ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manual de usuario
USER GUIDE
GPU WATER BLOCK
EK-Quantum
Vector XC3 RTX 3080/3090 D-RGB
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
REQUIRED TOOLS 5
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 8
CUTTING AND PLACING THERMAL PADS 9
APPLYING THERMAL COMPOUND 10
INSTALLING THE WATER BLOCK 11
PLACING THE BLOCK ON THE GRAPHICS CARD 11
ATTACHING THE BLOCK TO THE GRAPHICS CARD 12
ATTACHING THE I/O BRACKET 12
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 13
INSTALLATION OF FITTINGS AND TUBING 13
CONNECTING THE D-RGB LED STRIP 14
TESTING THE LOOP 14
CHECKING FOR CONTACT IN CASE OF HIGH TEMPERATURES 15
SUPPORT AND SERVICE 16
SOCIAL MEDIA 16
- 4 -
BOX CONTENTS
4 mm
4 mm
6 mm
8 mm
M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)
M2.5 Nut (2 pcs)
M2.5x6 AX1 Screw (13 pcs)
Allen Key 2.5 mm (1 pc)
Thermal Pad F 1.0 mm (4 pcs)
Thermal Grease (1 pc)
M2.5x8 AX1 Screw (2 pcs)
M2.5x4 AX1 Screw (16 pcs)
EK-Quantum Vector XC3 RTX 3080/3090 D-RGB PVC Washer M2.5 (16 pcs)
120 mm
16 mm
EK-Plug G1/4 (2 pcs)
Universal Mounting Mechanism – You may not need every
screw from this package.
- 5 -
WATER BLOCK DIMENSIONS
99 mm
95 mm
275 mm
124 mm
113 mm
124 mm
20.5 mm
Phillips Head Screwdriver Scissors
REQUIRED TOOLS
- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Technical Specification:
- Dimensions: (LxHxW) - 275 x 124 x 20.5 mm
- D-RGB (Addressable RGB) cable length: 500 mm
- D-RGB LED count: Plexi (5), Acetal (11)
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
M4 x 8 DIN7984 SCREW
M3.5/M2.5 x 12.6
STANDOFF
M4 x 27 DIN7984
SCREW
TERMINAL
(PLEXI / ACETAL)
O-RING 15x1
INSERT
COLDPLATE
(COPPER / NICKEL)
JE T P L ATE
M3.5/M2.5 x 2.5 STANDOFF
M2.5x8 AX1
SCREW
LED D-RGB
STRIP
UNDER STANDOUT
(BLACK)
EK BADGE
STANDOUT (BLACK / WHITE)
O-RING 122X2
TOP PLATE (PLEXI / ACETAL)
- 7 -
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
OPTION 1 – GPU Versions Without a Backplate
Some versions of this GPU don’t have a backplate (e.g., EVGA GeForce
RTX 3080 XC3 BLACK GAMING).
Use the Phillips head screwdriver to remove the eleven marked screws
and the Stock Cooler Backplate from the backside of the GPU. You do
not have to remove the unmarked I/O Bracket screw.
Carefully detach the PCB from the stock cooler and disconnect all
cables connecting the stock cooler to the PCB.
Always remove the stock cooler slowly - it might be firmly
glued to the PCB with thermal pads.
You will need the following tool:
Phillips Head Screwdriver
STEP 1
STOCK COOLER BACKPLATE
OPTION 1
I/O BRACKET SCREW
- 8 -
STEP 2
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
OPTION 2 – GPU Versions With a Backplate
Use the Phillips head screwdriver to remove the twelve marked screws
and the Stock Cooler Backplate from the backplate’s side.
Carefully detach the PCB from the stock cooler and the backplate, and
disconnect all cables connecting the stock cooler to the PCB.
Always remove the stock cooler slowly - it might be firmly
glued to the PCB with thermal pads.
STEP 1
OPTION 2
STOCK COOLER BACKPLATE
BAC KP L ATE
- 9 -
STEP 2
STEP 2
Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal pads:
4x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm
Thermal Pad F 1.0mm
- 10 -
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the CPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 1
APPLYING THERMAL COMPOUND
For this Step, you will need: Thermal Grease - EAN: 3830046998446
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Hardware de computadora de ekwb
ekwb
ekwb EK-FC560 GTX Manual
ekwb
ekwb EK-KIT HT Series Manual de usuario
ekwb
ekwb EK-SB ASUS M6G Guía
ekwb
ekwb EK-FC970 GTX TF5 Manual
ekwb
ekwb EK-FC 780 GTX Ti DCII Manual
ekwb
ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Manual de usuario
ekwb
ekwb EK-XRES DCP 4.0 Manual
ekwb
ekwb EK-FC980 GTX TF5 Guía
ekwb
ekwb EK-UNI RAD Manual
ekwb
ekwb EXTREME 240 Manual de usuario
ekwb
ekwb EK-Quantum Momentum ROG Crosshair VIII Hero Manual de usuario
ekwb
ekwb EK-Vector FTW3 RTX 2080 Ti Guía
ekwb
ekwb Supremacy EVO Manual de usuario
ekwb
ekwb EK-FC5x0 GW GTX water block Manual
ekwb
ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario
ekwb
ekwb EK-FC R9-285 Manual
ekwb
ekwb EK-XLC PREDATOR 240 Manual de usuario
ekwb
ekwb EK-Quantum Magnitude sTRX4 Manual de usuario
ekwb
ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Manual
ekwb
ekwb EK-FC590 GTX Guía
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
