Ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector² Trio RTX 4090 D-RGB

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced

or feel unsure about the installation procedure, please refrain from

installing the product yourself and contact our tech support for

assistance. We disclaim our liability for any damages to the product as

well as incidental, consequential, or indirect damages incurred due to

improper or inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion-inhibiting coolants is always

recommended for liquid cooling systems and mandatory for

nickel-plated water blocks!

Do not use pure distilled water!

For best results, EK recommends the use of EK-CryoFuel

coolants! To reach optimal performance, make sure to

thoroughly bleed the air out of your water block!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS - Rev 1 4

BOX CONTENTS - Rev 2 (Backplate 4080/4090) 5

WATER BLOCK DIMENSIONS 6

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 7

NICKEL PLEXI 7

PREPARING THE GRAPHICS CARD 8

REMOVING THE STOCK COOLER 8

MSI GeForce RTX 4090 Suprim X 24G 8

PREPARING THE WATER BLOCK FOR INSTALLATION 9

CUTTING AND PLACING THERMAL PADS - Rev 1 10

CUTTING AND PLACING THERMAL PADS - Rev 2 (Backplate 4080/4090) 11

APPLYING THERMAL COMPOUND 12

ATTACHING THE WATER BLOCK 12

INSTALLING THE BACKPLATE - Rev 1 14

INSTALLING THE BACKPLATE - Rev 2 (Backplate 4080/4090) 15

ATTACHING THE BACKPLATE 16

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 16

FITTINGS AND TUBING 17

CONNECTING THE D-RGB LED STRIP 17

TESTING THE LOOP 18

WARRANTY 18

SUPPORT AND SERVICE 19

SOCIAL MEDIA 19

- 4 -

Thermal Grease (1 pc)

BOX CONTENTS - Rev 1

4 mm

8 mm

10 mm

EK-Loop Multi Allen Key (1 pc)

Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

M2.5x8 AX1 Screw (1 pc)

M3x10 AX1 Screw (1 pc)

EK-Quantum Vector2Trio RTX

4090 D-RGB

M2.5x4 AX1 Screw (9 pcs)

Polyamid Washer M2.5 0.5mm (9 pcs)

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

EK-Plug Out Spludger Tool (1 pc)

Standoff M2.5-M3 x 6.6mm (1 pc)

Nut M2.5 (2 pcs)

Terminal OR - Vector

14x1 mm (2 pcs)

EAN: 106080

EAN: 106046

Thermal Pad F 1.0 mm (7 pcs)

(3830046996732)

Thermal Pad F 1.5 mm (2 pcs)

(3830046996749)

Thermal Pad G 2.0 mm (2 pcs)

(3830046996794)

120 mm

16 mm

120 mm

16 mm

120 mm

24 mm

- 5 -

Thermal Grease (1 pc)

BOX CONTENTS - Rev 2 (Backplate 4080/4090)

4 mm

8 mm

10 mm

EK-Loop Multi Allen Key (1 pc)

Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

M2.5x8 AX1 Screw (1 pc)

M3x10 AX1 Screw (1 pc)

EK-Quantum Vector2Trio RTX

4090 D-RGB

M2.5x4 AX1 Screw (9 pcs)

Polyamid Washer M2.5 0.5mm (9 pcs)

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

EK-Plug Out Spludger Tool (1 pc)

Standoff M2.5-M3 x 6.6mm (1 pc)

Nut M2.5 (2 pcs)

Terminal OR - Vector

14x1 mm (2 pcs)

EAN: 106080

EAN: 106046

Thermal Pad F 1.0 mm (5 pcs)

(3830046996732)

Thermal Pad G 2.0 mm (2 pcs)

(3830046996794)

Thermal Pad G 1.0 mm (4 pcs)

(3830046996770)

120 mm

16 mm

120 mm

24 mm

120 mm

24 mm

- 6 -

WATER BLOCK DIMENSIONS

307 mm

95.5 mm

123.5 mm

142.5 mm

133 mm

155 mm

27 mm

25.5 mm

- 7 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

- Dimensions: (L x H x W): 307 x 155 x 27 mm

- D-RGB LED count: 15

- D-RGB cable length: 50 cm

- D-RGB connector 3-pin 5V digital LED header

(Pinout: +5V | Data | Blocked | Ground)

Position EAN Description Quantity

1106062 Coldplate (Ni) 1

2106063 Top plate (Plexi) 1

3106069 LED Cover (N. Elox) 1

4103971 Stand out (Acetal) 1

5103964 Mylar sticker 2

6100663 EK - Badge 2

78208 Screw M3 x 8 7991DIN 2

8103947 FC Terminal (Acetal) 1

9104106 Terminal OR - 14 x 1 mm 2

10 104216 Disc magnet 3 x 3 2

11 103942 Terminal Badge 1

12 8311 Screw M4 x 20 DIN7984 3

13 103988 Standoff M4-M2.5 x 3 mm 4

14 103987 Standoff M3.5-M2.5 x 3 mm 4

15 103986 Standoff M3.5-M2.5 x 11.3 mm 7

16 9024 Screw M4 x 10 DIN7984 15

17 106077 Main OR - 160 x 2 mm 1

18 103962 Plexi insert 1

19 106067 Backplate (B. Elox) 1

20 104188 Standoff 4.5/2,5 8

21 104187 Screw M2.5 x 8 AX1 8

22 106081 PCB cardboard 1

23 101556 LED D-RGB strip 500/300 mm 1

16 10

- 8 -

Important! Before starting, make sure to have a clean, ﬂat

surface to work on. It is recommended to put foam or soft

material to lay the graphics card on.

REMOVING THE STOCK COOLER

MSI GeForce RTX 4090 Suprim X 24G

STEP 1

First, remove twelve (12) screws

from the backside ofthe Stockcooler

(using a Phillips head screwdriver)

and detach the backplate. After

removing the backplate, additional

(4) blue-marked screws must be

removed to detach the retention

bracket.

PREPARING THE GRAPHICS CARD

STEP 2

Five (5) screws must be removed to detach the I/O Bracket. Save the

I/O Bracket for later use.

Lastly, one (1) blue-marked screw must be removed. Unplug the

connectors and remove the stock cover from the GPU PCB.

STEP 1

STEP 2

Phillips Head Screwdriver

For this step, you will need:

Phillips Head Screwdriver

For this step, you will need:

RETENTION BRACKET

I/O BRACKET

- 9 -

Phillips Head Screwdriver

PREPARING THE WATER BLOCK FOR INSTALLATION

STEP 1

Unscrew eight (8) Screws AX1 M2.5 x 8 mm. Remove the backplate

together with the Screws and backplate standoffs. Standoffs must stay

on Screws AX1 M2.5 x 8 mm. Remove the PCB cardboard. Save the

removed parts for later steps.

Do not remove standoffs from screws! In case the

standoff detaches from the screw, replace it with a

spare one. When replacing the standoff make sure

that you screw it on the AX1 M2.5 x 8 screws. Do not

push the standoff onto the screw AX1 M2.5 x 8 mm.

STEP 1

For this step, you will need:

BACK PL AT E

M2.5 x 8 AX1

BACK PL AT E S TAN DO FF

DO NOT REMOVE

STANDOFFS

FROM SCREWS!

PCB

CARDBOARD

- 10 -

CUTTING AND PLACING THERMAL PADS - Rev 1

STEP 1

The GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

Remove the protective foil from both sides of the thermal

pad before installation.

Replacement thermal pads:

Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

Thermal Pad F 1.5 mm – (120 x 16 mm) EAN: 3830046996749

Thermal Pad G 2.0 mm – (120 x 24 mm) EAN: 3830046996794

STEP 2

Once cut to the size, Thermal Pads should be placed on the PCB, as

shown in the picture.

STEP 2

Thermal Pad - 120 x 16 x 1.0 mm

STEP 1

Thermal Pad F – 1.0 mm (120 x 16 mm)

120 mm

16 mm

1 mm

Thermal Pad F – 1.5 mm (120 x 16 mm)

1.5 mm

120 mm

16 mm

Thermal Pad G – 2.0 mm (120 x 24 mm)

120 mm

24 mm

2 mm

Otros manuales para EK-Quantum Vector2 Trio RTX 3080/90 ABP Set...

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FC1070 GTX Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb EK-FC 6970 V2 Manual

ekwb

ekwb EK-FC I750 SSD Series Manual

ekwb

ekwb EK-PRO GPU WB RTX A4090 Manual de usuario

ekwb

ekwb EK-Vector Trio RTX 2080 Manual de usuario

ekwb

ekwb EK-DBAY RES SPIN Guía

ekwb

ekwb EK-FC1080 GTX Ti TF6 Manual de usuario

ekwb

ekwb EK-MOSFET ASUS M6G Guía

ekwb

ekwb EK-XRES DCP 2.2 Reservoir Manual

ekwb

ekwb EK-FB EVGA CLASSIFIED 4-SLI Guía

ekwb

ekwb EK-Vector Radeon VII Manual de usuario

ekwb

ekwb EK-FC1080 GTX JetStream Backplate Guía

ekwb

ekwb EK-FC680 GTX FTW Guía

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Manual de usuario

ekwb

ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-FC R9-290X SE Backplate Guía

ekwb

ekwb EK-FC 6970 Manual

ekwb

ekwb EK-FC4890CF Guía

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-FC970 GTX Manual

ekwb

ekwb Classic D-RGB S240 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

Manuales populares de Hardware de computadora de otras marcas