Digitus DN-95330-1 Manual de usuario

DIGITUS 4 Port Gigabit PoE

Switch, Unmanaged, 1 Uplink

Quick Installation Guide

DN-95330-1

1.Introduction

The DIGITUS 5-Port Gigabit Desktop Switch with four Power over Ethernet

ports and one additional uplink Port, offers your network significant

improvement in terms of performance and efficiency. Thanks to PoE

support, you only need a single (network) cable for power and data

transfer. This switch makes it much easier to connect devices such as access

points, network cameras, and IP telephones, and requires far less cabling

than alternatives. It also allows you to extend your network in places where

there are no power supply cables or sockets available. The switch does not

require any configuration and therefore guarantees quick and seamless

integration into the network. Moreover, the switch’s fanless design ensures

soundless operation, which makes this device the perfect solution for office

environments and meeting rooms.

2.Features

1. Comply with IEEE 802.3, IEEE 802.3u, IEEE802.3x standards

2. Support IEEE802.3af, IEEE802.3at standards

3. Supports PoE: One to four ports (802.af, 15.4 Watts) or for two ports

(802.3.at, 30 Watts)

4. Automatically detect PD devices

5. PoE power budget: 60 Watts

6. Auto detect power device; will not burned non-standard PoE device or

normal PoE switch

7. Supports port power supply prioritization, guarantee the continuous

power supply of key nodes

8. Line-speed forwarding, intelligent identification

9. Supports storage –and- forward for Data exchange

10. Support One-Key CCTV and PD-ALIVE functions

11. Ethernet speed: Gigabit

12. MAC Address Table: 2K, Auto-learning, Auto-aging

13. Switching Capacity: 10Gbps

14. Fanless

15. Power Supply: 65W

16. PoE Power on RJ45: Mode A 1/2(+),3/6(-)

17. Jumbo frame: 9K Bytes

3.Package contents

1x PoE Switch

1x QIG

1x Power Cord

4.Specifications

Model

4-Port Gigabit+1GE PoE Switch

Standard

IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3az,

IEEE802.3x, IEEE802.3af, IEEE802.3at

Network -

Media(Cable)

10BASE-T: UTP category 3,4,5 cable（≤100m）

100BASE-TX: UTP category 5, 5e cable（≤100m）

1000BASE-T: UTP category 5e, 5 cable（≤100m）

MAC Address Table

2K, Auto-learning, Auto-aging

Jumbo Frame

9K Bytes

Packet Buffer

1Mbit

Transfer Mode

Store-and-Forward

Switching Capacity

10Gbps

Packet Forward

Speed

7.44Mpps

PoE Port

Port1~4

PoE Output-port

Max 30W

RJ45 PoE Power

Supply

Mode A 1/2(+) 3/6 (-)

PoE Total

60W

Power Supply

65W

Dimensions

(L*W*H)

140*68*27.7mm

Fan

Fanless

Input Voltage

AC 100-240V 50/60Hz

Temperature

Operating Temperature: 0°C ~ 40 °C

Storage Temperature: -40 °C ~70°C

Humidity

Operating Humidity: 10% ~ 90% non-condensing

Storage Humidity: 5% ~ 90% non-condensing

5.Hardware Description

Front Panel

The front panel consists of 5*10/100/1000Mbps adaptive RJ45 ports and

related indicators, as shown in the following figure:

LED Indicator

DIP Switch

5*10/100/1000 Mbps RJ45 Ports

4-Port Gigabit+1GE Port description:

10/100/1000Mbps RJ45 Ports

Supports 10Mbps, 100Mbps and 1000Mbps rate adaptation, and supports

auto-MDI /MDIX. 1-4 ports support PoE power supply. PoE ports

automatically detect PD devices and supply power to PD devices that

comply with IEEE 802.3af/at standards. Each port has a maximum of 30W.

Each port has a corresponding indicator, that is, the indicators 1-5 on the

panel in the figure above.

DIP Switch

The DIP switch located on the left panel.

Default mode: when CCTV closed the factory default mode can normal

communication between port 1~5

CCTV mode: 1-4 port can be isolated each other but 1-4 port can connect

to 5-port after open CCTV to stop broadcast storm to increase forwarding

rate of frame. The CCTV mode, up to 250m PoE distance allows you to

expand you network via Ethernet cable to where there is no power line or

outlet but where you want to fix device such as IP Cameras.

Note: after changing the mode, there is no need to restart manually.

LED Indicator

The LED indicators of the Switch are shown in the following table. Users can

monitor the work and running status of the Switch conveniently and quickly

through the following indicators:

LED

Color

Function

PWR

Green

Off: No Power supply.

Light: Indicates the Switch has power.

PoE

Orange

Off: No PoE powered device (PD) connected.

Light: There is a PoE PD connected to be port,

which supply power successfully.

Blink: Indicates port abnormal PoE supply.

LNK/ACT

Green

Off: The network is not connected

Steady on: A 10/100/1000Mbps network

device is connected

Blinking: Data is being transferred

Rear Panel

The rear panel indicates AC inlet power socket. Select different power

supplies corresponding to different voltage inputs as follows:

Note: the lightning protection grounding column is located on the left side

of the rear panel, please make sure to use the conductor to ground in case

of lightning!

Installation the Switch

Precautions: To avoid equipment damage and personal injury, observe the

following precautions:

The Switch room should be dry and ventilated, free from corrosive gases

and strong electromagnetic interference.

The humidity of the Switch equipment room should be lower than 90%

and around 25 degrees Celsius. If possible, install corresponding

facilities.

The grounding of the Switch shall comply with the grounding

requirements described in this manual, and shall be separately and well

grounded.

The Switch voltage should be stable to prevent abnormal operation of

the Switch caused by power supply voltage mutation, fluctuation and

other phenomena;

Keep a proper distance between the Switch and other devices. Do not

stack other devices with the Switch.

The connection cable between the Switch and the distribution frame

should be standardized and reasonable, and the distribution frame (box)

jumper wire should be concise and clear to prevent the phenomenon of

parallel lines and wires;

To avoid the danger of electric shock, do not open the chassis without

authorization; If any fault occurs, contact professional maintenance

personnel.

Safety Tips:

Use a three-hole socket with safe grounding, and ensure that the PGND

cable of the power socket is properly grounded.

Ensure sufficient space for heat dissipation and ventilation of the Switch.

Do not place heavy objects on the Switch.

6.Installation Environment

Before installation, make sure that the proper working environment is

available, including power requirements, adequate space, proximity to

other equipment to be connected, and other equipment in place. Please

confirm the following installation requirements:

Ensure the stability of the workbench and good grounding;

Check whether cables and connectors required for installation are in

place (less than 100m).

Environment requirements: The operating temperature ranges

from 0°C to 40°C and the relative humidity ranges from 5% to 90%.

Desktop Installation

Install the Switch on a desktop, please attach these cushioning rubber feet

provided on the bottom at each corner of the Switch in case of the external

vibration. Allow adequate space for ventilation between the device and the

objects around it.

Wall-mounted installation

In the first two fixed screw on the wall as shown in the figure below

Aim at the two fixed hole switches, and the machine smoothly

on the screw

Provide two screws with a diameter of about m3 and

a nut diameter of 5mm

Turn on the switch

The PoE switch can be used with AC power supply. Powering on the

switch, it will automatically initialize and its LED indicators will respond

as follows:

Firstly, the Power LED indicator will light up.

Then, the data LED indicators will flash momentarily for one second,

which represents a resetting of the system.

CE Mark Warning: This is a Class A product. In home environment, this

product may cause radio interference. In this case, the user may be

required to take appropriate measures.

Hereby Assmann Electronic GmbH, declares that the Declaration of

Conformity is part of the shipping content. If the Declaration of Conformity

is missing, you can request it by post under the below mentioned

manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid, Germany

Tabla de contenidos

Otros manuales de Cambiar de Digitus

Digitus

Digitus DN-95354 Manual de usuario

Digitus

Digitus DN-50011 Manual de usuario

Digitus

Digitus DA-70247 Manual de usuario

Digitus

Digitus DN-80071 BLACK RAPID 1000 Manual de usuario

Digitus

Digitus DS-12851 Manual de usuario

Digitus

Digitus DN-651154 Hoja de instrucciones

Digitus

Digitus DA-70245 Manual de usuario

Digitus

Digitus DS-44300 Manual de usuario

Digitus

Digitus DN-80111 Manual de usuario

Digitus

Digitus DS-43110 Manual de usuario

Digitus

Digitus DN-80068 Manual de usuario

Digitus

Digitus Pocket USB KVM switch Manual de usuario

Digitus

Digitus DA-73300-2 Manual de usuario

Digitus

Digitus DN-80066 Manual de usuario

Digitus

Digitus DA-70223 Manual de usuario

Digitus

Digitus DS-15202 Manual de usuario

Digitus

Digitus DS-12404 Manual de usuario

Digitus

Digitus DS-11900 Manual de usuario

Digitus

Digitus 5-Port HDMI Switch Manual de usuario

Digitus

Digitus DS-16202-1 Manual de usuario

Digitus

Digitus DN-651113 Manual de usuario

Digitus

Digitus DS-12423 Manual de usuario

Digitus

Digitus DA-70886 Manual de usuario

Digitus

Digitus DN-95347 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario