Elite Screens Elite Home 2 Series Manual de usuario

Rev.010412-AS

www.elitescreens.com [email protected]

Electric Motorized Projection Screen

Home 2 Series

User’s Guide

Rev.010412-AS

www.elitescreens.com [email protected]

Make sure to read this user’s guide and follow the procedure below.

Caution: The Screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black

Top Drop in the roller. Please be a are of this as it ill void your arranty ith Elite Screens. Unapproved

changes or modifications (except for cutting the po er cord for hard ire installations) to this unit are

prohibited and ill void your arranty. For more information, please contact our Technical Support

Department at (877) 511-1211 Ext. 604.

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not

recommended by the manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power

source is advised.

•The power outlet supplying power to the unit should be close to the unit and easily

accessible.

•Do not install the unit on uneven or inclined surfaces.

•Do not place any heavy objects over the power cord.

•Position the power cord properly to avoid creating a trip obstacle.

•To avoid an electrical shoc or fire, due to a loose contact or short circuit, do not

overload the power cord.

•The internal & external parts of this unit are not end user serviceable. Do not attempt to

disassemble this unit by yourself. No one except authorized technicians can open and

ma e repairs to this unit.

•Ma e sure the power source that this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, ma e sure the cord has an equal rating as the

appliance to avoid over heat.

•Do not handle the power plug when your hands are wet or your feet are in contact with

water.

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind thunder or

lightning.

•Avoid direct sun light, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from

overheating.

•Cut off the power supply first before transportation or maintenance.

•To avoid possible injury and/or an electric shoc , do not attempt to use this screen if

there is obvious damage or if there are any evident bro en parts.

Important Safety & Warning Precautions

Rev.010412-AS

www.elitescreens.com [email protected]

Due to various installation environments, the instructions provided in this user’s guide are for

reference only. Please consult a professional installation company for further installation and

safety advice. The installer must insure that proper mounting hardware is used to provide

adequate strength suitable for the installation. lite Screens is not liable for any faulty

installations. For limit adjustment instructions, please contact our Technical Support

Department at (877) 511-1211 xt. 604.

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the

manufacturer. Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

owever, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures.

Reorient or relocate the receiving antenna of the device which may be casing the interference.

Increase the separation between the screen and the device’s receiver.

onnect the equipment into a different power outlet other than the device.

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with

foreign particles such as dust, sawdust, and/or liquids.

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

that the fasteners used are of adequate strength and suitable for the installation location.

Installation Warning

Pre-Installation

NOTE

Rev.010412-AS

www.elitescreens.com [email protected]

Please make sure all accessories listed below are included before proceeding.

A. B. C. D.

IR Remote RF Remote 3 Way Wall Switch IR Eye Receiver

Red+ Green-

E. F. G.

12V Trigger AAA Batteries Bubble Level

Accessories for Home 2 Series

Rev.010412-AS

www.elitescreens.com [email protected]

Please make sure all items listed below are included before proceeding with the installation.

Please consult a professional installer. Elite Screens is not liable for any faulty installations.

1. Insert each Bolt (B) through the right & left slide channel located on the top of the screen’s case.

Hardware Parts List

QTY

Screw & Dry Wall Anchor

2EA.

Bolt

Masonry Screw & Anchor

2EA.

Extruded Hanging Bracket

or 3

Hardware Parts List for Home 2 Series

120” & above x 3

brackets

Installation Instructions

Rev.010412-AS

www.elitescreens.com [email protected]

2. Slide the Extruded Hanging Bracket (D) through the rail located below the slide channel until it

meets with the top of the Bolt (B) and slightly secure the lug-nuts located on the top & bottom

of the bolt to attach the bracket.

3. Mark the installation location to drill your hole. Insert the proper screw and secure the bolts to

the bracket.

4. Example of the ome 2 installed to a wall, ceiling and enclosed.

Top hole for ceiling

installation

Back hole for all installation

Flush mount

to wall

Flush mount

ceiling

Enclosed

installation

Allow 2” of spacing

between the front and

back of the screen casing.

Rev.010412-AS

www.elitescreens.com [email protected]

For additional information, please contact Elite Screens at techsupport@elitescreens.com

1. If your screen does not move, please check the power supply. The screen will understandably

not move without power.

2. Make sure the power cord is firmly plugged to the power outlet.

3. Make sure that all cable connections are secure.

4. If the screen works well with the line switch but not with the remote control, please make sure

the remote controls have fresh batteries. Change the batteries every 6 months to ensure proper

operation of the remotes.

1. Q: Why does my screen no longer function?

A: Make sure your wall plug has power and that the screen is properly plugged. The fuse on the

screen will also need to be checked. Please contact techsupport@elitescreens.com for the

location. The tubular motor in this screen is equipped with a thermal relay. This feature will

automatically shut off the screen in the event of the motor becoming too hot. This will prevent

the motor from overheating. If you should experience this, please let the screen’s temperature

decrease for 10-15 min. before usage.

2. Q: ow is the screen material cleaned?

A: The screen material can be cleaned with mild soap and water.

3. Q: What type of batteries do the remote controls require?

A: The IR and RF remote controls use AAA alkaline batteries.

4. Q: Can you manually pull down the screen?

A: No, manually pulling down the screen will damage the electronic motor rolling system and

void your warranty.

5. Q: ow could I setup my Screens IR receiver to work with my learning remote control system

Do you have any IR codes I can use to achieve this?

A: Our IR remote controls have been evaluated and entered in to the databases of some

Universal remote control manufacturers. Please contact the manufacturer of your remote to

inquire about your remotes ability to function with ours. If they have not evaluated our remote

control then the following list of Binary codes will be used for most remote setups.

For Spectrum, VMAX2 (Plus), Home2 and CineTension 2 Series

Up: 1111 0000 0001

Stop: 1111 0000 0010

Down: 1111 0000 0100

6. Q: What is the gain on the matte white screen material?

A: The matte white material has a gain of 1.1. For detailed information, please visit

www.elitescreens.com/home2

Troubleshooting & FAQ’S

Rev.010412-AS

www.elitescreens.com [email protected]

*Measurement dimensions are intended as a reference only and subject to change ithout notice. Note: Data Error may be ±1"

Home 2 Dimension Table

Rev.010412-AS

www.elitescreens.com [email protected]

•Two (2) Year parts and labor warranty from defects in workmanship from purchase date as

follows (except for refurbished units as specified below).

•Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government,

Educational, Military, & Religious) purchases of new product only.

•Refurbished Units carry a 90-DAY parts and labor warranty.

•Each party will be responsible for one way shipping during the warranty period.

•A RMA (Return Merchandise Authorization) number must be issued in order to process a

replacement or to authorize a return for warranty repair. Elite Screens will, at its sole option

replace or repair the defective unit with a replacement *(see exceptions below) after the

defective unit or parts have been received. Once the product is received, Elite Screens will send

out a replacement *unit to the customer by ground service (subject to inventory availability).

•Do Not Return Any Unauthorized Items to Elite Screens, as they will be refused and returned

at your expense. The RMA Number must be included on the outside label of your shipping

box. Our warehouse is not authorized to accept returns without an RMA number on the

shipping label.

•RMA Numbers are valid for 45 days from the date issued.

•Missing Parts must be reported within 7 days of receipt. If reported after 7 days, the customer

will be responsible for shipping and handling fees. If reported after 30 days of receipt, the

customer will be responsible for cost of parts and shipping & handling fees.

*A New or refurbished replacement will be send out to the customer depending on the type of

purchase (new or refurbished) and based on stock availability.

North America only U.S. and anada

For Warranty and Service requests, please submit an RMA/Service Form at:

www.elitescreens.com/warrantysupportform

Please visit this link for full Warranty information:

www.elitescreens.com/warranty

For Customer Service and Technical questions, please contact Elite Screens at:

Telephone: (877) 511-1211 service@elitescreens.com

Fax: (562) 926-8433 techsupport@elitescreens.com

REMEMBER TO REGISTER YOUR PRODUCT AT:

WWW.ELITESCREENS.COM

Warranty Policy

Rev.010412-AS

www.elitescreens.com [email protected]

US & Canada Tech Support & Warranty Claim

Please contact us at ser[email protected]om or call +1 877-511-1211 #3 or fax +1-562-926-8433

Europe Tech Support & Warranty Claim

Please contact us at ser[email protected] or call +49-(0) 40-30392958

Asia Tech Support & Warranty Claim

Please contact us at ser[email protected]om.cn or call +86-(0) 755-8461-7989

Taiwan Tech Support & Warranty Claim

Please contact us at ser[email protected]om.tw or call +866+2+8990-1999

America: Europe:

Elite Screens Inc Elite Screens Europe

16410 Manning Way

Lübecker Straße 1

Cerritos, CA 90703 USA 22087 amburg, Germany

Tel: +1-877-511-1211 Tel: +49-4030392494

Fax: +1-562-926-8433 Fax: +49-40-49219200

[email protected] [email protected]

www.elitescreens.com www.elitescreens.eu

Asia:

Elite Screens France S.A.S

Elite

Screens

China

Corp.

11, Allée William Penn

Longxi

Duimianling

Industry

Zone 92150 Surenes, rance

Longcheng

Longgang

District, Tel: +33-1-45064735

ShenZhen

GuangDong,

China ax: +33-1-45064735

Tel:

+86-(0)755-8461-7989 info.fr@elitescreens.com

ax:

+86-(0)755-8461-7669 www.elitescreens.com/fr

info@elitescreens.com.cn

www.elitescreens.com.cn

Japan:

Taiwan:

Elite Screens Japan Corp.

Elite

Screens

Taiwan

Corp.

467-2-606 Tsuruma, Machida-shi,

4 ., No. 42-1 Wuguan Rd. Wugu Township Taipei Tokyo, 194-0004 Japan

County 248, Taiwan (Wugu Industrial Park) Tel: 0120-07-0008

Taiwan (R.O.C) ax: + 81(0)42-706-9130

Tel:

+886+2+8990-1999 info@elitescreens.jp

ax:

+886+2+8990+1366 www.elitescreens.jp

info@elitescreens.com.tw

www.elitscreens.com.tw

Latin America ontact:

[email protected]

East Asia ontact:

[email protected]

India ontact:

[email protected]

Contact Information

Otros manuales para Elite Home 2 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pantalla de proyección de Elite Screens

Elite Screens

Elite Screens AEON series Manual de usuario

Elite Screens

Elite Screens SILVERMAX106H2 Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens EZ-Cinema Series Guía de referencia rápida

Elite Screens

Elite Screens Saker Tab-Tension Series Manual de usuario

Elite Screens

Elite Screens Pop-Up Cinema Series Manual de usuario

Elite Screens

Elite Screens TE100HC2 Manual de usuario

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Manual de usuario

Elite Screens

Elite Screens ezFrame Plus Series Manual de usuario

Elite Screens

Elite Screens Starling 2 Series Manual de usuario

Elite Screens

Elite Screens Kestrel Series Manual de usuario

Elite Screens

Elite Screens CineTension 3 Series Manual de usuario

Elite Screens

Elite Screens VMAX2 (Plus) Series Manual de usuario

Elite Screens

Elite Screens VMAX2 (Plus) Series Manual de usuario

Elite Screens

Elite Screens Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens Elite Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens C Manual de usuario

Elite Screens

Elite Screens 100 series Manual de usuario

Elite Screens

Elite Screens Evanesce Tension B Series Manual de usuario

Elite Screens

Elite Screens Spectrum Series Manual de usuario

Elite Screens

Elite Screens Insta-DEM Screen Series Manual de usuario

Elite Screens

Elite Screens Ez-Frame Series Manual de usuario

Elite Screens

Elite Screens Kestrel Tab-Tension 2 CLR Series Manual de usuario

Elite Screens

Elite Screens Kestrel FE100H Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario

Draper

Draper Envoy Manual

SI Dynamic 2 XL Manual de usuario

Draper

Draper Nocturne+ E Instrucciones de instalación