Digitus DN-651138 Manual de usuario
16-port 10/100/1000Base-TX
+2x Gigabit SFP Industrial
Ethernet Switch
Quick Installation Guide
DN-651138
2
1. Overview
Industrial Ethernet switch with 16-Port 10/100/1000Mbps Base-TX
and 2-Port Gigabit SFP, the Product meet CE, FCC, RoHS standards.
DN-651138 switch has the operating temperature of -40°C ~ 80°C, has
the super firmness can adapt to all kinds of harsh environment, can
also be conveniently placed in the compact space of the control box.
The installation characteristics of the guide rail, wide temperature
operation, IP40 protection class housing and LED indicator light make
the DN-651138 a plug and play industrial grade device, providing a
reliable and convenient solution for users to network their Ethernet
devices.
2. Switch Panel
Side panel: P1 and P2 are the number of connecting terminals, and
F is the interface of alarm. P+1 and P-1 are respectively to the positive
and negative poles to be connected; Earthing screw, used for earthing
equipment.
Front panel: The Yellow LED on the port is the LINK light, which is on
when the connection is established and the data transmission is
flashing.
3
The green LED is POE light, which is only on when the switch port is
supplying power to PD device (this model is not to support PoE);
Power indicator light is on when connecting with Power.
Switch size (mm)
3. Features
Support long range transmission by fiber optical port.
Full working temp. -40 ~ 80 °C to ensure reliable data and
long working life
In line with industrial operating standards, the average
trouble-free work in more than 300,000 hours dual power input
Lightning Surge Protection (Power): 5000A (8/20μs)
DIN Rail and Wall mount support
Support full duplex or half duplex mode, with automatic
negotiation capability
Network port support automatic cross identification
internal storage and forwarding mechanism
4
4. Specification
4.1 Standard:
IEEE802.310Base-T; IEEE802.3i 10Base-T; IEEE802.3u 100Base-TX/FX;
IEEE802.3ab 1000Base-T; IEEE802.3z 1000Base-X; IEEE802.3x
4.2 Interface:
16-Port RJ45; 2- Port SFP Uplink
4.3 Work environment:
Working: -40 ~ 80 °C
Storage: -40 ~ 80 °C
Relative Humidity: 5%~95 %
(No condensation)
4. 4 Switch:
Bandwidth: 56Gbps
Packet Buffer Memory: 4.1Mbit
Packet Forwarding Rate: 42Mpps
MAC Address Table: 8K
4.5 Power supply:
Input voltage: DC12-52V (two-way power redundancy backup)
Access terminal: terminal block;
Support dual power redundancy
Support built-in over current 4.0A protection
Support reverse connection protection
4.6 Mechanical characteristic：
IP40 aluminum housing
DIN rail install
Natural cooling, no fan
Weight: 1.0Kg
Measurement: 175.6 x 135 x 45.5 mm
5
4.7 Industrial standard:
FCC Part 15 Subpart B, EN55032, Class A
IEC61000-4-2 (ESD): ±8kV (contact), ±12kV (air)
IEC61000-4-3 (RS): 10V/m (80~1000MHz)
IEC61000-4-4 (EFT): Power Port: ±4kV; Data Port: ±2kV
IEC61000-4-5 (Surge): Power Port: ±2kV/DM, ±4kV/CM;
Data Port: ±2kV
IEC61000-4-6 (CS): 3V (10 kHz-150 kHz); 10V (150 kHz-80MHz)
IEC61000-4-16 (Common mode conduction): 30V (cont.), 300V (1s)
Frequency range: 150kHz-80MHz
Impact: IEC60068-2-27
Free Fall: IEC60068-2-32
Vibration: IEC60068-2-6
5. Interface Definition
5.1 10/100/1000Base-TX Ethernet interface:
This switch provides MDI/MDI-X self-identification with cable support
on all 10/100/1000Base-TX ports. In use, the Ethernet port of the
switch can be connected with other Ethernet terminal devices through
network cables (direct or cross). Please use Class 5 shielded twisted
pair. The Ethernet port pin definition is shown in the following figure:
RJ45 port supports automatic MDI/MDI-X operation, you can use a
straight line to connect to the PC or server, connect to other switches
or hubs. In the through line (MDI), pins 1, 2, 3, 4, 5, 6, 7, 8 correspond
to the connection;
6
For the MDI-X port of a switch or hub, cross lines are used: 1-3, 2-6,
3-1, 6-2, 4-7, 5-8, 7-4, 8-5.10Base-T/100Base-T (X) pins are defined as
follows:
Pin No.
MDI signal
MDI-X signal
1
TX+
RX+
2
TX-
RX-
3
RX+
TX+
6
RX-
TX-
4,5,7,8
-
-
Note: "Tx ±" refers to send data, "Rx ±" refers to received data ±, and
"-" refers to unused data.
5.2 1000base-FX Ehernet interface
This device provides 1000Base single-mode dual-
fiber SC module, and multi-mode like LC, ST as optional.
5.2.1 Patch cord classification
According to the transmission mode of light in the fiber, it can be
divided into multi-mode fiber and single-mode fiber. Multimode fiber
has a thick glass core (50 or 62.5μm), which can transmit light in
various modes. However, the high inter-mode dispersion limits the
frequency at which digital signals can be transmitted, so multimode
fibers can be transmitted over relatively close distances (typically only
a few kilometers).
The single-mode fiber has a very thin glass core (core diameter, usually
9 or 10μm) and can transmit only one mode of light. Therefore, it’s
inter – module dispersion is very small, and it is suitable for remote
communication. Under normal circumstances, the skin is orange for
multi-mode, yellow for single mode.
7
5.2.2 SFP module (Optional, not included)
LC connector, Gigabit, 20km Single mode, dual fiber (DN-81011)
LC connector, Gigabit, 20km Single mode, Single fiber
(DN-81020 and DN-81021)
8
6. LED Indicator
LED indicator
Status
Definition
P1/P2
Red LED on
Power supplying in
normal
Red LED off
Power supply abnormal
or no powering
RJ45 indicator
Yellow LED on
Network connection in
normal
Yellow LED flashing
Link communication in
normal
Yellow/Green LED off
No connection at port
Note: this model is not available with PoE
7. Installation caution
7.1 Installation precautions
In order to avoid damage to equipment and personal injury caused
by improper use, please follow the following precautions:
In order to avoid damage caused by falling of the equipment,
please put the equipment in a stable environment.
When supplying power to the equipment, pay attention to confirm
the range of power supply voltage, as well as the positive and
negative poles of the power supply, so as not to damage the
equipment by wrong operation.
In order to reduce the risk of electric shock, ensure that the
equipment is well grounded in the working environment.
No matter when, please do not arbitrarily remove
the equipment shell.
When placing the switch, please avoid the area with dust and
strong electromagnetic interference
9
7.2 Din rail installation:
The first step is to check the grounding and
stability of the guide rail: the guide rail slot of the
switch is clamped into the guide rail; The second
step: from the center to both sides of the guide
rail positioning screws in order. Step 3: Use
screws to fix the mounting rail card slot on the
fixed guide groove at both ends of the guide rail
to ensure that the guide rail and the switch are
fixed on the guide rail vertically and stably.
7.3 grounding
Fix the grounding wire to the grounding screw
above the switch, and ensure good reliable
connection of the grounding system.
7.4 Power Connection
Insert the power cord into the specified position of the 6-core terminal,
and insert the terminal into the standard power supply inlet (P+1 and
P-1 input corresponding to the first power supply P1, and P+2 and P-2
input corresponding to the second power supply P2). The available
voltage standard of the power supply is supported from 12VDC to
52VDC
10
8. Packages
Content
QTY
Industrial switch
1 PCS
Quick installation guide
1 PCS
Rackmount kit
1 SET
Terminal block
1 PCS
This is a Class A product. In home environment, this product may
cause radio interference. In this case, the user may be required to take
appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of
Conformity is part of the shipping content. If the Declaration of
Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
,
Germany
Tabla de contenidos
Otros manuales de Cambiar de Digitus
Digitus
Digitus DN-651129 Manual de usuario
Digitus
Digitus DN-651118 Manual de usuario
Digitus
Digitus DS-44100 Manual de usuario
Digitus
Digitus DA-70217 Manual de usuario
Digitus
Digitus DA-70243 Manual de usuario
Digitus
Digitus DA-70240-1 Manual de usuario
Digitus
Digitus DN-95316 Manual de usuario
Digitus
Digitus DN-95351 Manual de usuario
Digitus
Digitus DS-45310 Manual de usuario
Digitus
Digitus DA-70224-1 Manual de usuario
Digitus
Digitus DN-95355 Manual de usuario
Digitus
Digitus DA-70228 Manual de usuario
Digitus
Digitus DC-44400 Manual de usuario
Digitus
Digitus DN-50012-1 Manual de usuario
Digitus
Digitus DC-11101-1 Manual de usuario
Digitus
Digitus DS-11900 Manual de usuario
Digitus
Digitus DN-80221-3 Manual de usuario
Digitus
Digitus DS-12423 Manual de usuario
Digitus
Digitus DA-70135-3 Manual de usuario
Digitus
Digitus 3-port usb - PS/2 KVM Switches with DVI and... Manual de usuario
