Ekwb EK-FB MSI X370 XPower Monoblock Manual de usuario

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on June 1st 2017

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of MSI X370 XPower motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 1: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 4 screws on the

back of the motherboard that need to be removed in order to remove the factory

installed MOSFET cooling solution. Additional 4 screws need to be removed to remove

the plastic I/O. Please store the removed material away for later use.

Removing of the original plastic hold-down clamps and the factory backplate:

Using Philips-head screwdriver remove the four UNC 6-32 screws securing the original

plastic hold-down clamps around the socket as shown on the sketch. Remove the

original AMD® backplate and the hold-down clamps and store them away.

1. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be

trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s

circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]

2. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on PCB as

shown on the picture

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS

PRIOR TO INSTALLATION!

Installation manual for EK-FB MSI X370 XPower Monoblock water block

AMD X370

chipset

CPU socket

Mosfets

1. Thermal pad F–1.0mm

(for mosfets):

Place 1,0mm thermal pads in larger

strips over marked area and make

sure all mosfet chips and the inductor

coils (chokes) are covered.

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on June 1st 2017

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PLACING THE BLOCK ON TO THE MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo on right with enclosed EK-TIM Ectotherm thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

Install four (4) M2.5 self adhesive PVC washers under marked standoffs as shown on

the picture below.

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB MSI X370 XPower

Monoblock series water block gently to the motherboard or vice versa (as shown on

picture below). Make sure that mounting holes are aligned.

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use four M2,5x5 AX1 screws. Tighten the screws evenly. Do not

use excessive force when tightening the screws!

B) CPU part: Use four M3x10 DIN7984 screws with backplate and protective pad.

Tighten the screws using enclosed 2mm allen key.

Use the enclosed screws and backplate as shown on picture below:

STEP 5: CONNECTING THE RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock RGB LED strip to the motherboard. Please

ensure that the arrow indicated on the connector is plugged into the 12V line as

indicated on your motherboard. Failure to do so will damage your motherboard or

LED strip.

For the EK-FB MSI X370 XPower Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET

PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-

ACF series please use hose clamps or appropriate substitute to secure the tubing to

the barb. The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

AM4 backplate

insulator

M2.5 PVC Washer

M2.5x5 screws

M3x10 screws

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

AM4 backplate

Place the M2,5 self adhesive PVC washers under marked standoffs!

Este manual sirve para los siguientes modelos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FB ASUS M6E Guía

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Manual de usuario

ekwb

ekwb EK-Vector Radeon VII Backplate Manual de usuario

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb D-RGB Manual de usuario

ekwb

ekwb EK-Nucleus AIO CR360 Vision D-RGB Manual de usuario

ekwb

ekwb EK-FC 770 GTX DCII Manual

ekwb

ekwb Velocity - Intel Manual de usuario

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manual de usuario

ekwb

ekwb EK-FB EVGA X58 CLASSIFIED Manual de usuario

ekwb

ekwb EK-FB KIT EVGA SR-X Manual de instrucciones de instalación

ekwb

ekwb EK-FCQK6000 Guía

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Manual

ekwb

ekwb EK-Supremacy Classic RGB Manual de usuario

ekwb

ekwb EK-FB ASUS M5E Guía

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Manual de usuario

ekwb

ekwb EK-FB ASUS PRIME X299 RGB Monoblock Manual de usuario

ekwb

ekwb EK-Pro RTX A5000 Manual de usuario

ekwb

ekwb EK-Momentum MSI Z390 MEG GODLIKE Manual de usuario

ekwb

ekwb EK-DBAY DCP 2.2 Manual

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manual de usuario

ekwb

ekwb EK-Annihilator Series Manual de usuario

ekwb

ekwb EK-FC Terminal Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB MSI X370 XPower Monoblock Manual de usuario

Manuales populares de Hardware de computadora de otras marcas