Dormakaba YD30D Manual

Installation & Operating Instructions

YD30D

Double Sideload Lock

Table of Contents

1. Document Information 3

1.1 Contents and Purpose 3

1.2 Target Group 3

2. Safety and Compliance 4

2.1 Safety Information 4

2.2 Regulatory Compliance Information 5

3. Product Information 7

3.1 Product Description 7

3.2 Package Contents 8

3.3 Technical Data 9

4. Product Dimensions 10

4.1 Lock Dimensions 10

4.2 Strike Dimensions 11

4.3 Housing Dimensions (Available Separately) 12

4.4 Dress Plate Dimensions (Available Separately) 12

4.5 Fitting Tab Dimensions (Available Separately) 13

5. Pre-Installation Assessment 14

5.1 Mounting Assessment 14

5.2 Wiring Assessment 15

5.3 Operating Mode Assessment 15

6. Mounting 16

6.1 Mortise Installation (Solid Wood) 16

6.2 Mortise Installation (Metal Extrusion) 17

6.3 Surface Mounting Installation (Solid Wood) 18

6.4 Surface Mounting Installation (Glass) 19

7. Wiring 20

7.1 Wiring Guide 20

7.2 Fail Safe Connection 20

7.3 Fail Secure Connection 20

8. Operating Mode 21

8.1 Fail Safe Operation 21

8.2 Fail Secure Operation 21

9. Maintenance 22

9.1 Maintenance and Cleaning 22

9.2 End of Service Life 22

1.1 Contents and Purpose

This document describes installation, connection, operation, and maintenance of the lock SL30DBL. Read the

document carefully and observe the instructions it contains. They contain important information for reliable

installation and trouble-free operation.

1.2 Target Group

Target group of these instructions are:

• Installer

• Service Technician

Installers and service technicians are skilled personnel who have the specialist knowledge required for instal-

lation, commissioning, and maintenance.

1. Safety and Compliance

1.1 Safety Information

WARNINGS

• Live parts inside.

• The handling and installation of this device is recommended for a professional.

• Use of an unsuitable power supply unit may cause product failure or injury.

• Do not remove the cover plates or face plate.

• Ensure installation does not expose sharp edges of the product to users.

UL REQUIREMENTS

• If the unit is installed on a fire exit door the product installation shall be allowed only if

accepted by a local AHJ authority having jurisdiction and comply with NFPA 101.

• The unit is to be connected and controlled via a UL 294 or FWAX7 listed Access Control Unit.

• That the unit shall be installed in accordance to NFPA 70 along with any additional

requirements imposed by the local authority of jurisdiction.

• Do not connect the unit to a receptacle controller by a switch.

• If the unit is installed in conjunction with panic hardware the lock shall be installed in a

manner to not impair panic device operations.

• The unit shall be powered by a UL 294 or UL 2610 listed power supply with a Class 2 power

limited output.

• All factory tested grades were not evaluated by UL.

• UL1034 rating only applies when product is installed in a mortised application.

1.1 Regulatory Compliance Information

This product is in compliance with the CE Directives including Electomagnetic Compatibility (EMC) Directive,

Restriction of the use of certain hazardous substances (RoHS) Directive, and Registration, Evaluation,

Authorisation and Restriction of Chemicals (REACH) Regulation.

This product is in compliance with the United Kingdom (UK) Legislation including the Electromagnetic

Compatibility Regulation 2016, and the Restriction of the Use of Certain Hazardous Substances in Electrical

and Electronic Equipment Regulations 2012.

CE and UKCA Declaration of Conformity is available at www.dormakaba.com.

EN14846:2008

1 2 3 4 5 6 7 8 9

3 X 9 0* / G 2 1 1

*Grade 0 for classification 4 ‘Suitability for use on fire/smoke doors’ applies only to the product when used

as a primary latching device for a fire/smoke door. The product is suitable for use on a fire/smoke door when

installed as an auxiliary locking device alongside a primary latching device with appropriate test evidence.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning

used electrical and electronic appliances (waste electrical and electronic equipment

- WEEE). The guideline determines the framework for the return and recycling of used

appliances as applicable throughout the EU.

In Countries Outside the European Union and EEA (Norway, Iceland, and Liechtenstein): If

you wish to dispose of this product please contact your local authorities and ask for the

correct way of disposal.

This product is in compiance with the Regulatory Complaince Mark (RCM) for Australia and

New Zealand.

This product is regulated by the UL/CSA and bears UL/C-UL certification.

Certifications: UL294, UL1034, ULC-S533-15

UL File Number: BP7604

UL Catagories: CVXY, ALVY, FWAX7

UL294

Line Security Level I

Standby Power Level I

Attack Level I

Endurance Level IV

UL1034

Static Strength: 1,500 lbf (6,673N)

Dynamic Strength: 70 ft·lbf (95J)

Endurance: 250,000 cycles

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

residential, commercial, or industrial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

Modifications: Any modifications made to this device that are not approved by the

manufacturer may void the authority granted to the user by the FCC to operate this

equipment.

Innovation, Science and Economic Development Canada ICES-003:

CAN ICES-3(B)/NMB-3(B)

1.1 Product Description

The SL30DBL is a motor driven low voltage electric lock designed to secure commercial and residential swing-

through (180°) doors. The lock has been designed to address the two biggest issues in concealed electric

locking today;

1. The ability to ‘pull’ a door into alignment even if the door has not closed in a central position.

2. The ability to release when requested even if there is excessive load on the door.

The design of the SL30DBL is unique as it has two motors which independently operate two bolt pins. The bolt

pins operate on a cam action which enables each bolt pin to pull a door into place. In practice as the door

closes it may come to rest in a position that is not fully closed. The SL30DBL senses when the door is within

8mm (5/16 inch) of being fully closed in either direction and activates the bolt pin. This is an effective 16mm

(10/16 inch) alignment window. The bolt pin then rotates out and pulls the door from its resting position to

the closed and secured position.

With the door secured and locked the SL30DBL can be given an unlock signal and it will instantly unlock. If

the door is loaded (pre-load) when the unlock signal is given the SL30DBL will still unlock, even with loads

in excess of 100kg on the door from either side. Critically the ability of the SL30DBL to instantly release with

excessive pre-load on the door even occurs in the event of a power failure if the lock is configured as fail safe.

Additional features of the SL30DBL are;

• Multi-voltage input (12 - 24VDC)

• Very low current consumption

• Door position and bolt position monitors

• High physical strength

• Fail-safe / Fail-secure on-site conversion with the re-positioning of a single switch

1.1 Package Contents

1x Lock 1x Strike Plate

4x 10G self-tapping screws 1x 300mm 7-way wire loom

1.1 Technical Data

Materials

Bolt Stainless Steel 17-4PH

Lock / Strike Plate Stainless Steel 304

Mechanical

Bolt Extension 13mm

Door Gap max. 6mm (¼ inch)

Misalignment Correction max. 8mm (5/16 inch)

Cycle Life 1,000,000 cycles

Holding Force 10,000N (2,250 lbf) (factory tested only)

Side Load Release 6,000N (1,350 lbf) (factory tested only)

Locking Time 1.0 seconds (typical)

Unlocking Time 0.3 seconds (typical)

Environmental

Operating Temperature -10°C to +55°C

Electrical

Power Requirements 12-24 VDC ±15%

Initial Power Up Time 11 seconds

Initial Current Draw 750mA@12VDC, 400mA@24VDC

Standby Current 40mA@12VDC, 25mA@24VDC

Signal Contacts Bolt Position (NO) 30VDC max., 100mA max.

Door Position (NO)

Compliance

CE, UKCA, UL, FCC, IC, RCM, RoHS 2

1. Product Dimensions

1.1 Lock Dimensions

The dimensions shown are approximate and subject to change without prior notice.

183mm

7.205in

47mm

1.854in

3mm

0.118in

255mm

10.039in

10mm

0.394in

235mm

9.252in

10mm

0.394in

30mm

1.181in

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Dormakaba

Dormakaba

Dormakaba 8H Series Manual de usuario

Dormakaba

Dormakaba Classic Manual de usuario

Dormakaba

Dormakaba 5715 Instrucciones de funcionamiento y mantenimiento

Dormakaba

Dormakaba AUDITCON 2 SERIES Manual de usuario

Dormakaba

Dormakaba ORACODE 480 Series Manual de usuario

Dormakaba

Dormakaba LA GARD ComboGard Pro 39E Manual

Dormakaba

Dormakaba LA GARD 700 Series Manual de usuario

Dormakaba

Dormakaba LA GARD 700 Series Manual de usuario

Dormakaba

Dormakaba GL220 Manual de usuario

Dormakaba

Dormakaba LA GARD 700 Series Manual de usuario

Dormakaba

Dormakaba RCI 3513-DM Manual de usuario

Dormakaba

Dormakaba YD30S Manual

Dormakaba

Dormakaba La Gard Reset Box Manual de usuario

Dormakaba

Dormakaba Confidant RFID Kit 2 Manual de usuario

Dormakaba

Dormakaba Axessor CIT Manual de usuario

Dormakaba

Dormakaba UNIQUIN Manual de usuario

Dormakaba

Dormakaba Kaba Star Manual de usuario

Dormakaba

Dormakaba YD30 Series Manual

Dormakaba

Dormakaba STV 2 Series Manual de usuario

Dormakaba

Dormakaba Axessor Series Manual de usuario

Dormakaba

Dormakaba RCI DE8310 V1.6 Manual de usuario

Dormakaba

Dormakaba SVI 5000 Manual de capacitación

Dormakaba

Dormakaba 79 Series Instrucciones de montaje

Dormakaba

Dormakaba RCI DE8310 Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario