Edimax ER-5397P Manual de usuario

IEEE 802.3

ER-5397P

User’s Manual

16-Port UTP +1-Port BNC

10Mbps Hub

FCC WARNING

This equipment has been tested and found to comply with the limits for a

Class B Digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna

 Increase the separation between the equipment and receiver

 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

 Consult the dealer or an experienced radio/TV technician for help

You are cautioned that changes or modifications not expressly approved by

the party responsible for compliance could void your authority to operate

the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

- 1 -

Packing List

The package should contain the following items:

• One Ethernet Hub

• One Power Adapter

• User’s Manual

If any of the items are missing or damaged, please contact your local dealer.

Introduction

Congratulations on purchasing our high-performance 10Mbps Ethernet Hub.

Featuring ease of installation, this hub helps hook your PCs together at a

minute, communicating instantly over the net to share resources and printers.

With sixteen UTP ports and one BNC port located at the rear panel, this

device allows you to network up to at least seventeen workstations in a

standalone configuration. An uplink function is designed for connection to

another hub to extend your segment, rather than a normal port for a

workstation. For more details about Uplink function, refer to the following

section.

Running at 10Mbps with great stability, this hub complies with IEEE802.3

standard.

Features and Specifications

Features



IEEE 802.3 compliant (10Mbps, CSMA/CD)



Provide one slide switch to select Port 1 to uplink mode or normal mode



Provide one BNC port for thin Ethernet (10Base2)



Port auto-partitioning and reconnection to facilitate faulty segment

isolation



Data collision and jabber handling functions

- 2 -

Specifications



Standards: IEEE 802.3



10Mbps Ports: RJ-45 x 16 + BNC x 1



Hub LEDs: Power, Collision



Port LEDs: Link and Activity



Dimension: 1.18 x 11.4 x 3.94 in. (30 x 290 x 100 mm)



Weight: 0.97lb. (440g)



Power: External power adapter, 12VDC, 0.5A



Operating Temperature: 32-131°F (0-55°C)



Operating Humidity: 10-95% (Noncondensing)



Emission: FCC Class B, CE Mark, C-tick

Physical Description

Front and Rear Panel

- 3 -

Left side Panel

1. Power Indicator

This LED indicator is on when the hub is powered up.

2. Collision Indicator

This LED indicator blinks when the hub detects a collision on the

network.

3. Link/Activity Indicator

These LEDs indicate the state of the data link. When the connection is

okay, these LEDs remain on. Blinking indicates data is being received

on the segment.

4. RJ-45 Ports

The hub is equipped with 16 RJ-45 ports for making 10BASE-T

hub-to-workstation connections.

5. BNC Port

Provide one BNC port for thin Ethernet (10Base2).

6. Slide switch

Port 1 is designed to provide normal or uplink function through the use

of a slide switch.

7. DC Adapter Port

Insert the power jack into this port.

- 4 -

Installation

1. Operating Environment

This hub must be installed and operated within limits of specified operating

temperature and humidity. Do not place objects on top of the unit or obstruct

any vents at the sides of the hub. Do not position the hub near any heating

source such as heaters, radiators, or direct exposure to sun. Prevent entering

of water and moisture into the unit. If necessary, use dehumidifier to reduce

humidity.

2. Connecting to network devices

Connect one end of the network cable to any of the RJ-45 or BNC connectors

on the rear panel, and connect the other end of the network cable to the

network device with RJ-45 or BNC connector and the maximum length

between the hub and any network devices UTP is 100 meters (300ft) and

BNC is 200 meters (650ft). Once the network cable is connected on both ends

and the attached network devices are powered on, the Link Status LED

should be lit.

3. Uplink to Another Hub

The Uplink function is designed to extend your segment by connecting to

another hub (see the figure below). Note that the Ethernet Hub’s port 1 can be

switched to an uplink function by switching the sliding switch. There are two

ways for you to connect to another hub:

1) Switch the sliding switch to the uplink mode to convert port 1 to an

uplink and use a straight-through twisted-pair cable to connect port 1 to

another hub.

2) If you use a crossover cable to connect the two Hubs, then you can use

any port on the Ethernet Hub to connect to any normal port on the other

Hub. Please note: the uplink port must be in normal mode for the method

to work.

- 5 -

4. Connecting the power

Plug the power cable into the hub, and connect it to an electrical outlet.

Trouble-shooting

1. Power LED is not lit

 Check if the power adapter is properly connected to the power outlet.

Make sure the DC power jack is firmly plugged into the power socket of

the hub.

2. Link Status LED is not lit

 Check the power switch of the network devices attached to the hub; make

sure they are turned ON.

 Check the network cables; make sure they are properly connected to the

hub and the network devices.

 Check the network cables; make sure the cables comply with EIA/TIA

568 specification. Use straight-through Category 3 or higher cables for

10Mbps connection.

3. Link Status LED is not lit when it is uplinked to another hub

 Check the network cable, and make sure it is properly connected to both

hubs. One end of the cable should be connected to uplink port while the

other end of the cable should connect to a regular port. Do not connect

- 6 -

the cable to both uplink ports.

 Check the network cable, and make sure the cable complies with EIA/TIA

568 specification. Use Category 3 or higher cables for 10Mbps hub

connection.

4. Collision LED flashes constantly

 Remove all the network cables; connect the cables back one by one to

isolate the source of the collision.

 Check the network cable, inferior cable quality will result in excessive

collision and error packets.

[!] Contact your dealer if problem persists.

Tabla de contenidos

Otros manuales de Cambiar de Edimax

Edimax

Edimax SP-1101W Manual de usuario

Edimax

Edimax EK-UA2C Manual de usuario

Edimax

Edimax ES-3116P Manual de usuario

Edimax

Edimax GS-1016 Manual de usuario

Edimax

Edimax ES-1008PH Manual de usuario

Edimax

Edimax GS-1016 Manual de usuario

Edimax

Edimax ES-516G+ Manual de usuario

Edimax

Edimax GS-1008P Manual de usuario

Edimax

Edimax EK-PA2C Manual de usuario

Edimax

Edimax ES-3105P Manual de usuario

Edimax

Edimax GS-1008PH Manual de usuario

Edimax

Edimax GS-5008E Manual de usuario

Edimax

Edimax ES-1016 Manual de usuario

Edimax

Edimax ES-5824PHG Manual de usuario

Edimax

Edimax ES-5424P Manual de usuario

Edimax

Edimax ES-1024 Manual de usuario

Edimax

Edimax EK-08RE Guía de referencia

Edimax

Edimax ES-5160G V2 Manual de usuario

Edimax

Edimax ES-5808PHG Manual de usuario

Edimax

Edimax ES-5824PH Manual de usuario

Edimax

Edimax GS-5424PLG Guía de configuración

Edimax

Edimax ES-5500G V2 Manual de usuario

Edimax

Edimax EK-PAK2 Guía de referencia

Edimax

Edimax ES-5160G+ Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario