Dormakaba digital cylinder Manual de usuario
dormakaba digital cylinder
1220013692 - 11/2017
EN
Technical Manual
dormakaba Schweiz AG
Mühlebühlstrasse 23
8620 Wetzikon
Switzerland
T: +41 (0)44 931 61 11
www.dormakaba.com
dormakaba Austria GmbH
Ulrich-Bremi-Straße 2
3130 Herzogenburg
Austria
T: +43 (0)2782 808 0
www.dormakaba.com
Copyright © dormakaba 2017
All rights reserved.
No part of this document may be reproduced or used in any form or by any means without prior written permis-
sion of dormakaba Schweiz AG.
All names and logos of third-party products and services are the property of their respective owners.
Subject to technical changes.
1220013692 - 11/2017
Table of contentsTechnical Manual
31220013692 - 11/2017 dormakaba digital cylinder
Table of contents
1 About this document 5
1.1 Validity 5
1.2 Target group 5
1.3 Contents and purpose 5
1.4 Supplementary documentation 6
1.5 Digital cylinder abbreviations 6
1.6 Hazard categories 6
1.7 Notes 7
1.8 Symbols 7
2 Basic safety instructions 8
2.1 Proper use 8
2.2 Product changes 8
2.3 Use in emergency exit or panic door locks 8
2.4 Areas of use 9
2.5 ESD protective measures 10
2.6 Handling of lithium batteries 10
3 Product description 11
3.1 Overview 11
3.1.1 Structure 11
3.2 Scope of delivery 11
3.2.1 Also for dual digital cylinder 11
3.3 Accessories 11
3.4 Technical data 12
3.4.1 Dimensions 13
3.5 Conformity 16
4 Installation 17
4.1 Requirements 17
4.1.1 Door components 17
4.1.2 Tools required 18
4.2 Installation versions 19
4.2.1 Installation version A 20
4.2.2 Installation version B 22
4.2.3 Function check on anti-panic digital cylinder 24
5 Programming 25
5.1 Initial programming of MRD components 25
5.2 Initial programming of LEGIC® and MIFARE components 25
5.3 Master media 25
5.4 User media 25
5.5 Program structures 26
5.6 A/B and B structures 26
5.7 Programming user media with B masters 27
5.8 Deleting individual user media 28
5.9 Deleting individual B masters 29
5.10 Deleting all user media 30
5.11 INI reset with master media for whitelist and CardLink™ 31
6 Operation 33
6.1 Operating the digital cylinder 33
6.2 Opening with user media 33
Table of contents Technical Manual
4 1220013692 - 11/2017dormakaba digital cylinder
7 Maintenance 34
7.1 Maintenance table 34
7.2 Maintenance of escape doors 34
7.3 Cleaning 35
8 Service 36
8.1 Serial numbers 36
8.2 Replacing the battery 36
8.3 Replace e-module 38
8.4 Disassembling the inner door knob 39
8.4.1 'Click' door knob 39
8.4.2 'Small' inner knob 39
8.5 Configuration and traceback 39
8.6 Reset (INI reset) 39
8.6.1 Reset with master media 40
8.6.2 Reset using programmer 1460 40
8.6.3 Reset using tweezers 40
8.7 Emergency power supply 40
9 Troubleshooting 41
9.1 Error analysis 41
9.2 Error analysis for battery life 43
10 Appendix 44
10.1 Summary of various factors influencing the battery operation 44
10.2 Recommendations for battery operation 44
About this documentTechnical Manual
51220013692 - 11/2017 dormakaba digital cylinder
1 About this document
This section contains information for the proper use of this document.
1.1 Validity
This document describes the product:
Product designation: dormakaba digital cylinder
Types: 143X dormakaba Digital cylinder with Euro profile (17mm)
153X dormakaba Digital cylinder with round profile (22mm)
Article numbers and vari-
ants:
Euro profile cylinder 1435 Standard
1434 Half
1437 Anti-panic
1439 Dual
1431 Asymmetrical
1433 Half with turning range
Round profile cylinder 1535 Standard
1534 Half
1537 Anti-panic
1539 Dual
1531 Asymmetrical
1533 Half with turning range
All versions are available with wireless functionality.
With the exception of the asymmetrical version, all components
are available as ‘protected’ variants (with high anti-drill protec-
tion).
1.2 Target group
This document is intended for specialist personnel only.
The descriptions are tailored to specialist personnel trained by the manufacturer. The descrip-
tions are no replacement for product training.
Service personnel are persons who have the appropriate technical training and experience re-
quired for them to be aware of the risks that could arise for themselves or others when carry-
ing out these activities and to minimise these risks for themselves and others. It is the re-
sponsibility of the service personnel to ensure that the conditions stated by the manufacturer
and the applicable regulations and standards are complied with when carrying out these
activities.
1.3 Contents and purpose
The contents of these instructions are limited to the installation, operation, maintenance and
servicing of the product.
About this document Technical Manual
6 1220013692 - 11/2017dormakaba digital cylinder
1.4 Supplementary documentation
The following documents are available from the sales partners:
• Programmer 1460 technical manual
• Operating manual for programmer 1364
• Wireless operation: Wireless planning guideline
• Documentation for the system software used
1.5 Digital cylinder abbreviations
Short designation Product designation
Digital cylinder dormakaba digital cylinder
Programmer Programmer 1460
1.6 Hazard categories
Instructions with information on what to do and not to do to prevent injury and material
damage are denoted specially.
Please follow all hazard instructions. These are intended to help prevent accidents and pre-
vent damage.
These instructions are divided into the following categories:
DANGER
High risk
Denotes an immediate danger that could lead to serious injury or death.
WARNING
Medium risk
Denotes a potentially dangerous situation that could lead to serious injury or death.
CAUTION
Low risk
Denotes a potentially dangerous situation that could lead to minor injury.
NOTICE
Important information on the correct use of the product.
Failure to comply with these instructions could lead to malfunctions. The product and/or ob-
jects in the local vicinity could be damaged.
About this documentTechnical Manual
71220013692 - 11/2017 dormakaba digital cylinder
1.7 Notes
Information is denoted by this symbol.
Tips on using the product are useful pieces of information.
They help to make best use of the product and its functions.
1.8 Symbols
Symbols with the following meanings are used for hazards (depending on hazard source.)
General hazard Hazard from electric shock
Risk of explosion Risk to electronic components from
electrostatic discharge
Basic safety instructions Technical Manual
8 1220013692 - 11/2017dormakaba digital cylinder
2 Basic safety instructions
This product has been built to state-of-the-art standards and in line with established safety
regulations. However, hazards for persons and property may arise when handling the product.
Read and observe the following safety instructions before using the product.
2.1 Proper use
This product has been designed exclusively for use as set out in the chapter Product Descrip-
tion. Any other use will be deemed improper use. The manufacturer accepts no liability for any
resulting damage. The user/operator bears sole responsibility for the risk.
2.2 Product changes
NOTICE
No changes should be made to the product, unless in accordance with changes described in
the instructions.
2.3 Use in emergency exit or panic door locks
WARNING
Risk of personal injury or death.
• Improper use or incorrectly installed digital cylinders can lead to emergency exit locks or
panic door locks and doors not opening.
• The use of a digital cylinder must be checked carefully before using it in locks with a panic
function.
• Before installing the digital cylinder in an escape door, a check must be carried out to en-
sure that the function of the lever handle or the panic push bar is not obstructed by the
inside knob.
• The use of a digital cylinder in emergency exit locks in accordance with EN179 or in panic
door locks in accordance with EN1125 is documented in the lock manufacturers' perform-
ance declarations. If the digital cylinder is not listed in the performance declarations or
certificates from the lock manufacturer or the lock does not comply with these standards,
an EC conformity inspection of the lock, digital cylinder, fitting and assembly accessories
as one unit must be carried out.
Basic safety instructionsTechnical Manual
91220013692 - 11/2017 dormakaba digital cylinder
2.4 Areas of use
IP56
When used outdoors, the cylinder must be protected against sustained rainfall using a
weather guard.
NOTICE
Freezing liquids can disrupt the function, resulting in doors not opening. No water, therefore,
should get into the cylinder. When used externally, the cylinder must be protected against
sustained rainfall using a weather guard.
When used in fire protection doors, escape routes or rescue routes, the locally applicable
guidelines and building regulations must be observed.
NOTICE
Doors at risk of forced entry
• The following points must be observed for certification as per VdS Class B: On doors at
risk of forced entry, the 'Protected' version of the digital cylinder must be protected with
a VdS-recognised burglary-resistant Class B or C doorplate. These doorplates correspond
to DIN 18 257 Class ES 2 or ES 3 and EN1906 Class 3 or 4. The cylinder must protrude no
more than 3 mm beyond the doorplate.
• The user media (keys, badges, etc.) must always be kept safe to ensure only authorised
personnel may gain access. If identification media are lost, the authorisation data must
be blocked and deleted from all cylinders immediately.
NOTICE
Wrong type of lock
The asymmetrical digital cylinder is not permitted to be used in some lock types.
Please refer to the lock manufacturer’s instructions.
Basic safety instructions Technical Manual
10 1220013692 - 11/2017dormakaba digital cylinder
2.5 ESD protective measures
NOTICE
Danger of damage to electronic components from electrostatic discharge.
If electronic printed circuit boards and components are handled incorrectly, damage may oc-
cur which leads to their complete breakdown or sporadic faults.
• When installing and repairing the product, the general ESD protective measures are to be
observed.
• Before starting service or maintenance work on the product, e.g. changing the battery,
briefly touch the door handle. This will safely and effectively conduct charges away from
your body.
• When handling electronic components, wear the ESD wrist strap. Connect the end of the
strap to an ESD socket or an unpainted, earthed metal component. This will safely and ef-
fectively conduct charges away from your body.
• Only handle the edges of printed circuit boards. Do not touch printed circuit boards or
connecting plugs.
• Put removed components on an anti-static surface or in an anti-static shielding container.
• Avoid contact between printed circuit boards and clothing. The wrist strap only protects
the printed circuit boards from static electricity on the body. Damage can still occur due
to static electricity on clothing.
• Only transport and ship removed modules in ESD-shielding, conductive protective con-
tainers.
2.6 Handling of lithium batteries
NOTICE
Lithium batteries can explode or burst explosively.
Improper handling of lithium batteries can lead to fires and explosions.
• Only replace lithium batteries with batteries of the same type.
• Do not open, drill through or squash lithium batteries.
• Do not burn lithium batteries or expose them to high temperatures.
• Do not short circuit lithium batteries.
• Do not recharge lithium batteries.
Tabla de contenidos
Otros manuales de Cerrar de Dormakaba
Dormakaba
Dormakaba ORACODE 660i Manual de usuario
Dormakaba
Dormakaba GL220 Manual de usuario
Dormakaba
Dormakaba STV 1 Series Manual de usuario
Dormakaba
Dormakaba Confidant RFID Kit 2 Manual de usuario
Dormakaba
Dormakaba Kaba Star Manual de usuario
Dormakaba
Dormakaba YD30D Manual
Dormakaba
Dormakaba GL10 Manual de usuario
Dormakaba
Dormakaba UNIVERSAL Light US 10 Manual de usuario
Dormakaba
Dormakaba RCI DE8310 Manual de usuario
Dormakaba
Dormakaba SVI 5000 Manual de capacitación
Dormakaba
Dormakaba Classic Manual de usuario
Dormakaba
Dormakaba 2725-K6 Manual de usuario
Dormakaba
Dormakaba Axessor Series Manual de usuario
Dormakaba
Dormakaba UNIQUIN Manual de usuario
Dormakaba
Dormakaba La Gard Reset Box Manual de usuario
Dormakaba
Dormakaba SafeRoute-System Mini Manual de usuario
Dormakaba
Dormakaba SL30DBL Cobalt Double Manual de usuario
Dormakaba
Dormakaba 8H Series Manual de usuario
Dormakaba
Dormakaba ORACODE 480 Series Manual de usuario
Dormakaba
Dormakaba SVI Series Manual de usuario
