Elite Screens Saker Tension Series Manual de usuario

051215-JA 1 www.elitescreens.com

Electric Wall/Ceiling Projection Screen

Saker Tension Series

User’s Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra

Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.

Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this

unit are prohibited and will void your warranty.

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

•The power outlet supplying power to the unit should be close to the unit and easily accessible.

•Do not install the unit on uneven or inclined surfaces.

•Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

•Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short

circuit.

•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.

No one except authorized technicians can open and make repairs to this unit.

•Make sure the power source this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid overheat.

•Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

•Avoid direct Sunshine, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from overheating.

•Cut off the power supply first before transportation or maintenance.

•Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

051215-JA 2 www.elitescreens.com

WARNING

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures.

Reorient or relocate the receiving antenna of the device which may be causing the

interference.

Increase the separation between the screen and the device’s receiver.

Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

that the fasteners used are of adequate strength and suitable for the installation location.

Hardware Parts List

Please make sure all parts listed below are included before proceeding with the installation.

A. Wall/Ceiling mount

bracket x2 B. M4x50 Screw x4 C. M10 Dry-wall

anchor x4 D. Bracket

connector x2 E. M5x15 Bolt

Screw x4

F. M5x25MM round

head cross screws x2 G. M5x30MM eyebolt

screw & M5 nut x2 H. Hidden wall

bracket x2 I. R18xR6x1 washer

x4 J. Snap link x2

051215-JA 3 www.elitescreens.com

Installation Instructions

For installation assistance, please consult a professional Installer. Elite Screens is not liable for faulty installations.

A. Wall Mount

Flush mount with wall/ceiling brackets

(fixed position)

1. Begin by sliding the bracket connector (D) all the way to each end of the housing.

2. Then attach it to the wall/ceiling mount bracket (A) with the M5x15 bolt screw (E).

3. Measure and mark the (WxH) distance between the two holes on each bracket.

4. Drill a hole for each screw hole on the marked areas.

5. Insert a dry-wall anchor (C) into the wall.

6. Insert a M4x50 Screw (B) in each dry-wall anchor (C) and screw it in leaving about 1/8” of an inch.

7. Hang the screen by aligning the end cap holes to the M4x50 screws (B).

II. Flush hidden mount

(movable position)

This mount method allows the screen to slide

horizontally

1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom

screw holes from each hidden wall mount bracket (H).

2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor (C), M4x50 screw (B), and a

washer (I). Make sure both brackets are properly leveled.

3. Hang the screen by placing the downward “catch “located on the back over the brackets upper “catch”.

4. After making sure the screen is secured, you can slide it left / right to properly center it in position.

5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.

Bracket connector

(D)

Wall/Ceilin Mount

Bracket (A)

M5x15 Bolt

Screw

M4x50

screws (b)

Wall

Dry-wall

anchors (C)

Wall

Front view of bracket (h)

Side view of

bracket (h)

051215-JA 4 www.elitescreens.com

B. Ceiling Mount

I. Flush Ceiling

Mount

1. Determine where the screen will be installed. Then, measure and mark the distance between the (WxH) locations.

2. Drill a hole on all marked areas and insert a dry-wall anchor (C).

3. Secure the screen by inserting the M4x50 screw (B) and a washer (I) thru the wall/ceiling mount brackets (A).

Two or more people are required while one holds the screen in place.

II. Suspended

1. Screw the

eyebolt

(G)

on the

bracket connector

(D).

2. Attach the snap link (J) thru the eyebolt (G) and connect it to an eyebolt screw (not included) rated for

the screen’s weight.

Screen material tension adjustment

(4mm Allen Wrench required and not included)

Remove the weight bar end cap to expose the adjustment tension knob. Insert your 4mm Allen Wrench to

push in the adjustment tension knob, turn clockwise and your screen will gain more tension. Turn the Allen

Wrench counter clockwise and the screen will lose tension. Please note this adjustment is not necessary as

the tension of the screen has been set to its factory setting for best performance. Please contact Elite Screens

for assistance to avoid damaging the screen and voiding your warranty at techsupport@elitescreens.com

Dry

wall

anchors (C)

M4x50 screw (B)

Ceiling

ush

Tension knob

Washer (I)

051215-JA 5 www.elitescreens.com

Saker Tension Series | Controls and Accessories

A. IR Remote B. RF Remote C. Wall switch control box D. 5-12 volt trigger cable

E. IR extended “eye” receiver F. Wireless 5-12v trigger cable G. AAA batteries H. Bubble leveler

Screen operation

Electric Current: The screen operates on AC110V @ 60hz

1. Plug the screen’s power cord into a power outlet.

2. Once the screens has power, you’ll be able to control it using any of the 6 methods described below.

6 ways to control your Saker Tension

IR remote control

(

Item A, Fig 1

): The Infrared

functions by direct line

of sight contact with a beam range of 30 feet. Aim the IR remote at the

circular window located on the left side of the screen.

2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs

directly into the screen’s RJ-45 input to present a low profile line-of-sight

control option for your IR remote control even in a recessed ceiling

installation.

3. RF Remote Control (Item B): The radio waves eliminate the need for a

direct line of sight with a range of 100 feet.

Fig.2

Fig.3

STOP

DOWN

IR “eye” receiver

3 Way Wall Switch

(does not have IR sensor)

Fig.1

IR/RF remote

Way Wall Switch

(

Item C, Fig 3

)

The 3

way wall switch

is a wall mount control box with an up/stop/down button and

plugs directly into the screen’s RJ-45 input.

051215-JA 6 www.elitescreens.com

St op

Down

For more information, technical support or your local Elite Screens

contact, please visit www.elitescreens.com

12 volt trigger

(Item D, Fig 4)

The built

in 5

12V trigger input allows your screen to synchronize

its drop & rise with the projector’s power cycle.

The screen deploys when the projector powers up

and will retract when the projector powers down.

The 5-12 volt RJ45 cable connects to your

projector’s trigger output via a separate cable that

may or may not be provided by the manufacturer of

the projector. The trigger feature will not work

without an output cable from the projector, but it

can be tested by connecting the Red (+) and Green

(-) cable to a 9-volt battery.

Wireless 5

12 volt trigger

(Item F, Fig 5)

The RF remote control serves as a dual purpose, independently as a

handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency

technology can be programmed to send a wireless signal to synchronize its drop & rise with the projector’s power

cycle.

Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions

Step 1: Connect the wireless 5-12 volt trigger cable to the RF remote (3.5mm)

Step 2: Connect the 12 v adaptor end of the wireless 5-12 volt trigger cable to your projector

Step 3: Make sure to unplug your screen from the power outlet

Step 4: Hold the UP button on your RF remote

Step 5: While holding the UP button, plug the screen back to the power outlet

Step 6: Wait 5 seconds and then release the UP button

Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to

control your screen with your projector’s power cycle

Repeat the steps again if not successful.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30

seconds for full off and on cycle each time)

DC 5-12V out

ireless

12V

tri er cable

The back of the

projector

Fig.4

3 pron power cord

RJ45 Input

12 volt tri er cable

Fi 5

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens EDGE FREE Aeon Series Manual de usuario

Elite Screens

Elite Screens SilverFrame 100GH1 Manual de usuario

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Manual de usuario

Elite Screens

Elite Screens VMAX 2 Series Manual de usuario

Elite Screens

Elite Screens Lunette Series Manual de usuario

Elite Screens

Elite Screens 100 series Manual de usuario

Elite Screens

Elite Screens Kestrel Home Series Manual de usuario

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Elite Screens

Elite Screens Tripod B Series Manual de usuario

Elite Screens

Elite Screens CineTension 2 Series Manual de usuario

Elite Screens

Elite Screens EDGE FREE Aeon StarBright 9 Series Manual de usuario

Elite Screens

Elite Screens Home100IWH2-A Manual de usuario

Elite Screens

Elite Screens Home100IWH3 Manual de usuario

Elite Screens

Elite Screens ezCinema Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens ezFrame Plus Series Manual de usuario

Elite Screens

Elite Screens GolfSim Bay Series Manual de usuario

Elite Screens

Elite Screens Spectrum Tension Series Manual de usuario

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Guía de referencia rápida

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

Elite Screens

Elite Screens SILVERMAX106H2 Manual de usuario

Elite Screens

Elite Screens CineTension2 Series Guía de referencia rápida

Elite Screens

Elite Screens Elite ES-M120UWV2 Manual de usuario

Elite Screens

Elite Screens Starling Tab-Tension 2 Series Guía

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación