Edimax ES-5500G V2 Manual de usuario

ES-5500G V2 / ES-5800G V2

Quick Installation Guide

07-2012 / v1.0

publication may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission from Edimax Technology Co.,

Ltd.

Edimax Technology Co., Ltd. makes no representations or warranties, either

expressed or implied, with respect to the contents hereof and specifically

disclaims any warranties, merchantability, or fitness for any particular purpose.

Edimax Technology Co., Ltd. reserves the right to revise this publication and to

make changes from time to time in the contents hereof without the obligation to

notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly

different from those shown in this QIG. The specification is subject to change

without notice. Please visit our web site www.edimax.com for the update. All

brand and product names mentioned in this manual are trademarks and/or

registered trademarks of their respective holders.

Edimax Technology Co., Ltd.

Add: No. 3, Wu‐Chuan 3rd Rd., Wu‐Ku Industrial Park, New Taipei City, Taiwan

Tel: +886‐2‐77396888

Email: sales@edimax.com.tw

PRODUCT INTRODUCTION

Model no.:

ES-5500G V2: 5-Port Gigabit Desktop Switch

ES-5800G V2: 8-Port Gigabit Desktop Switch

Package Contents

Before you start using this router, please check if there is anything missing in the

package, and contact your dealer to claim the missing item(s):

Gigabit Desktop switch (1 pcs)

User manual guide (1 pcs)

Power Adapter (1 pcs)

Front Panel

Please refer to the following description for the front panel:

ES-5500G V2

ES-5800G V2

LED Definition:

LED Name

Light

Status

Description

PWR

Switch on and correctly powered

Off

Switch not powered or not correctly powered

LNK/ACT

The port connected

Off

The port not connected

Flashing

The port is activating and transferring /receiving

data.

Back Panel

ES-5500G V2

ES-5800G V2

1. Operating Environment

This switching hub must be installed and operated within the limits of

specified operating temperature 0~40°C(32~104°F) and humidity (10~90%

Non-condensing).

˙Do not place objects on top of the unit.

˙Do not obstruct any vents at the sides of the unit.

˙Do not position the unit near any heating source such as heater, radiator or

direct exposure to sun.

Prevent entering of water and moisture into the unit, If necessary, use

dehumidifier to reduce humidity.

2. Connecting to network devices

The RJ-45 ports on the switch support Auto-MDI/MDI-X function which allows

using straight-thought crow-over type cables to connect this switch to

workstation or hub.

Connect on end of the network cable to the RJ-45 port on the rear panel, and

connect the other end of the network cable to the RJ-45 port on the network

device. Follow the same procedure to connect all the RJ-45 ports of the switch.

The UTP network cables must comply with EIA/TIA 568 specifications and

Category 5 standard for data transmission. Maximum length using UTP cable,

between the switch and connected devices is 100 meters (300ft).

Once the network cable is connected to both ends and the attached network

device is powered on, the green LNK/ACT LED should be lit.

3. Connecting the power

Connect the power adapter to the power connector of the unit; the green Power

LED on the front panel should be lit.

Trouble Shooting

1. Power LED is not lit

Check if the power cord is properly connected to the external power adapter

and the power outlet. Make sure the DC power jack is firmly plugged into the

power socket of the switch.

2. Link/Activity is not lit when connect to devices

˙Check the power switch of the network device attached to the switch; make

sure it is turned ON.

˙Check the network cable; make sure it is properly connected to the switch

and the network device.

˙Check the network cable; make sure the UTP cable comply with EIA/TIA 568

and Category 5 specification.

[!] Contact your dealer if problem persist.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction

with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the authority to operate equipment.

CE Mark Warning

This is a class B product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Edimax

Edimax

Edimax EK-PAK2 Manual de usuario

Edimax

Edimax ES-1024 Manual de usuario

Edimax

Edimax ES-3208P Manual de usuario

Edimax

Edimax ES-5824PH Manual de usuario

Edimax

Edimax ES-1016 Manual de usuario

Edimax

Edimax Rackmount Fast Ethernet Switch Manual de usuario

Edimax

Edimax ES-5500M V2 Manual de usuario

Edimax

Edimax EK-UAK2 Guía de referencia

Edimax

Edimax ES-1008P Manual de usuario

Edimax

Edimax ES-3316P Manual de usuario

Edimax

Edimax GS-3008P Manual de usuario

Edimax

Edimax ES-5224RS+ Manual de usuario

Edimax

Edimax USBH-004 Manual de usuario

Edimax

Edimax SP-1101W Manual de usuario

Edimax

Edimax ES-5844P Manual de usuario

Edimax

Edimax EK-08RO Manual de usuario

Edimax

Edimax Two-console 16 port PS/2 KVM Switch Manual de usuario

Edimax

Edimax EK-2U2C Manual de usuario

Edimax

Edimax ES-516G+ Manual de usuario

Edimax

Edimax ES-3308P Manual de usuario

Edimax

Edimax HP-5101ES Manual de usuario

Edimax

Edimax 9-Port Desktop Ethernet Hub ER-5390S Manual de usuario

Edimax

Edimax EU-PC2C Manual de usuario

Edimax

Edimax GS-5008E Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario