Dormakaba GL10 Manual de usuario

INSTALLATION AND OPERATING INSTRUCTIONS

Electronic Gate Lock GL10

Page

CONTENTS

•DESCRIPTION

•PRODUCT UNBOXED

•PRE - INSTALLATION ASSESMENT

oMechanical

oElectrical

•INSTALLATION

oMark the lock position

oDrill the lock mounting holes

oSecure the lock in position

oMark the strikes position

oDrill the strikes mounting holes

oSecure the strike in position

oWire the lock

oCover the lock

•WIRING

•OPERATING CONFIGURATION

oFail State

oAuto re-lock

oTimed re-lock

oDiagnostic mode

•OPERATION

oAuto re-lock ON

oAuto re-lock OFF

oGeneral

oAlarms

•SPECIFICATIONS

•DIMENSIONS

oLock

oStrike

•MAINTENANCE

•WARRANTY

•UPGRADE

Page

1. DESCRIPTION

The GL10 is a low voltage motor driven lock suited for securing vehicle and pedestrian gates. It is supplied with a

matching strike plate and can be installed externally or internally in a horizontal or vertical position. It is designed for

use on single or double gates and can be mounted to suit hinged or sliding applications. A solid 18mm diameter

stainless steel bolt pin ensures the highest strength while a bolt pin extension of 35mm offers flexible installation.

Integrated electronics provide complete control over the lock and offer an array of features;

▪Multi–voltage input (12-24VDC)

▪Multiple locking / unlocking attempts to correct miss-aligned gates

▪Selectable automatic locking when the gate closes

▪Fail safe / Fail secure user selection with a single switch

▪Gate position monitoring

▪Bolt locked and Bolt unlocked monitors

The lock incorporates a keyed manual override and wiring can be run securely through the locks base or externally

through a 20mm wiring gland.

2. PRODUCT UNBOXED

Lock Cover with two keys Lock Strike

Also included in the box are 4 x AA batteries. Because of the various fitting locations of the GL10, no mounting

bolts are supplied. The mounting holes in the lock and strike are 8.5mm slotted holes so accept M8 size bolts.

3. PRE - INSTALLATION ASSESMENT

3.1 Mechanical

Before the lock can be installed, consider its location and orientation. The GL10 can be mounted horizontally or

downwards vertically but it cannot be mounted vertically locking upwards. Mounting it in this way can allow water

to penetrate that lock and will void the warranty. Depending on the chosen mounting position, spacers or packers

may need to be made and used.

When positioning the strike, it is important to achieve a reasonable level of alignment with the bolt pin as to ensure

correct locking and operation. The hole in the strike is of significantly larger diameter than that of the lock pin, however

installing the strike so the lock pin goes into the hole centrally is best as it will allow for movement of the gate over

time.

There are three magnets in the strike which offers the flexibility of mounting options and with the symmetrical design

of the lock, the strike can approach from either the right, left or bottom face of the lock.

Page

Lock mounted to the ground. Lock mounted to the gate frame horizontally.

Lock mounted to the gate frame vertically down. DO NOT mount the lock vertically up.

3.2 Electrical

After the positions of the lock and strike are determined, establish where to run the wires and also decide on what

feedback is required from the lock. There are a total of eleven available connections on the GL10; three are

compulsory and eight are optional. The three essential connections are; Positive (+), Negative (-) and Control (CL).

There need to be wires run from the power source and control switch to the lock.

The eight optional connections all provide feedback about the locks state; Gate Position, Bolt Locked Position and

Bolt Unlocked Position. If desired, wires can be run from these connections to integrate into access control or alarm

systems to provide full monitoring.

Once the number of wires and their destination is determined, it needs to be decided how the wires will enter the

lock. They can either come in through a 20mm weather proof wiring gland at the rear of the lock (not supplied), or

through a hole under the locks base which will ensure the wires can be hidden.

Finally, the correct wire gauge needs to be chosen to ensure a minimal voltage drop. The correct wire gauge is

important when connecting the power wires (+ and -) to the lock as voltage drop across these wires can limit the

locks operation and prematurely deplete the batteries. For all the remaining connections, a lower gauge wire can be

used as these are only signal wires.

The following chart shows the appropriate wire gauge for a range of distances between the lock and power supply.

Distance (m)

AWG Size

Metric Size (mm2)

Wire Diameter (mm)

12VDC

24VDC

12VDC

24VDC

12VDC

24VDC

0.21

0.51

0.33

0.21

0.65

0.51

0.83

0.52

1.02

0.82

100

1.31

1.29







Page

4. INSTALLATION

A typical vehicle gate lock installation is described. The lock is being mounted to the fence post while the strike will

be mounted to the gate on the left of the lock. Coach bolts would be used to secure the lock and strike.

4.1 Mark the lock position

Locate the lock in the desired position and

using a pen / pencil mark the three mounting

hole locations through the lock base.

4.2 Drill the lock mounting holes

Use a M8 drill bit to drill the three mounting

holes in the fence post.

Check on the preferred

wiring method and if running

the wires through the base

is desired, also mark and

drill the wire hole now.

See section 5 - Wiring.

4.3 Secure the lock in position

Push the bolts through the fence post and

position the lock over the protruding bolt ends.

Place nuts on the three bolts and tighten

them to secure the lock to the post.

4.4 Mark the strikes position

Locate the strike in the correct position and

using a pen / pencil mark the three mounting

hole locations through the strike.

Page

4.5 Drill the strikes mounting holes

Use a M8 drill bit to drill the three mounting

holes in the gate.

4.6 Secure the strike in position

Push the bolts through the gate post and

position the strike over the protruding bolt ends.

Place nuts on the three bolts and tighten

them to secure the strike to the gate.

4.7 Wire the lock

Using a screwdriver and following the

connection guide on the printed circuit board,

connect the required wires to the lock.

Detailed wiring information can

be found in section 5 - Wiring

4.8 Cover the lock

Position the cover over the lock and push it

down and forward. Use the keyed cam lock

in the back of the cover to secure it in place.

Page

Wires run through a gland in the rear off the lock.

Wires run out of the hole in the base of the lock.

5. WIRING

Connect the GL10 as per the chart below. The three power connections are vital for the operation of the lock whilst

the eight monitor connections are outputs supplied to offer feedback if desired.

Power

Positive connection to DC power supply (12 –24V)

Negative connection to DC power supply (12 –24V)

Switched positive control input

Bolt Position Switch - Unlocked

Normally closed contact of the bolt position unlocked monitor

Normally open contact of the bolt position unlocked monitor

Common contact of the bolt position unlocked monitor

Bolt Position Switch - Locked

Normally closed contact of the bolt position locked monitor

Normally open contact of the bolt position locked monitor

Common contact of the bolt position locked monitor

Door Position Switch

Normally open contact of the gate position monitor

Common contact of the gate position monitor

There are two options available when running wires into the GL10; they can be brought in through a 20mm wiring

gland (not supplied) in the rear of the cover, or run discreetly through the hole in the locks base.

Running wires out of the lock via the hole in base ensures a more weather proof and secure installation as the wires

can be concealed. If the preferred option is to use a 20mm wiring gland, a hole is available in the rear of the cover to

achieve this. This hole is covered by a factory fitted blank held in place by an M3 screw that can be removed.

6. OPERATING CONFIGURATION

The operating configuration of the GL10 controls how the lock will function and there are several settings available.

There are four dip switches on the printed circuit board with three being used to configure the lock and the fourth for

diagnostic purposes. The dip switches are located on the top of the printed circuit board and can be set as per the

following table.

Page

Fail Safe operation

With batteries fitted, in the event of a power failure the GL10 will unlock

OFF

Fail Secure operation

With batteries fitted, in the event of a power failure the GL10 will lock

Auto re-lock on

The GL10 will automatically lock when the gate closes

OFF

Auto re-lock off

The GL10 only locks when the user desires

Timed re-lock on

The GL10 will re-lock after one minute if an unlock signal is given and

the gate remains closed - Auto re-lock must also be enabled

OFF

Timed relock off

The GL10 will never re-lock if an unlock signal is given and the gate

remains closed

Diagnostic mode on

The GL10 goes into a service mode to output information*

OFF

Diagnostic mode off

The GL10 operates as normal

*Should only be activated in the event of a failure.

6.1 Fail State –Switch 1

The fail state of the GL10 is determined by the selection of switch 1; however there is an additional state that can be

used if desired. With no batteries installed the lock will default to Fail Maintained. In this configuration and in the

event of a power failure, the lock will stay in the position it was in before the power was removed. With the batteries

fitted however, selecting Fail Safe or Fail Secure ensures that the GL10 will move to that selected state if the power

does fail.

6.2 Auto re-lock –Switch 2

It is recommended that Auto re-lock be ON in most installations. The ability of the GL10 to sense the gates position

and automatically lock when it is closed is paramount to increasing security as it eliminates the need for the user to

do so. If Auto re-lock is not selected the GL10 operates on a toggle method. In this configuration an activation of the

control signal will cause the GL10 to unlock and a second activation will cause it to lock, assuming the strike is in

place.

6.3 Timed re-lock –Switch 3

Timed re-lock can only be enabled when Auto re-lock has been selected and it is recommended to be ON in most

installations. For increased security the GL10 has the ability to automatically lock itself after a timed period in the

event of a user failing to do so. If an unlock signal is given to the lock but the gate is not opened the GL10 can

automatically lock itself again after one minute. This ensures that a gate can not be left unsecured if it has been

unlocked but not opened.

6.4 Diagnostic mode –Switch 4

By default the Diagnostic mode should be set to OFF. If the GL10 fails then the Diagnostic mode can be activated

and information extracted from it to help determine what has caused the fault. This information needs to be interpreted

by a registered distributor or the original manufacturer.

7. OPERATION

The operating scenarios detailed below stay the same regardless of whether the GL10 is configured in a Fail Safe,

Fail Secure or Fail Maintained state. The state of the lock is only relevant in the event of a total power failure. Both

scenarios assume that the control signal is open at the start of the operation sequence as a maintained connection

will cause the lock to stay unlocked indefinitely.

Page

7.1 Auto re-lock ON

With Auto re-lock ON selected,

the momentary connection of

CL to + acts as the unlock signal.

Closing the gate so the strike

aligns with the lock and the

magnet activates the internal

switch, acts as the lock signal.

7.2 Auto re-lock OFF

With Auto re-lock OFF selected,

the momentary connection of

CL to + acts as both the lock

and unlock signals for the GL10.

YES

GATE CLOSES

HAS THE

GATE OPENED?

UNLOCK SIGNAL

HAS THE BOLT PIN

RETRACTED AFTER

3 ATTEMPTS?

GL10 IN STANDBY

GATE IS UNLOCKED

GL10 IN STANDBY

GATE IS LOCKED

HAS THE BOLT PIN

EXTENDED AFTER

3 ATTEMPTS?

HAS A LOCK

SIGNAL BEEN SENT

YES

GATE CLOSES

INTERNAL

ALARM SOUNDS

HAS THE BOLT PIN

EXTENDED AFTER

3 ATTEMPTS?

IS THE

GATE OPEN?

HAS THE GATE

OPENED WITHIN

1 MINUTE?

UNLOCK SIGNAL

HAS THE BOLT PIN

RETRACTED AFTER

3 ATTEMPTS?

GL10 IN STANDBY

GATE IS UNLOCKED

GL10 IN STANDBY

GATE IS LOCKED

IS THE TIMED

RE-LOCK ON?

INTERNAL

ALARM SOUNDS

INTERNAL

ALARM SOUNDS

INTERNAL

ALARM SOUNDS

Page

Clockwise turning of the large

gear will retract the bolt pin.

Anti-clockwise turning of the large

gear will extend the bolt pin.

The GL10 features multiple locking / unlocking to allow for misaligned gates or unforeseen problems. If the bolt pin

meets an obstruction as it is trying to secure the gate, it stops and withdraws before attempting to lock again. It has

a total of three attempts to secure the gate after which time it will sound an alarm. The same function is present when

the GL10 unlocks.

7.3 General

If the batteries are fitted and the power is removed to the GL10 at any time during its operation, the lock will revert to

its pre-selected state of either unlocked or locked. The GL10 has been designed to operate with high quality

disposable alkaline batteries and may not work correctly with alternatives. Should the batteries become flat the

lock will sound an alarm to indicate a battery change is required.

If the batteries are not replaced once they have become depleted, the GL10 will automatically revert to the Fail

Maintained state; i.e. in the event of a power failure the lock will stay in the position it was in before the power was

removed.

The three monitors can be used to provide door and bolt position information regardless of the locks configuration.

Manual operation of the GL10 is available by removing the cover to allow access to the lock mechanism. The supplied

key can be used to open and remove the cover and once access is available a screwdriver can be inserted into the

centre of the large gear and turned to move the bolt pin in or out.

7.4 Alarms

To offer instant feedback about the locks state, the GL10 has an on board beeper which sounds at various times.

The table below details the different alarms expected from the GL10.

Locked confirm

1 Short beep

Unlocked confirm

2 Short beeps

Failure to lock / unlock

5 Long beeps

Battery replacement

5 Short beeps sounded 5 seconds after a lock activation and repeated every

10 minutes until the batteries are replaced

Diagnostic

Various beeps –used for service

Tabla de contenidos

Otros manuales de Cerrar de Dormakaba

Dormakaba

Dormakaba 2725-K6 Manual de usuario

Dormakaba

Dormakaba RCI 3513-DM Manual de usuario

Dormakaba

Dormakaba RCI DE8310 V1.6 Manual de usuario

Dormakaba

Dormakaba SL30DBL Cobalt Double Manual de usuario

Dormakaba

Dormakaba Kaba Star Manual de usuario

Dormakaba

Dormakaba LA GARD 700 Series Manual de usuario

Dormakaba

Dormakaba SVI 5000 Manual de capacitación

Dormakaba

Dormakaba LA GARD 700 Series Manual de usuario

Dormakaba

Dormakaba 79 Series Instrucciones de montaje

Dormakaba

Dormakaba Confidant RFID Kit 2 Manual de usuario

Dormakaba

Dormakaba SafeRoute-System Mini Manual de usuario

Dormakaba

Dormakaba M Series Manual de usuario

Dormakaba

Dormakaba UNIQUIN Manual de usuario

Dormakaba

Dormakaba STV 2 Series Manual de usuario

Dormakaba

Dormakaba SVI Series Manual de usuario

Dormakaba

Dormakaba 8H Series Manual de usuario

Dormakaba

Dormakaba digital cylinder Manual de usuario

Dormakaba

Dormakaba 5715 Instrucciones de funcionamiento y mantenimiento

Dormakaba

Dormakaba LA GARD ComboGard Pro 39E Manual

Dormakaba

Dormakaba Axessor Series Manual de usuario

Dormakaba

Dormakaba UNIVERSAL Light US 10 Manual de usuario

Dormakaba

Dormakaba STV 1 Series Manual de usuario

Dormakaba

Dormakaba Cobalt Single Manual de usuario

Dormakaba

Dormakaba YD30S Manual

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario