ekwb EK-FC560 GTX Manual
All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18th of April, 2011.
Installation and mounting manual for EK-FC560 GTX water block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION. Sample picture of Nvidia 560 GTX Ti graphics card
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER: Remove encircled screw
on the I/O bracket:
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD
1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly
screws and backplate should be removed. There are 14 screws on the back of the graphics
card.
2. CLEANING THE PCB. Carefully detach the original heat sink after removing all
fasteners securing it to the board and bracket. Wipe off the remains (by using
non–abrasive cloth or Q-tip, as shown on sample photo) of the original thermal
compound until the components and circuit board are completely clean. EKWB
does not recommend using any liquids for removing paste.
3. APPLYING THERMAL COMPOUND. Apply thermal compound: lightly
coat the GPU with for example Arctic Cooling MX-2 ™or MX-4 ™ thermal
grease. EKWB recommends to apply thermal grease in cross form for best
performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which may
already be pre-cut. Others have to be cut to smaller chunks in order to cover all the VRM
components and PCIE lane splitter chip (PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL
PADS PRIOR TO INSTALLATION. WARNING: DIMENSION BELLOW ARE SCALED).
STEP 3: INSTALLING WATER BLOCK
PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than enough pads to
cover all surfaces that need to be covered to make block fully functional). It is advised to use small drops of electrically non-conductive thermal grease on chips to make thermal
pads more adhesive and also to improve heat transfer.
1
1
1
2
1
2
2
1
1
1
1
2
1
1
1
1
1
All pads are 1mm thick.
All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18th of April, 2011.
3. PLACING STANDOFFS ON BLOCK. Standoffs are obligatory to make this block fully
functional. Please use small amount of thermal grease on standoffs and glue them so they
are concentric with mounting holes. Once they are stuck to block be careful not to move
them.
4. PLACING BLOCK TO GRAPHIC CARD. During this process please make sure
you align holes on PCB with holes on block. Also pay attention not to use too
much force by pressing block down to PCB. Chip dies are prone to cracking.
5. ATTACHING BLOCK TO GRAPHIC CARD. By using Philips screwdriver first
screw in seven (7) enclosed M3x8 screws. Please use the enclosed plastic
washers with these screws.
STEP 4: CHECKING FOR CONTACTS
Temporarily r
emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat
substeps in previous section to reattach the block. In case you fail to obtain good contact, please check again your thermal pad thickness or contact our support
service.
STEP 5: SECURING I/O BRACKET
STEP 6: FITTING POSITIONING
Use one M3x8 screw, one PVC washer and one M3 nut to secure the I/O (also known
as PCI) bracket firmly to the circuit board. This will allow the computer chassis to carry
the weight of the waterblock thus reducing the tension on the PCI-express slot.
Tighten the screw with Philips screwdriver while holding the M3 nut with your thumbs
firmly.
Screw in the fittings and plugs. Use 6mm Allen key to screw in and tighten the EK-Plug
G1/4. If you are using the fittings with threads longer than 5mm please use the 3mm
G1/4 spacer. Attach the liquid cooling tubes and connect the water-block(s) into the
cooling circuit. EKWB recommends using EK-PSC fittings with the EK-FC series water
blocks. To ensure that the tubes are securely attached to the barb/fittings, please use
hose clamps or an appropriate substitute. The use of an algaecide is always
recommended for any liquid cooling system.
You can use any opening as an inlet/outlet port.
STEP 6: INSERTING CARD IN YOUR PC CASE
Carefully lift your card with installed block and insert it in your PC case. Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to
bend it or cause any other unneeded moves that might damage your card or block during installation.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver 8× screws M3x8 DIN7985 8 ×Polyamid washers 1 ×M3 nut
Standoff key
Standoff
M3x8 DIN7985 screws
Polyamid washer
Placing the standoffs:
Fitting with o-ring
Spacer
O-ring
EK-PSC Fitting
M3x8 screw
PVC washer
M3 nut
Otros manuales de Hardware de computadora de ekwb
ekwb
ekwb EK-Quantum Vector FTW3 RTX 3070 Manual de usuario
ekwb
ekwb EK-FC R9-390X TF5 Series Manual
ekwb
ekwb EK-FB MSI X370 XPower Monoblock Manual de usuario
ekwb
ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manual de usuario
ekwb
ekwb EK-Momentum ROG Strix Z390I RGB Manual de usuario
ekwb
ekwb MSI MPG X570S Carbon EK X Manual de usuario
ekwb
ekwb EK-FC980 GTX Ti XG Manual de usuario
ekwb
ekwb 3831109816202 Guía
ekwb
ekwb EK-FC1080 GTX FTW2 Manual de usuario
ekwb
ekwb EK X Series Manual de usuario
ekwb
ekwb EK-Supremacy Elite Edition series Manual de usuario
ekwb
ekwb EK-UNI Manual
ekwb
ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario
ekwb
ekwb Velocity Manual de usuario
ekwb
ekwb EK-FC980 GTX Guía
ekwb
ekwb EK-FC 780 GTX Classy Manual
ekwb
ekwb EK-Quantum Velocity 2 D-RGB AM4 Manual de usuario
ekwb
ekwb EK-FC980 GTX Classy Manual
ekwb
ekwb EK-Vector Radeon VII Backplate Manual de usuario
ekwb
ekwb EK-FC970 GTX TF5 TFX Series Manual
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
