Digi-tech RP6 Manual de usuario

A Harman International Company

S-DISC™

PROCESSING

RP-6

Guitar Signal

Processor/Foot

Controller and Preamp

Owner's Manual

DECLARATION OF CONFORMITY

Manufacturer’s Name:Harman Music Group Incorporated

Manufacturer’s Address: 8760 S. Sandy Parkway

Sandy, Utah 84070, USA

declares that the product:

Product Name: RP-6

Product Options: All (requies a Class II power adapter that conforms to the requirements of

EN60065, EN60747, or equivalent).

conform to the following Product Specifications:

Safety: EN 60065 (1993)

IEC 65 (1987) with Amendments 1, 2 & 3

EMC: EN 55013 (1990)

EN 55020 (1991)

Supplementary Information:

The product herewith complies with the requirements of the Low Voltage Directive

73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.

Harman Music Group Incorporated

Vice President of Engineering

8760 S. Sandy Parkway

Sandy, Utah 84070, USA

Effective October 1, 1996

European Contact: Your Local DigiTech Sales and Service Office or

International Sales Office

3 Overlook Drive #4

Amherst, New Hampshire 03031, USA

Tel (603) 672-4244

Fax (603) 672-4246

Section 7 - Appendix

RP-6 Owner’s Manual

Table Of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Lithium Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . 4

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SECTION 1 - STARTUP Supplying power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Line Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pedalboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Parameter Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Display Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Value, Store, and Edit Keys. . . . . . . . . . . . . . . . . . . 8

Parameter Selection Keys . . . . . . . . . . . . . . . . . . . . 8

Main Output Level. . . . . . . . . . . . . . . . . . . . . . . . . . 8

Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CC Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . 8

Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Right Main Output. . . . . . . . . . . . . . . . . . . . . . . . . . 8

Left Main Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Headphone Output . . . . . . . . . . . . . . . . . . . . . . . . . 8

AC Line Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SECTION 2 - BASIC OPERATIONS About RP-6’s Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Bank Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Edit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Store Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Tuner Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table of Contents

RP-6 Owner’s Manual

SECTION 3- EFFECTS AND PARAMETERS About the Parameter Matrix. . . . . . . . . . . . . . . . . . . . . . 13

Compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CC Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Silencer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Master Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Speaker Cab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Wahs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Mod/Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Choruses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Flangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Phasers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Tremolos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Auto Panners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Pitch Shifters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Whammy™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Dual Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

SECTION 4- APPENDIX Reinitializing the RP-6 . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Program List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table of Contents

RP-6 Owner’s Manual

INTRODUCTION Congratulations, and thank you for your purchase of the DigiTech RP-

6 Guitar Signal Processor / Preamp. The RP-6 offers you the same

fresh approach to guitar sound creation as the now famous RP-10.

DigiTech’s revolutionary S-DISC™ processor makes it all happen. Its

compact size occupies less floor space, while maintaining the power

of analog distortion, with the precision and clarity of the S-DISC™ digi-

tal multi-effects. Special features of the RP-6 include:

• Full bandwidth effects (20-20kHz)

• Stereo signal processing

• Quick Module and Parameter access

• CC pedal which allows for real time control of certain Parameters

• Programmable cabinet emulation for running direct to a mixing

console (great for both studio and live applications)

• Front panel Presence control and headphone output

All of your effects needs can be filled by a single unit. This owner’s

manual is your key to understanding the powerful world of the RP-6.

Read it carefully. After you’ve had time to familiarize yourself with the

unit, try experimenting with unusual effects settings. You may achieve

some interesting results.

SAFETY PRECAUTIONS Do not open the unit. Do not attempt to service the unit yourself.

Refer all servicing to qualified personnel. Opening the chassis for any

reason will void the manufacturer’s warranty. Do not get the unit wet.

If liquid is spilled on the unit, shut it off immediately and take it to a

dealer for service. Disconnect the equipment during storms to prevent

damage.

U.K. ONLY - A moulded mains plug that has been cut off from the

cord is unsafe. Discard the mains plug at a suitable disposal facility.

NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A

DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET.

Do not use the mains plug without the fuse cover in place.

Replacement fuse covers can be obtained from your local retailer.

Replacement fuses are 13 amps and MUST be ASTA approved to

BS1362.

LITHIUM BATTERY WARNING CAUTION! This product contains a lithium battery. There is danger of

explosion if battery is incorrectly replaced. Replace only with an

Eveready CR 2032 or equivalent. Make sure the battery is installed

with the correct polarity. Discard used batteries according to manu-

facturer’s instructions.

ADVARSEL! Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes

kun batteri som anbefalt av apparatfabrikanten. Brukt batteri

returneres apparatleverandøren.

ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri av samme fabrikat og type. Levér

det brugte batteri tilbage til leverandøren.

Introduction and Safety

RP-6 Owner’s Manual

4VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma

batterityp eller en ekvivalent typ som rekommenderas av apparattil-

lverkaren. Kassera använt batteri enligt fabrikantens instruktion.

WARRANTY 1. The warranty registration card must be mailed within ten days after

purchase date to validate this warranty.

2. DigiTech warrants this product, when used solely within the U.S., to

be free from defects in materials and workmanship under normal

use and service.

3. DigiTech liability under this warranty is limited to repairing or

replacing defective materials that show evidence of defect, provid-

ed the product is returned to DigiTech WITH RETURN AUTHO-

RIZATION, where all parts and labor will be covered up to a period

of one year. A Return Authorization number may be obtained from

DigiTech by telephone. The company shall not be liable for any

consequential damage as a result of the product’s use in any cir-

cuit or assembly.

4. Proof-of-purchase is considered to be the burden of the consumer.

5. DigiTech reserves the right to make changes in design or make

additions to or improvements upon this product without incurring

any obligation to install the same on products previously manufac-

tured.

6. The foregoing is in lieu of all other warranties, expressed or implied,

and DigiTech neither assumes nor authorizes any person to

assume any obligation or liability in connection with the sale of this

product. In no event shall DigiTech or its dealers be liable for spe-

cial or consequential damages or from any delay in the perfor-

mance of this warranty due to causes beyond their control.

DigiTech™, S-DISC™, Whammy™ and Silencer™ are registered

trademarks of DOD Electronics Corporation.

The information contained in this manual is subject to change at any

time without notification. Some information contained in this manual

may also be inaccurate due to undocumented changes in the product

or operating system since this version of the manual was completed.

The information contained in this version of the owner’s manual super-

sedes all previous versions.

Warranty

RP-6 Owner’s Manual

SECTION 1 - STARTUP

SUPPLYING POWER Line Conditioning - The RP-6, like any piece of computer hardware,

is sensitive to voltage drops, spikes, and surges. Interference such as

lightning or power “brownouts” can seriously, and in extreme cases,

permanently damage the circuitry inside the unit. Here are some ways

to avoid this type of damage:

• Spike/Surge Suppressors - This is an inexpensive solution to all

but the most severe of AC line conditions. Surge protected

power strips usually cost only slightly more than unprotected

strips, making them a worthy investment for protection of all your

valuable gear.

• AC Line Conditioners - This is the best way to go for total pro-

tection from improper line voltages, albeit the more expensive

way. Line conditioners constantly monitor for excessively high or

low voltages and adjust accordingly, thus delivering consistent

power levels.

FRONT PANEL CONTROLS The front panel controls and functions of the RP-6 are as follows (refer

to diagram):

Section 1 - Startup

RP-6 Owner’s Manual

61) Pedalboard - The RP-6’s pedalboard consists of six footswitches.

The two Mode footswitches to the right of the Parameter Matrix

allow you to change from Program mode to Bank mode by press-

ing the UP & DOWN footswitches simultaneously. When changing

modes, the appropriate LED will light to indicate whether you are in

Program mode or Bank Mode. In Program Mode, the <UP> and

<DOWN> footswitches allow you to move through Programs, while

the four main switches, labeled 1 - 4, act as toggle On/Off switch-

es for Distortion, Modulation, Delay, and Reverb. In Bank mode,

the <UP> and <DOWN> footswitches allow you to move through

Banks, while the 1-4 footswitches are used to select Programs. If

footswitches 1 and 2 are pressed simultaneously, Tuner Mode will

be activated. If footswitches 3 and 4 are pressed simultaneously,

Bypass Mode will be activated.

2) Parameter Matrix - The Parameter Matrix consists of a group of

horizontal Effect LEDs and a second group of vertical Parameter

LEDs. The Effect LEDs are: Compressor, Distortion, Silencer,

Equalization, Speaker Cab, Wah Wah, Mod/Pitch, Dual Delay, and

Reverb. This matrix shows you exactly what Effects and Parameters

are in use.

3) Display Window - The display window shows all current operating

and programming information and is comprised of two parts: the

seven segment LED displays and the Signal, Clip, and Store indica-

tor LEDs. The first numeric LED in the display window indicates

whether you are in a User (U) or Factory Bank (F). The second

indicates the Bank number currently in use, and the third indicates

which Program number is currently in use. These numbers change

as you scroll through the available Programs. The functions of the

Signal, Clip, and Store indicator LEDs are as follows:

• Signal - Indicates whether a signal is entering the RP-6.

• Clip - Indicates analog clipping in the RP-6. Digital clipping can

be detected when the third vertical LED from the top of the

Parameter Matrix flashes. Distortion may be heard in the output

signal if either analog or digital clipping occurs. If analog clip-

ping occurs, check the Distortion On/Off levels. The levels may

need to be lowered to eliminate the problem. To reduce digital

clipping, the Master Volume and/or Effects levels should be

checked and adjusted accordingly. As always, let your ears be

the judge.

• Store - Lights when a Parameter has been changed in a

Program. When <STORE> is pressed once, the first seven seg-

ment LED in the Display window will flash. Once you have

selected the Bank and Program location where you want to store

your effects, press the <STORE> key again (see page 11, under

Edit Mode for further information on storing a Program).

Section 1 - Startup

RP-6 Owner’s Manual

4) Value, Store and Edit Keys - The Value <UP> and <DOWN> keys

allow you to scroll through the RP-6’s Programs, or change

Parameter values in Edit mode. The <STORE> key allows you to

store an edited Program in memory for later use. The <EDIT> key

allows you to edit the User and Factory Programs.

5) Parameter Select Keys -The <LEFT> and <RIGHT> Parameter

keys allow you to navigate the horizontal Effect LEDs of the

Parameter matrix. The <UP> and <DOWN> Parameter keys allow

you to navigate the vertical Parameter LEDs of the Parameter

matrix. These keys are only active in Edit mode.

6) Output Level - Controls the overall output level of the RP-6. Also

controls the overall level of the headphones.

7) Presence - Enhances the high frequency content of the overall

sound. This will affect all presets.

8) Continuous Control Pedal - This volume-type pedal allows real-

time control over Parameters in the RP-6.

REAR PANEL CONNECTIONS The RP-6 rear panel connectors and functions are as follows:

1) Input - This is the RP-6’s audio input. Plug your guitar in here.

2) Headphone Output - 1/4” stereo plug for headphones. The head-

phone level is controlled by the main output level knob.

3) Left/Mono Main Output - This is the RP-6’s left main audio output.

This output must be used if a mono effect is desired.

4) Right Main Output - This is the RP-6’s right main audio output.

Use both left and right main outputs to take advantage of stereo

effects.

5) AC Line Input - This is the AC adapter receptacle.

INPUT RIGHT

OUTPUT

LEFT/MONO

OUTPUT

HEADPHONES POWER

9VAC 1.33A

12345

Section 1 - Startup

RP-6 Owner’s Manual

Basic Guitar Setup

Section 1 - Startup

RP-6 Owner’s Manual

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pedal de música de digi-tech

digi-tech

digi-tech RP500 Manual de usuario

digi-tech

digi-tech Bass Squeeze Manual del propietario

digi-tech

digi-tech MAIN SQUEEZE Manual de usuario

digi-tech

digi-tech DIGIDELAY Manual de usuario

digi-tech

digi-tech GSP7 Manual de usuario

digi-tech

digi-tech HOTHEAD Manual de usuario

digi-tech

digi-tech HOTROD Manual de usuario

digi-tech

digi-tech PDS3500 Manual de usuario

digi-tech

digi-tech GNX4 Manual de usuario

digi-tech

digi-tech TRIO+ Band Creator+ Looper Manual de usuario

digi-tech

digi-tech Le Lyra Manual de usuario

digi-tech

digi-tech Drop Manual de usuario

digi-tech

digi-tech Bass Whammy Manual de usuario

digi-tech

digi-tech CROSSROADS Manual de usuario

digi-tech

digi-tech HARMONYMAN - Manual de usuario

digi-tech

digi-tech SDRUM Manual de usuario

digi-tech

digi-tech RP-1 Manual de usuario

digi-tech

digi-tech TRIO Manual de usuario

digi-tech

digi-tech DEATHMETAL Manual de usuario

digi-tech

digi-tech Bass Whammy Manual de usuario

digi-tech

digi-tech RP80 Manual de usuario

digi-tech

digi-tech BASS MULTI CHORUS Manual de usuario

digi-tech

digi-tech iPB-10 Manual de usuario

digi-tech

digi-tech GNX3000 Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario

digi-tech RP6 Manual de usuario

Manuales populares de Pedal de música de otras marcas