the material is facing in the down position. The Elite

Screens logo should be installed on the DOWN side

Plastic corner sleeve x4pcs

Edge trim x 6 PCS

Black tape x1pcs

Trim

strip

Screen Material

The black tape

Front Side

Back Side

Rev.071816-DR

www.elitescreens.com

After properly aligning all trim pieces, carefully remove trim piece

backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining

trim pieces in the following order: B

Figure 3

4. After the bezel trim has bee

n installed

the corner sleeve

through the front of the screen

bezel trim.

Once all corner sleeves have been snapped into each corner of the frame, it is ready to be

Diagonal Size Note

The Diagonal Size of the AR100H-CLR

before and after installing the

Before installing the trim strip

www.elitescreens.com

After properly aligning all trim pieces, carefully remove trim piece

(see Figure 3 below). Remove the inside

backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining

trim pieces in the following order: B

-C-D-E-F.

Figure 3

The front side

of the frame with trim pieces attached

n installed

, placea corner sleeve (O)on all four corners.

Begin by

through the front of the screen

. Make sure the corner sleeve

completely

Once all corner sleeves have been snapped into each corner of the frame, it is ready to be

wall installation

before and after installing the

edge trim strip.

Before installing the trim strip

After installing the trim

Front side

(see Figure 3 below). Remove the inside

backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining

of the frame with trim pieces attached

Begin by

aligning and adjusting

completely

wraps the edge of the

wall installation

After installing the trim

strip

Back side

Rev.071816-DR www.elitescreens.com 10

Proper Projector Placement for StarBright CLR®

The StarBright CLR® is exclusively for table-mounted ultra-short throw projectors as illustrated in example

1 below. Overhead placement or a standard projector will make the image very dark, on account of the screen’s

absorbent layer deflecting light that is not aligned with its reflective angle.

Example 1: Proper Projector Installation

Example 2: Improper Projector Installation

Otros manuales para aeonclr series

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens Kestrel Stage Series Manual de usuario

Elite Screens

Elite Screens Electric100H Manual de usuario

Elite Screens

Elite Screens VMAX Tab-Tension Dual Series Manual de usuario

Elite Screens

Elite Screens Manual SRM Pro Series Manual de usuario

Elite Screens

Elite Screens Evanesce AcousticPro UHD Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Guía de referencia rápida

Elite Screens

Elite Screens Saker Series Manual de usuario

Elite Screens

Elite Screens YardMaster 2 Series Manual de usuario

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens Edge Frame Manual de usuario

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Guía de referencia rápida

Elite Screens

Elite Screens Yard Master 2 Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens F60XWV1 Manual de usuario

Elite Screens

Elite Screens M100S Manual de usuario

Elite Screens

Elite Screens Saker Tension Series Manual de usuario

Elite Screens

Elite Screens Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens F100NWH Manual del propietario

Elite Screens

Elite Screens Elite Home 2 Series Manual de usuario

Elite Screens

Elite Screens Elite CineTension Series Manual de usuario

Elite Screens

Elite Screens Evanesce B Series Manual de usuario

Elite Screens

Elite Screens Manual Tab-Tension 2 Series Manual de usuario

Elite Screens

Elite Screens Evanesce Tension Series Manual de usuario

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación

Elite Screens aeonclr series Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas