Ekwb Supremacy EVO Manual de usuario

Supremacy EVO

7th revision, Mar 4th 2016

USER GUIDE

/ 3 /

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY

This CPU liquid cooling unit is

pre-assembled for use with modern

Intel desktop socket type mother-

boards. By default (out of the box)

this water block supports the follow-

ing CPU sockets:

- Intel® Socket LGA-115x

- Intel® Socket LGA-2011(-3)

This product is also fully compatible with Intel® LGA-775, LGA-1366 and

AMD® AMx/FMx sockets however the required backplates and/or AMD

mounting plate is not included in the box. The aforementioned parts are avail-

able free of charge from EK Webshop and Partner Reseller Network.

/ 4 /

- EK-Supremacy EVO universal CPU

water block.

- PreciseMount EVO universal CPU

mounting mechanism:

• M4 threaded thumb screws (4 pcs)

• LGA-2011 M4 threaded mounting

studs (4 pcs)

• Springs (4 pcs)

• M4 threaded thumb nuts (4 pcs)

• Washers (4 pcs)

- EK-Supremacy Backplate

• Backplate rubber gasket

• Backplate for Intel® LGA-115x

socket motherboards

- Allen (hex) key 2.5mm

- Additional Inserts and Jet plates:

• Jet J2 (0.3mm thick)

• Jet J3 (0.1mm thick)

• Insert I2

- Thermal grease

The following items are enclosed with each EK-Supremacy EVO water block:

Narrow server type LGA-2011 is not supported by default – a Mounting plate

Supremacy LGA-2011 Narrow ILM (EAN: 3830046990600) is mandatory

to install this water block on narrow server type LGA-2011 motherboards. Re-

placing the mounting plate requires disassembly of the water block.

WHAT IS ENCLOSED

/ 5 /

STEP 1

Please observe the table below to

determine the optimal combina-

tion of insert and jet plate for your

type of socket:

Socket Optimal

Insert

Optimal

Jet

AMD®

AMx / FMx I2 J2

LGA-7 75 I1 J2

LGA-115x I1 J2

LGA-1366 I1 J1

LGA-2011 I1 J1

LGA-2011(-3) I2 J3

STEP 1

I1 J1

d=0,25 mm

d=0,30 mm

d=0,10 mm

REPLACING THE JET PLATE /INSERT PROCEDURE (OPTIONAL)

Water block top

Insert pin

Insert

Jet plate

Gasket

Mounting plate

Copper base

Screws

/ 6 /

STEP 2

Unscrew the four M4 screws in counter-clock-

wise direction from the bottom of the water

block using enclosed 2,5mm Allen key to re-

lease the assembly, consisting of water block

top, the insert, insert pin and jet plate. Upon re-

placing the insert and/or jet plate please re-as-

semble the water block as shown on the photo

in STEP 1 and STEP 2. Pay special attention

to the insert orientation relative to the copper

base and water block top!

Before re-assembly of the water

block it is crucial that the pre-formed

gasket (o-ring) is placed into the

gap between the mounting plate

and the water block top.

Screw the four screws back in but don’t exag-

gerate with the force applied.

STEP 2

Insert pin

Jet plate

Insert

/ 7 /

INSTALLING THE WATER BLOCK

LGA-2011(-3) SOCKET

MOTHERBOARDS

STEP 1

Prepare the foil bag with mounting mecha-

nism, which is enclosed with the CPU water

block delivery.

Install four (4) speciﬁc LGA-2011 M4 thumb

screws into four M4 threaded stubs on the

LGA-2011 socket integrated latch mecha-

nism (ILM). The screws are to be installed

using no tools (i.e. pliers).

It is recommended to remove the

motherboard form the PC chassis

before proceeding with installation

of the CPU water block because

of the space constraint limitations

of various computer cases.

STEP 1

LGA-2011

M4 Thumb

Screw

LGA-2011 M4 Thumb Screw

/ 8 /

STEP 2

Cleaning the CPU: Wipe the CPU’s

contact surface (by using non–abra-

sive cloth or Q-tip, as shown on sam-

ple photo).

Applying thermal compound: EK

recommends blob or line method of

applying the enclosed thermal com-

pound to the CPU heat spreader (IHS)

- see sample photo on right.

The quantity of about two

rice grains is just about right.

There is no need to cover

the whole IHS. Applying too

much thermal grease will

have negative impact on the

cooling performance!

STEP 2

Non-abrasive

cloth

Thermal grease

IHS

/ 9 /

STEP 3

Thumb nut

Coiled

spring

STEP 3.:

Align the water block over the

mounting screws on the LGA-

2011(-3) motherboard with pre-

installed CPU.

Before proceeding with the

installation It is mandatory

to remove the protective

foil from the backside of

the water block.

Place an enclosed compression

spring and thumb nut over each M4

thumb screw. Start fastening two

thumb nuts at a time, preferably in

cross pattern and do not tighten

them fully until all of them are partially

screwed in. Then - using your ﬁngers

only - screw in all four thumb nuts

until you reach the end of the thread.

/ 10 /

STEP 4.:

Tighten the ﬁtting barbs in clockwise

direction until the gasket underneath

is compressed.

The installation of the CPU water

block is now complete.

With EK-Supremacy EVO series water blocks it is mandatory to use the

port that is nearest to the center of the water block as INLET port. Mixing the

ports may result in less than ideal thermal performance of the water block.

STEP 4

Fitting Barb

Fitting Ring

Inlet port

Outlet port

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manual de usuario

ekwb

ekwb EK-Vector RTX 2080 FTW3 Manual de usuario

ekwb

ekwb EK-FB ASUS R5-E10 Guía

ekwb

ekwb EK-FC460 GS/SONIC Manual

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manual de usuario

ekwb

ekwb 3831109831335 Guía

ekwb

ekwb EK-FB MSI Z270 GAMING Monoblock Manual

ekwb

ekwb EK-FB KIT ASUS R5-E10 Guía

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-FB ASUS X58 Guía

ekwb

ekwb EK-FC980 GTX Ti Strix Series Manual

ekwb

ekwb EK-FC R9 Fury X Guía

ekwb

ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manual de usuario

ekwb

ekwb EK-FB ASUS M8I Monoblock Manual de usuario

ekwb

ekwb EK-FC750 GTX Series Manual de usuario

ekwb

ekwb EK-Classic AM4 D-RGB Manual de usuario

ekwb

ekwb EK-FC Titan XXL Manual

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manual de usuario

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Manual de usuario

ekwb

ekwb EK-FC980 GTX Ti TF5 Series Manual

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manual de usuario

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario

ekwb

ekwb EK-FC680 GTX SOC water block Guía

ekwb

ekwb EK-FC4890LT Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb Supremacy EVO Manual de usuario

Manuales populares de Hardware de computadora de otras marcas