Dynojet Power commander V Manual de usuario
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 1
PARTS LIST
1 Power Commander
1 USB Cable
1 CD-ROM
1 Installation Guide
2 Power Commander Decals
2 Dynojet Decals
2 Velcro
1 Alcohol swab
1 O2 Optimizer
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2009-2010 Yamaha XT660R
Installation Instructions
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 2
EXPANSION PORTS 1 & 2
Optional Accessories such as
Color LCD unit or Auto tune kit.
POWER COMMANDER V
INPUT ACCESSORY GUIDE
Map - The PCV has the ability to hold 2 different
base maps. You can switch on the fly
between these two base maps when you hook
up a switch to the MAP inputs. You can use
any open/close type switch. The polarity of
the wires is not important. When using the
Autotune kit one position will hold a base map
and the other position will let you activate the
learning mode. When the switch is “CLOSED”
Autotune will be activated.
Shifter- These inputs are for use with the Dynojet
quickshifter. Insert the wires from the Dynojet
quickshifter into the SHIFTER inputs. The
polarity of the wires is not important.
Speed- If your application has a speed sensor then
you can tap into the signal side of the sensor
and run a wire into this input. This will allow
you to calculate gear position in the Control
Center Software. Once gear position is setup
you can alter your map based on gear position
and setup gear dependent kill times when
using a quickshifter.
Analog- This input is for a 0-5v signal such as
engine temp, boost, etc. Once this input
is established you can alter your fuel curve
based on this input in the control center
software.
Crank- Do NOT connect anything to this port unless
instructed to do so by Dynojet. It is used to
transfer crank trigger data from one module to
another.
ACCESSORY INPUTS
Wire connections:
To input wires into the PCV first remove the rubber
plug on the backside of the unit and loosen the
screw for the corresponding input. Using a 22-24
gauge wire strip about 10mm from its end. Push the
wire into the hole of the PCV until is stops and then
tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make
inserting them easier.
CRANK
ANALOG
SPEED
MAP
MAP
SHIFTER
SHIFTER
USB CONNECTION
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 3
1 Remove the seat.
2 Remove the fuel tank.
3 Install the PCV in the tail section of the motorcycle (Fig. A). Use the supplied
velcro to secure the PCV in place.
4 Attach the ground wire of the PCV to the negative side of the battery (Fig. B).
5 Route the PCV harness to the left side of the bike and go towards the throttle
bodies.
6 Locate the Crank Position Sensor connector under the left hand side cover.
Unplug this connector (Fig. C).
This is the WHITE 2 pin connector.
FIG.A
FIG.C
FIG.B
Ground
Unplug TPS
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 4
7 Plug the WHITE 2 pin connectors from the PCV in-line of the stock Crank
Position Sensor connectors (Fig. D).,
FIG.D
8 Unplug the stock wiring harness from the injector (Fig. E).
FIG.E
9 Plug the PCV in-line of the stock injector and wiring harness (Fig. F).
FIG.F
Unplug
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 5
10 Locate the Throttle Position Sensor on the right side of the throttle body.
Unplug the stock wiring harness from the TPS (Fig. G).
FIG.G
Unplug TPS
11 Plug the PCV harness in-line of the stock TPS and stock wiring harness
(Fig. H).
FIG.H
12 Locate the O2 sensor connection. Unplug this connection (Fig. J)
Follow the wires from the exhaust up to this location.
FIG.J
Unplug O2
22-020 www.powercommander.com 09-10 Yamaha XT660R PCV - 6
13 Plug the Dynojet O2 Optimizer in-line of the stock O2 sensor and wiring
harness (Fig.K).
14 Secure the O2 Optimizer in place using a zip tie.
The O2 optimizer for this model controls the stock closed loop area. This
area is represented by the highlighted cells shown in Figure L. The optimizer
is designed to achieve a target AFR of 13.6:1. To use this optimizer you must
retain your stock O2 sensor.
It is not recommended to alter the values in the highlighted area unless
instructed to do so by a Dynojet technician.
If using the Auto tune system do NOT input values in this area in your Target
AFR table.
FIG.K
FIG.L
O2 Optimizer
Otros manuales para Power commander V
95
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Dynojet
Dynojet
Dynojet Power Commander III Manual de usuario
Dynojet
Dynojet Power commander V Manual de servicio
Dynojet
Dynojet POWER VISION PV3-25-09 Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de servicio
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet PV3-25-05 Manual de usuario
Dynojet
Dynojet Power Vision Manual de usuario
Dynojet
Dynojet POWER VISION PV3-17-02 Manual de usuario
Dynojet
Dynojet Auto Tune Manual de usuario
Dynojet
Dynojet Power Vision Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet POWER VISION PV3-16-03 Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power commander V Manual de usuario
Dynojet
Dynojet Power Commander III USB Manual de usuario
